TPS3106K33DBVR
Product Specifications
TPS3106K33DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3106K33DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3106K33DBVR: Voltage supervisor that draws 1.2 uA and holds reset valid down to 0.4 V
TPS3106K33DBVR is a supply voltage monitor in the six pin DBV body that supervises a 3.3 V rail with 0.75 percent trip accuracy, draws 1.2 uA, and keeps the reset output defined while the supply is as low as 0.4 V in a SOT-23-6 body of 6 pins. The TPS3106 is the watchdog member of the TPS31xx family of ultralow current supervisors, with a fixed 3.3 V threshold in this order code and a 130 ms power on reset delay. The trip point is accurate to 0.75 percent, the supply current is 1.2 uA typical, and the reset output stays valid with the supply as low as 0.4 V, which is the property that keeps a processor in reset during a slow brownout instead of letting it run at an undefined voltage. A separate power fail input compares against 0.551 V and drives its own output, and the sense and watchdog inputs are independent of the supply pin.
Order code and package
| Order code | TPS3106K33DBVR |
| Supervised voltage | 3.3 V, fixed threshold |
| Trip point accuracy | 0.75 percent |
| Supply current | 1.2 uA typical |
| Reset delay | 130 ms power on reset |
| Reset output | push pull or open drain depending on the variant |
| Package | six pin SOT-23, DBV body |
| Temperature range | minus 40 C to 125 C |
Electrical parameters that decide the application
| Threshold family | 0.9 V, 1.2 V, 1.5 V, 1.6 V, 2 V and 3.3 V |
| Reset valid down to | 0.4 V supply |
| Power fail input threshold | 0.551 V |
| Power fail output | goes high when the input rises above 0.551 V |
| Hysteresis, 0.8 V to 1.5 V thresholds | 20 mV |
| Hysteresis, 1.6 V to 2.4 V thresholds | 30 mV |
| Watchdog | input provided on this family member |
| Output drive at 3.3 V | 3 mA sink, 3 mA source |
| Maximum continuous supply | 3.6 V, and not more than 1000 hours at that level |
Points to check before this part goes on a BOM
One point two microamps is 10.5 mAh over a year, which against a 220 mAh coin cell is about five percent of the cell per year, and against a 2000 mAh lithium cell it is half a percent. The number matters because a supervisor is on whenever the product is off, so its current is the floor of the standby budget. The comparison that decides whether it is acceptable is with the self discharge of the cell, which for a lithium primary is about one percent per year, so the supervisor is roughly the same size as the cell's own loss and worth choosing carefully rather than adding as an afterthought.
Keeping the reset output valid down to 0.4 V is the specification that separates a supervisor from a comparator. A processor that is held in reset by an output that itself becomes undefined at 1 V is not held in reset at all: the output floats, the processor's reset pin drifts, and the device executes random instructions from a supply that cannot support them. The 0.4 V figure covers the whole brownout, including the slow decay of a supply after the power is removed, which is the interval where a processor with a low threshold can start executing out of a partially charged rail.
The 0.75 percent trip accuracy on a 3.3 V rail is 25 mV, which is the margin available between the trip point and the minimum operating voltage of the load. A processor specified to 3.0 V needs the supervisor to trip above that, and a 3.3 V rail with a 5 percent tolerance is 3.135 V at its low limit. The trip point has to sit between the load minimum and the rail minimum, and 25 mV of accuracy is what makes that window usable. A supervisor with 3 percent accuracy would consume most of the window on one side.
The hysteresis of 20 to 30 mV is small and it is deliberate. A supervisor with a large hysteresis lets the rail sit below its trip point for a long time before the reset releases, and a supervisor with none chatters on a slow supply. On a battery product the supply falls slowly at end of life, and 30 mV of hysteresis at a 3.3 V threshold means the reset asserts at 3.07 V and re leases at about 3.10 V, so a supply wandering in that band produces a clean single reset rather than a burst of them.
The independent sense input is what makes a fixed threshold part usable on an arbitrary rail. The pin compares against 0.551 V, so a divider from a 5 V rail with equal resistors puts the threshold at 1.1 V, and a divider from a 1.2 V rail puts it wherever the ratio decides. The divider current is the board decision: a 1 Mohm pair draws 1.65 uA at 3.3 V, more than the supervisor itself, so a battery product uses 10 Mohm and accepts the slower response that comes with the higher impedance and the leakage that comes with it.
The watchdog input on this family member is the reason to choose it over the plain supervisor. A processor that stops toggling the input within the timeout gets a reset, which recovers a firmware hang without a human. The timeout is set by the part number and is not adjustable, so the firmware has to toggle faster than the specified window, and a firmware that does a long blocking operation has to either service the watchdog from an interrupt or disable it during that operation, which is a decision that should be visible in the code review.
A six pin SOT-23 package with a 3.6 V maximum continuous supply and a 1000 hour restriction at that value is a reminder that a supervisor sees the worst of the supply. On a 3.3 V rail with a 10 percent tolerance the supply reaches 3.63 V, which is above the recommended maximum and inside the absolute maximum. The part survives it and its life is shortened, so a rail that sits at 3.6 V continuously is outside the intended application even though the board works on the bench.
Where this order code fits
This order code belongs on battery powered instruments, wireless sensor nodes, portable medical devices and any product that spends most of its life asleep and has to wake into a defined state. It is also the part chosen where the processor core runs from a rail that is different from the one being supervised, because the sense input is separate from the supply pin and a divider on the sense pin sets the threshold for any rail above 0.9 V. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Can the threshold be changed without changing the part? Yes, with a divider on the sense input, which compares against 0.551 V. The divider current becomes part of the standby budget, and a high impedance divider has to be checked against the leakage of the board. The fixed threshold variants exist for the case where the divider current is not acceptable.
What does reset valid down to 0.4 V mean in practice? It means the reset output is defined throughout a brownout rather than only while the supply is in regulation. A processor is therefore held in reset until the rail is high enough to run, which prevents the random execution that a floating reset pin allows at partial supply.
How does the watchdog help? It resets a processor that stops toggling its input within the timeout, which recovers a firmware hang. The timeout is fixed by the part number, so the firmware has to service it on a schedule, and a blocking operation has to be planned around it rather than discovered when the product resets in the field.
Is 1.2 uA low enough for a coin cell product? It is 10.5 mAh a year, about five percent of a 220 mAh coin cell and comparable with the cell's own self discharge. It is low enough that the supervisor is not the dominant term, provided the divider on the sense pin, if there is one, is in the megaohm range.
SUPERB holds and sources this supervisor line against the exact order code, with the reel, date code and country of origin stated on the offer. When a reset circuit has to move to a second part, the BOM Shortage Recovery page sets out the checks that separate a working substitute from one that fails on the bench.