Contact Us

TPS25751SRSMR

Brand: Texas Instruments
Texas Instruments TPS25751SRSMR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS25751SRSMR — Power Management & Signal Chain | Superb Automation

TPS25751SRSMR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS25751SRSMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS25751SRSMR: USB Type-C and USB PD 3.1 controller with an integrated 5 V source switch, in a 32 pin QFN

TPS25751SRSMR is a stand alone USB Power Delivery controller that runs the whole Type-C port, negotiates the contract and switches the 5 V path without a host processor in the loop in a VQFN body of 32 pins. It is certified for USB PD 3.1 with a published TID, integrates a 5 V, 3 A, 36 mOhm sourcing switch, and drives external FETs for the high voltage bus path. The S body is a 32 pin QFN at 4 mm by 4 mm, the configuration comes from a web based tool rather than firmware the customer writes, and the part supports programmable power supply in both directions.

Order code and package

TPS25751SRSMR32 pin VQFN (RSM), 4.00 mm by 4.00 mm, 3000 pieces on a large reel, marking 25751S
TPS25751DREFR38 pin WQFN (REF), 4.00 mm by 6.00 mm, the D variant with the integrated 20 V, 5 A, 16 mOhm bi directional load switch
PD certificationUSB-IF PD 3.1, TID 10306 for the TPS25751
Configurationweb based GUI that produces the configuration image, so no firmware development is required
Temperature rangeminus 40 C to plus 125 C, industrial and consumer ports

Electrical parameters that decide the application

Rolesink only UFP ports and dual role DRP ports from the same silicon, selected by configuration
Integrated source switch5 V, 3 A, 36 mOhm, present on both the S and the D variant
High voltage pathdriven through an external FET pair on the S variant, integrated on the D variant
Power path protectionreverse current protection, undervoltage and overvoltage protection, inrush current limiting and slew rate control
Current limitprogrammable, with 1.90 A as one published setting and 10 per cent accuracy on the measurement path
PPSsource and sink, with a programmable interface for the sink side
Liquid detectionmeasured at the Type-C connector with integrated error handling
Charger controlI2C master for a list of TI battery chargers, so the PD contract sets the charge current directly
Power statesActive, Idle and Sleep, which is what keeps a battery product inside its standby budget
Start upslew rate control on the high voltage gate, with settings between 0.35 and 3.8 V per ms

The S variant against the D variant

Package32 pins at 4 mm by 4 mm for the S, 38 pins at 4 mm by 6 mm for the D
High voltage switchexternal FETs on the S, an integrated 20 V 5 A 16 mOhm switch on the D
Source switchthe 5 V 3 A 36 mOhm switch is integrated on both
Pin count differencethe six extra pins on the D are the high voltage path and its sensing
Board areathe D removes two external FETs and their gate components, the S leaves the choice of FET to the customer
Configurationidentical tool and identical image format, so a port can move between the two with a pin change

Points to check before this part goes on a BOM

The S and D variants differ in exactly one place that matters to a purchase order: the high voltage path. The S drives external FETs, the D integrates a 20 V, 5 A, 16 mOhm bidirectional switch. Both integrate the 5 V, 3 A, 36 mOhm source switch. A quote written against the D and filled with the S delivers a board that is missing its bus FETs, and the two parts are not interchangeable on the same land pattern.

The PD 3.1 certification carries a TID, 10306, and that identifier is what a customer checks when they need their own port to pass compliance. Certification belongs to the silicon and the configuration image together, so a PD 3.1 port built from a PD 3.0 controller is a port that fails the newer test even if the connector and the cable are correct.

The configuration image is generated by a web tool rather than written by the customer, which is the single biggest schedule advantage of this part. It also means the configuration is a deliverable that has to be archived with the product, because the tool's output for a given product is not reproducible from the board alone. A program that loses the image file loses the ability to rebuild the port.

The charger control over I2C is what turns a PD contract into a charge current. The controller is a master on the bus and speaks to a defined list of TI chargers, so the negotiation sets the voltage and the current without the host processor. A charger outside that list needs a host bridge, and the list is short enough that it should be checked before the charger is chosen rather than after.

The liquid detection feature measures at the connector and reports through the same configuration path. In a product that can be used outdoors or near water, that is the difference between a port that refuses to negotiate while wet and one that corrodes. The detection is not a substitute for a sealed connector, but it is a cheap second line of defence that lives in silicon rather than in firmware.

The three power states matter more on a battery product than the headline current figures. Active, Idle and Sleep are managed by the controller itself, and the transition thresholds are part of the configuration image. A port that stays in Active because the configuration never allows Sleep drains a battery through a connector that is not even plugged in, and the symptom looks like a cell problem rather than a port problem.

The slew rate control on the high voltage gate has settings from 0.35 to 3.8 V per ms, and the choice trades inrush current against start up time. A fast ramp into a large bus capacitance trips the source supply, a slow ramp makes the port look unresponsive. The published table gives the ranges for a gate capacitance window, and the value has to be selected against the FET actually fitted rather than the reference circuit.

Where this order code fits

It runs the Type-C port in power banks, power tools, cordless appliances, wireless speakers, point of sale terminals and personal care devices, where the port has to negotiate a contract and charge a battery without a processor spending time on USB. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Vendor Consolidation page.

Questions buyers ask

Does the S variant include the high voltage switch? No. The 20 V, 5 A, 16 mOhm bidirectional switch is on the D variant only. The S variant drives external FETs and both variants integrate the 5 V, 3 A, 36 mOhm source switch.

Is custom firmware required? No. The configuration comes from a web based tool and is loaded as an image. That image has to be archived with the product because it cannot be recreated from the board.

Can it source power as well as sink it? Yes, it supports sink only UFP ports and dual role DRP ports from the same silicon, selected by configuration.

What PD revision is it certified for? USB PD 3.1, with TID 10306. That certification is what a customer's own compliance test will look for.

How does it control the battery charger? Over I2C as a master, against a defined list of TI charger parts. The PD contract then sets the charge current without host involvement.

What current limit does the 5 V path use? A programmable setting, 1.90 A is one published value, with 10 per cent accuracy on the measurement path. The exact value is part of the configuration image.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the OEM Procurement page sets out the checks that keep a substitute from failing on the bench.