Contact Us

TPS3306-18DGKR

Brand: Texas Instruments
Texas Instruments TPS3306-18DGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3306-18DGKR — Power Management & Signal Chain | Superb Automation

TPS3306-18DGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3306-18DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3306-18DGKR dual supervisor with a power fail comparator and a 0.8 s watchdog

The TPS3306-18DGKR is the member of its family that adds a power fail input to the two rail monitors. SENSE1 watches 3.3 V against a 2.93 V threshold, SENSE2 watches 1.8 V against 1.68 V, and a third comparator with its own input and its own open drain output warns the processor that the input supply is falling before the rails themselves drop. The reset output and the power fail output are both open drain, so they can be wire-ORed with other sources.

The family number decides the rail pair and the delay. The -18 pair is 3.3 V and 1.8 V, and the reset stays asserted for 100 ms after both rails are good. The watchdog times out at 0.8 s, which is the tightest in this family and comes from the same document revision that added the power fail block. The part runs from 2.7 V to 6 V and draws 15 microamp typical, so it can sit on a rail that is always alive.

Key parameters taken from the TPS3306 document

Monitored rails3.3 V on SENSE1 against 2.93 V typical, 1.8 V on SENSE2 against 1.68 V typical
Threshold windowThe 1.68 V row is specified from 1.64 V to 1.72 V, and the 2.93 V row from 2.86 V to 3.00 V
Power fail inputPFI compared against an internal 1.25 V reference, with an open drain PFO output
Power fail dividerExternal, and the vendor suggests about 1 megohm total to keep the divider current small
Reset delay100 ms typical after both sense inputs rise above their thresholds
Watchdog0.8 s time-out, retriggered by a positive or a negative transition at WDI
Supply range2.7 V to 6 V
Supply current15 microamp typical
OutputsOpen drain RESET and open drain PFO, both active low
Reset validityDefined from VDD 1.1 V
TemperatureMinus 40 C to 85 C
PackageVSSOP-8, 2500 pieces on a large reel, moisture level 1, marking AID

The power fail threshold is 1.25 V at the PFI pin, and the trip point is set by a divider the board supplies. That divider is the only external component in the whole arrangement, and it is also the only place where the warning point can be set wrong.

Where the numbers matter in a real build

The power fail comparator is the reason to choose this part over the TPS3305. On a board with a 24 V input and a local 3.3 V regulator, the input falls slowly as the bulk capacitor discharges, and the processor needs a few milliseconds of warning to store its parameters. PFI sees that fall through the divider long before the 3.3 V rail crosses 2.93 V, which is exactly the time the software needs.

The second point is the open drain output. Both RESET and PFO need a pull up, and the pull up decides the rise time and the current the part has to sink. A 100 kiloohm pull up on a board with 20 pF of track capacitance gives a rise time that is fine for a processor reset pin but slow for anything that samples the line at speed.

The third is the watchdog at 0.8 s. That is shorter than the 1.6 s of the TPS3305, so a service task written for the other part will reset this one. The window is not trimmed, and a service timer that runs from the same oscillator as the processor has to be checked against the fast end of the range.

What to check before a purchase order is released

  • The rail pair in the dash number, since the -20 and -25 members look identical on a drawing but watch different rails.
  • The PFI divider, calculated against 1.25 V and checked with the divider's own tolerance.
  • The pull ups on RESET and PFO, because an open drain output with no pull up never goes high.
  • The watchdog period in the service routine, measured against 0.8 s and not against a rounded one second.
  • The 100 ms reset delay against the processor start-up, which is shorter than the 200 ms of the sibling family.
  • Whether the board needs a manual reset button, since this family has no MR pin.

Which projects this part fits

The vendor lists multivoltage DSPs and processors, portable battery powered equipment, embedded control systems, intelligent instruments and automotive systems. The power fail input points at equipment that has to save state when the mains or the vehicle supply is cut, which covers most instruments with a display and most embedded controllers with a non volatile store.

Questions that come up before a purchase order is released

What is the difference from the TPS3305?

The 3305 has a manual reset input and a watchdog output but no power fail comparator. The 3306 has the power fail comparator and open drain outputs but no manual reset. The rail pairs and the pin count are the same.

Can PFI monitor a negative supply?

No. PFI compares a positive voltage against 1.25 V, so a negative rail needs an inverting arrangement in front of it.

Does PFO assert before RESET?

That depends on the divider. The power fail input is intended to trip earlier than the rail monitor, but the actual order is set by the divider values on the board, not by the part.

Is the watchdog output separate?

There is no watchdog output on this member. A watchdog time-out asserts RESET, and the only separate flag is PFO.

How SUPERB handles this line

Supervisors with a power fail input are usually bought with the memory and the connector they protect, because the whole group is on the same board and the same schedule. Our power management cross reference puts this family beside the parts it replaces, rail pair and delay included. Our kitting service covers a build where the supervisor, the store and the passives ship together, and the lead time solutions page explains what we do when one line of that kit is short.