Contact Us

TPS3128E18DBVR

Brand: Texas Instruments
Texas Instruments TPS3128E18DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3128E18DBVR — Power Management & Signal Chain | Superb Automation

TPS3128E18DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3128E18DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3128E18DBVR: 1.8 V supply supervisor with watchdog and manual reset in SOT-23-5

TPS3128E18DBVR is a processor supervisory circuit that holds a reset output low until the 1.8 V rail is valid, then watches a software heartbeat and forces reset again if the pulses stop in a SOT-23 (DBV) body of 5 pins. The threshold is fixed at the factory for a 1.8 V rail, the reset delay is 180 ms typical, and the watchdog times out after 1.4 s typical if the monitored pin stops toggling. The reset output is open drain and active low, and the part works down to a 0.9 V supply, which is what allows it to supervise a rail that is still ramping.

Order code and package

Order code read outTPS3128 E18 DBV R: supervisor with watchdog and manual reset, 1.8 V threshold, SOT-23 five pin, large tape and reel
PackageSOT-23 (DBV), 5 pins, 2.90 mm by 1.60 mm
Carrier in the vendor addendumTPS3128E18DBVR at 3000 pieces on a large reel; the DBVT row is the same part on a small reel
StatusActive and in production on the vendor addendum dated 17 July 2026
Moisture levelLevel 1, 260 degrees unlimited floor life
Lead finishNickel palladium gold with tin, quoted as NIPDAU or SN
Part markingPFTI, with the temperature range minus 40 to plus 85 degrees

Electrical parameters that decide the application

Supply range0.9 V to 3.3 V on VDD, so the device is specified below the rail it supervises
ThresholdTPS3128E18 trips at 1.71 to 1.77 V on a falling rail, a window of about plus or minus 1.7 percent
Hysteresis20 mV typical for a threshold between 1.4 V and 2 V, which is the band this part sits in
Reset delay100 ms minimum, 180 ms typical and 260 ms maximum from the rail crossing the threshold
Watchdog timeout0.8 s minimum, 1.4 s typical and 2.1 s maximum, retriggered by an edge on the WDI pin
Watchdog inputPulse width from 100 ns, with a 1 microsecond minimum on the manual reset pin
Manual resetA low on MR forces reset, with an internal pull up of 90 kohm typical and a 1 microamp maximum input current
Supply current14 microamp typical at 3.3 V, 30 microamp maximum over the temperature range, and about 5 microamp more while the reset delay is running
Reset outputOpen drain active low, able to sink 3 mA at 0.4 V, so an external pull up to the processor rail is required
Output validityReset is not valid below 0.9 V, which is stated explicitly and matters when a rail collapses
Propagation17 microsecond delay from supply to reset, and 0.1 microsecond from the manual reset pin
Absolute maximumMinus 0.3 V to 3.6 V on the supply, 5 mA into any pin, and a 260 degree soldering limit

Which member of the TPS312x family this is

TPS3128E18DBVRthe part on this page: watchdog, manual reset, open drain active low output, 1.8 V threshold
TPS3123push pull active low output with the same watchdog and manual reset, chosen when no pull up is wanted
TPS3124watchdog but no manual reset, and a push pull output
TPS3125 and TPS3126no watchdog; the 3125 has a push pull output and the 3126 an open drain one
Threshold codesE12 at 1.14 to 1.18 V, E15 at 1.43 to 1.48 V, E18 at 1.71 to 1.77 V and L30 at 2.64 to 2.71 V, each a separate order code

Points to check before this part goes on a BOM

The threshold window on this part is tight enough to be used directly on a 1.8 V rail with a five percent supply. A rail at minus five percent sits at 1.71 V, which is the bottom of the published window, so a board that runs at the edge of its tolerance can assert reset at the same moment the rail is still legal. That is the case to check on paper: if the regulator is specified at plus or minus three percent the margin is comfortable, and if it is a loose LDO at plus or minus five percent the board should move to a lower threshold code or accept a reset in the worst case.

The watchdog is retriggered by an edge rather than by a level, and the pulse only has to be 100 ns wide. That is a convenient interface for a firmware loop that toggles a port pin, because the timing accuracy of the pulse does not matter. What does matter is the 0.8 to 2.1 s window: a firmware loop that takes longer than 0.8 s between toggles will reset on some units and not others, and the failure looks like an intermittent brown out rather than a watchdog event.

The reset output is open drain, so the pull up resistor is part of the circuit rather than an afterthought. With a 3 mA sink capability and a 0.4 V low level, a 10 kohm pull up to 1.8 V draws 180 microamp and gives a rise time of a few microseconds into a few tens of picofarads. A much weaker pull up, chosen to save current, makes the edge slow enough that some processors see it as an analogue input rather than a reset.

Reset is only defined above 0.9 V, and the vendor says so explicitly. On a rail that collapses slowly, the output can go to any state below that level, so a processor that is still executing at 0.8 V may see a released reset. The usual answer is a resistor from reset to ground or a second supervisor on the higher rail, and it is worth checking because the symptom, a processor that starts executing garbage during power down, is hard to trace back to a supervisor.

The 180 ms delay is long enough to cover a regulator's own soft start and short enough not to delay a boot visibly. It is fixed at the factory and cannot be changed with a capacitor, which is a difference from older supervisor families. If a product needs a different delay the choice is a different part rather than a different component value, and that should be settled before the board is released.

The manual reset pin has an internal 90 kohm pull up, so it can be left open. When it is driven from a push button or from another logic device the driver has to overcome that pull up, and a 1 microamp maximum input current means the pin is easy to drive. The 1 microsecond minimum pulse is the specification to respect, because a very short glitch can be filtered and a longer one cannot.

Where this order code fits

Used on processor and DSP boards that need a defined reset at power up plus a heartbeat monitor: industrial controllers, building automation nodes, telecom line cards, portable instruments and any 1.8 V core rail that must be supervised down to 0.9 V. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does it need an external pull up on reset? Yes. The output is open drain and only sinks current, so a resistor to the processor's reset rail is required. A 10 kohm part gives a clean edge with a small load; larger values save current but slow the rise.

What if the watchdog is not used? The pin has to be driven, because a floating watchdog input is not a defined state. Toggling it from the firmware loop is the normal answer, and tying it to a clock output is the alternative. The part cannot have the watchdog disabled by a pin.

Is the threshold adjustable? No. It is set at the factory and encoded in the order code, E18 being 1.71 to 1.77 V. A different rail needs a different code from the same family rather than an external divider.

How does it behave during a slow power down? Reset is only guaranteed above 0.9 V. Below that the output state is undefined, so a board that needs a defined reset during a long decay should add a resistor to ground on the reset line or supervise the higher rail as well.

Is the part still in production? The vendor addendum dated 17 July 2026 lists TPS3128E18DBVR as active and in production, 3000 pieces on a large reel, so there is no last time buy condition to plan around at the moment.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.