Contact Us

TPS25940ARVCR

Brand: Texas Instruments
Texas Instruments TPS25940ARVCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS25940ARVCR — Power Management & Signal Chain | Superb Automation

TPS25940ARVCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS25940ARVCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS25940ARVCR 2.7 V to 18 V eFuse with true reverse blocking and a low power sleep mode for drives

The TPS25940A is an 18 V eFuse with two features that a plain hot swap controller does not have: back to back FETs that block current in both directions, and a low power mode that keeps the rail alive while drawing about 95 microamp so a drive can meet the device sleep requirement of the SATA specification.

The current path is a 42 milliohm pair of FETs, the limit is adjustable from 0.6 A to 5.3 A at 8 per cent accuracy, and a current monitor output carries the load current with the same 8 per cent accuracy so a system can measure what a drive is drawing without a sense resistor. Overvoltage and undervoltage thresholds are programmable to 2 per cent, and the part reports power good and fault states to the system.

Key parameters taken from the TPS25940ARVCR document

Operating range2.7 V to 18 V, with 20 V absolute maximum
Current pathBack to back FETs, 42 milliohm typical, which block current in both directions
Current limit0.6 A to 5.3 A adjustable at 8 per cent accuracy, with 4.81 A maximum at a 20 k resistor
Current monitorAnalogue output with 8 per cent accuracy, which removes the need for an external sense resistor
Sleep mode current95 microamp typical and 130 microamp maximum in the low power mode
Enabled currentAbout 199 to 270 microamp typical at 12 V and 18 V
Disabled current15 microamp typical and 25 microamp maximum at 12 V to 18 V
Overvoltage and undervoltageBoth programmable, with 2 per cent threshold accuracy
Reverse blockingTrue blocking from the first microsecond, with a reverse voltage shutoff that acts in about 1 microsecond
Ramp controlOne capacitor sets the output slew, which keeps the inrush into the load capacitance inside the limit
Fault reportingPower good and fault outputs for the system controller
Fail safeThe limit resistor is checked at start up, and an open or shorted resistor produces a defined current rather than an undefined one
ApprovalsUL 2367 recognized under file E169910 and safe during the UL 60950 single point failure test
PackageWQFN of 20 pins
Carrier3000 pieces on a large reel
MoistureLevel 1 at 260 degrees with an unlimited floor life, printed on the A row as level 2 with a one year life
Part marking25940A
TemperatureMinus 40 to plus 85 degrees on the A row of the addendum

Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.

Where the numbers matter in a real build

The sleep mode is the reason this part exists in a drive. A SATA drive has to enter a device sleep state where the host removes the main rail and the drive keeps a small circuit alive, and the current that circuit may draw is tightly limited. The 95 microamp figure is what makes the eFuse itself compatible with that state, since a controller that draws a milliamp would blow the budget on its own.

The back to back arrangement is what separates true reverse blocking from a body diode. A single FET blocks current in one direction and conducts through its body diode in the other, so a load with holdup capacitance discharges into a collapsed input. Two FETs in series, with their body diodes opposing, block both ways, and the part then re-enables once the input recovers.

The current monitor output is worth more than it looks on a drive. Measuring the load current without a sense resistor saves the drop and the part, and the 8 per cent accuracy is enough for a system to tell a spinning drive from an idle one and to log the difference. It is not a metering output, and a product that needs 1 per cent has to use a dedicated monitor.

The 42 milliohm path gives 0.18 W at 2 A and 1.2 W at 5.3 A, and the 20 pin body has a pad that has to be treated as a thermal terminal. The temperature range on the A row of the addendum stops at 85 degrees, which is lower than the junction range printed in the features, so a product that runs near the top of the load range has to use the addendum figure for its derating.

The fail safe behaviour of the limit resistor is printed because the part is used on safety rated rails. An open resistor sets a defined current instead of leaving the path unprotected, and the document prints what that current is. A safety file can therefore argue that a single component failure does not remove the protection.

The programmable overvoltage and undervoltage thresholds are the two pins that decide when the path opens, and 2 per cent accuracy is tighter than most dividers a board would use. A 12 V rail monitored at 13.2 V and 10.8 V therefore behaves as specified even with 1 per cent resistors, which is a rare case where the controller is more accurate than the network around it. The thresholds are set once, so a product that has to work from a 5 V and a 12 V source needs either two resistor networks or a threshold that suits both, and the second option is usually the reason a rail trips at the wrong point in the field.

The ramp capacitor is often left at the vendor value from an application note, and that is the second most common reason a drive rail fails a start up test. The capacitor has to hold the inrush into the load capacitance inside the current limit for the time the drive needs to come up, and a drive with a large input capacitance and a fast requirement is a case that has to be calculated from the limit, the capacitance and the allowed start time rather than copied.

  • The limit resistor value and its fail safe behaviour, since the part is often used where a single component failure has to be argued.
  • The device sleep current, because the 95 microamp figure is the budget the drive state depends on.
  • The reverse blocking, since a load with holdup capacitance will discharge through a single FET.
  • The current monitor output and its 8 per cent accuracy, which decides whether it can replace a sense resistor.
  • The thermal pad, because 5.3 A through 42 milliohm is over a watt.
  • The temperature range on the addendum row, which stops at 85 degrees and is lower than the junction figure in the features list.

Which projects this part fits

This part fits solid state drives, hard disk drives and the storage backplanes that feed them, plus PCIe, SATA and SAS carriers where the rail has to survive a device sleep state. It also fits any 12 V or 5 V branch with a load side capacitor that must not discharge back into a failed supply.

Questions that come up before a purchase order is released

What is the low power mode for?

It keeps the eFuse alive while the drive is in a device sleep state, drawing about 95 microamp. Without it the controller alone would exceed the current budget the state allows.

Why two FETs?

A single FET conducts through its body diode in reverse. Two FETs in series with opposing body diodes block current in both directions, which is what stops a load capacitor discharging into a collapsed input.

How accurate is the current monitor?

8 per cent, which is enough to distinguish load states and to log current, but not a metering grade output.

Can the current limit be set to 5 A?

The range goes to 5.3 A and a 20 k resistor gives 4.81 A maximum. The 8 per cent accuracy means the actual limit sits in a window around the set point.

What is the operating temperature range?

The features list a junction range, but the addendum row for this string reads minus 40 to plus 85 degrees, and that is the figure to use for derating a product that runs near the top of the load range.

Does it need an external sense resistor?

No. The limit is set by a resistor and the current is reported on an analogue output, so the sense element is inside the package.

How SUPERB handles this line

An 18 V eFuse on a storage rail is chosen for its reverse behaviour and its sleep current, and both are printed in the vendor document rather than in a summary. Our power management cross reference lists the devices this part is cross referenced against, our safety stock planning covers the stock planning we apply to storage class power parts, and our incoming inspection plan is the inspection plan those parts go through on arrival.