Contact Us

TPS3305-18DR

Brand: Texas Instruments
Texas Instruments TPS3305-18DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3305-18DR — Power Management & Signal Chain | Superb Automation

TPS3305-18DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3305-18DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3305-18DR dual supervisor for a 3.3 V rail and a 1.8 V rail with a watchdog output

The TPS3305-18DR watches two rails at once, 3.3 V and 1.8 V, and holds a single reset line until both are good, then waits 200 ms before releasing it. A watchdog input and a separate watchdog output sit beside the reset, so a processor that stops toggling its service pin is reset without any external logic. The whole arrangement runs from 2.7 V to 6 V and draws at most 40 microamp, which is why it still appears on industrial boards that were specified long before integrated sequencers became common.

The dash number is the rail pair, not a revision. TPS3305-18 watches 3.3 V and 1.8 V, the -25 watches 3.3 V and 2.5 V, and the -33 watches 5 V and 3.3 V. The two thresholds are trimmed inside the part, at 2.93 V and 1.68 V for the -18, so no divider is needed and the accuracy does not depend on resistor tolerance. A board that was set up for a -25 part will not reset correctly on a -18 part even though the pinout is identical.

Key parameters taken from the TPS3305 document

Monitored rails3.3 V on SENSE1 with a 2.93 V typical threshold, 1.8 V on SENSE2 with a 1.68 V typical threshold
Supply range2.7 V to 6 V on the VDD pin
Reset delay200 ms typical, fixed, no external capacitor
WatchdogTime-out 1.6 s typical, retriggered when either sense pin rises above its threshold and by a toggle at WDI
Supply current40 microamp maximum, which is the figure to use for a standby budget
Reset validityOutput defined from VDD 1.1 V, so the reset is real before the rails come up
OutputsRESET for the processor and WDO for the watchdog, which allows the watchdog to be reported without a full reset
Manual resetMR pin, active low, with an internal pull up
ReferenceTemperature compensated, which is what keeps the 2.93 V threshold stable over the full range
TemperatureMinus 40 C to 85 C
PackageSOIC-8, 2500 pieces on a large reel, moisture level 1, marking 30518
Alternate bodyThe DGN body is the same silicon in HVSSOP-8, at 80 pieces per tube or 2500 on a reel, marking AAM

The two rails are monitored independently, so the reset asserts when either one falls. That sounds obvious, but it changes the release condition: both have to be good, and then the 200 ms delay starts. A 1.8 V rail that comes up after the 3.3 V rail by more than 200 ms still gets a clean reset, because the timer only starts when the second rail crosses its threshold.

Where the numbers matter in a real build

The 1.6 s watchdog period is the number that decides how the service routine is written. A service task that runs every second leaves half a second of margin against a typical part, and the same task leaves 800 ms against the fast end of the window. The document does not trim the watchdog oscillator, so the spread has to be taken seriously on a product that ships for ten years.

The second figure is the 40 microamp maximum. For a board that runs from a battery or a 24 V loop, that current is the price of keeping a supervisor alive, and it is measured with the part doing nothing but watching. Any external divider that replaces the internal one would add more than the part itself draws.

The third is the pair of thresholds. A 3.3 V rail with a 5 per cent tolerance sits at 3.135 V at the low end, which is 300 mV above the 2.93 V typical threshold. That margin is generous on purpose, because the part was made for rails with wide tolerance, not for a core rail that must be reset inside 1 per cent.

What to check before a purchase order is released

  • The dash number against the rail pair on the drawing, because the pinout is the same across the family and the thresholds are not.
  • The watchdog period in the service routine against the 1.6 s typical, with margin at the fast end.
  • Whether the board needs the WDO output wired, since a watchdog warning without a reset is often more useful for diagnostics than a reset alone.
  • The 200 ms delay against the processor start-up time, especially where a large bulk capacitor holds the 3.3 V rail up for longer.
  • The MR pin pull up, because an external pull down stops the board from starting.
  • The body, D or DGN, since the two are the same silicon on different leadframes with different reel sizes.

Which projects this part fits

The vendor lists processor supply monitoring, industrial equipment, automotive systems, portable and battery powered equipment, wireless communication systems, and notebook and desktop computers. The pattern is a processor with a core rail and an input and output rail, where the two have to come up in a defined order and the software already has a service task that can double as a watchdog pulse.

Questions that come up before a purchase order is released

Does the part sequence the two rails?

No. It monitors them and holds the reset until both are good. Sequencing, where one rail is enabled after the other, needs a separate device or a discrete arrangement.

Can the watchdog be disabled?

It can be kept quiet by toggling WDI, but it cannot be switched off. A board that has no service task has to keep the pin moving or accept a reset.

Why two outputs instead of one?

WDO reports the watchdog condition, and RESET reports the rail condition. Wiring only RESET works, and the diagnostic value of WDO is then lost.

Is the threshold the same as the rail tolerance?

No. The 2.93 V threshold is roughly 11 per cent below a 3.3 V nominal, which is a brown-out detector, not a precision monitor. Boards that need a 1 per cent window need a different family.

How SUPERB handles this line

Old supervisor families are still bought in volume because they sit on boards that are in service for a decade, and the dash numbers are where most ordering mistakes happen. Our power management cross reference lists the members of this family beside the parts they replace, rail pair included. The drop in replacement check covers the questions to settle before a substitute is accepted, and our one stop BOM sourcing is the route we use when the supervisor, the memory and the connector all come from one build.