Contact Us

TPS2H160AQPWPRQ1

Brand: Texas Instruments
Texas Instruments TPS2H160AQPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2H160AQPWPRQ1 — Power Management & Signal Chain | Superb Automation

TPS2H160AQPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2H160AQPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2H160AQPWPRQ1 40 V dual high-side switch with an adjustable current limit

The TPS2H160AQPWPRQ1 is the version A member of a two channel smart high side switch family from Texas Instruments, built for 12 V and 24 V vehicle rails. Each channel carries a 160 milliohm NMOS switch, a gate drive charge pump and a diagnostic block in one 16 pin HTSSOP body, so a module that used to need two discrete FETs, two drivers and a handful of sense resistors now needs one part and two setting resistors. The working range is 3.4 V to 40 V, which covers a nominal 12 V rail, a 24 V rail and the load dump clamp that follows.

The letter at the end of the family name decides what the fault pin does. Version A brings the status out as open drain outputs, one per channel plus a global fault, so a microcontroller reads a logic level. Version B replaces that with an analog current sense pin. The two versions share the same silicon, the same pin count and the same protection, and they are not interchangeable on a board because the diagnostic pin means something different on each. Every order code on this page is version A.

Key parameters taken from the TPS2H160-Q1 document

Supply range3.4 V to 40 V working, with loss of ground and loss of battery protection
ChannelsTwo independent high side switches, 160 milliohm nominal each
On resistance155 milliohm typical at 25 C, rising to 280 milliohm at 150 C junction
Standby currentBelow 0.5 microamp with the channels off, which is the number that decides whether a parked vehicle drains its battery
Operating current7 mA with both channels at 0.5 A and a 2 A limit, including the charge pump
Internal current limit6.8 A minimum, 9 A typical, 15 A maximum when the CL pin is tied to ground
External current limitSet by one resistor from CL to ground, with the ratio K(CL) of 2500 and the internal reference VCL(th) of 0.8 V, so 800 ohm gives 2.5 A
Limit accuracy8 per cent at 50 mA and 100 mA of load, and the external limit is specified only above 1.5 times the set point
DiagnosticsOvercurrent, short to ground, open load, short to battery, thermal shutdown flag, and a global fault for a fast interrupt
Clamp65 V drain to source clamp with an optimised slew rate for inductive loads
Turn-on delay20 microseconds minimum, 50 typical, 90 maximum from the input pin to 10 per cent of the output
QualificationAEC-Q100 grade 1, minus 40 C to 125 C ambient, HBM class H2 and CDM class C4B
PackageHTSSOP-16, 2000 pieces on a large reel, moisture level 3 with a 168 hour floor life, marking 2H160AQ

One row deserves attention before anything else. The part in the table above is version A, so it has no analog current sense pin. If a drawing asks for a proportional current output, the part number has to end in the version B string, and the board around it changes.

Where the numbers matter in a real build

The external limit is the feature that most often gets copied wrong. The resistor is not a shunt. It sets a threshold through a 2500 to one ratio, so 800 ohm gives 2.5 A while 400 ohm gives 5 A, and the tolerance of that resistor translates one for one into the tolerance of the limit. A 1 per cent resistor is worth the extra cent here, because a 5 per cent part moves a 2.5 A limit by 125 mA before the silicon tolerance is counted at all.

The second number is the limit window itself. The document specifies the external limit only for overload conditions above 1.5 times the set value, which means a load drawing 1.2 times the limit is inside the region where the part is not guaranteed to hold. Boards that rely on the switch as a precision current source need a different arrangement. Boards that use it to survive an inrush into a capacitive load are exactly what it was made for.

The third is thermal. At 155 milliohm and 1 A per channel the part dissipates 0.31 W before the charge pump is counted, and the 16 pin PWP body with its exposed pad handles that easily. In a sealed box at 85 C ambient, four channels of a lighting module share the same air, and the 280 milliohm figure at 150 C junction is the one that shows how much margin disappears as the box heats up.

What to check before a purchase order is released

  • Whether the drawing needs open drain status or analog current, because the two are different order codes and different boards.
  • The resistor at the CL pin, calculated from 2000 divided by the wanted limit in amps, and its tolerance.
  • The 65 V clamp against the actual inductive load, since a relay or solenoid that is switched off stores energy the clamp has to absorb.
  • The thermal path under the exposed pad, because a 16 pin HTSSOP on a two layer board behaves very differently from the same part on four layers with a copper plane.
  • The moisture level, since level 3 with a 168 hour floor life sets a reflow window that a level 1 part does not have.
  • The standby current budget of the whole module, where 0.5 microamp per switch is usually small against the rest of the load but not always.

Which projects this part fits

The vendor lists dual channel LED drivers, bulb drivers, relays, solenoids, valves, and sub-modules such as cameras, sensors and displays. The common thread is a load that lives outside the controller board and can be shorted to ground or to the battery by a harness fault. A lighting module with two strings is the simplest case. A camera or sensor sub-module that has to be powered down while the main rail stays alive is the other.

Questions that come up before a purchase order is released

Does the family have a pin to pin replacement?

Version B replaces version A on the same footprint, but the diagnostic pin changes function. A board that reads a logic level from that pin has to be reworked before a version B part goes on it.

Can the limit be changed after the board is built?

Yes, because the limit is set by one external resistor. That is the reason the part is popular in modules that serve several load currents from one printed circuit.

What happens on a short to battery?

The channel reports the fault through the status output and the global fault pin. The switch itself is not damaged, because the drain to source clamp and the current limit both sit between the battery and the load.

Is the standby figure measured with the diagnostic block on?

The 0.5 microamp figure is quoted with the input pins, the diagnostic enable and the outputs all at 0 V, which is the state a parked module sits in. Leaving the diagnostic enable high adds to it.

How SUPERB handles this line

Protection parts on a vehicle board usually arrive together with the connector, the harness side fuse and the rest of the channel, so the purchasing job is a kit rather than a reel. Our power management cross reference lists the discrete arrangement this family replaces, and the incoming inspection plan covers what we check on a smart switch before it goes to the line. Where a running board needs the part after a vendor change, the obsolete part cross reference hub is the first stop.