TPS2511QDGNRQ1
Product Specifications
TPS2511QDGNRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2511QDGNRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2511QDGNRQ1 automotive USB dedicated charging port controller with a current limited power switch
The TPS2511-Q1 is a USB dedicated charging port controller with an integrated current limited switch, in an eight pin HVSSOP body, rated for the automotive temperature range. It provides the D+ and D- divider signature that tells a portable device it is connected to a dedicated charger rather than to a computer, and it provides the VBUS switch with a programmable current limit and a cable compensation input.
The signature is what decides the charging current a phone or tablet will draw. A device that sees a computer port limits itself to 500 mA, while a device that sees a dedicated charging port can pull its full rate. The part generates the divider automatically from the supply, so the board does not need a reference and does not need a microcontroller pin to hold the lines at the right level.
Key parameters taken from the TPS2511QDGNRQ1 document
| Function | USB dedicated charging port controller with an integrated current limited power switch |
| Input range | 4.5 V to 5.5 V on the input pin, which is the USB VBUS window |
| Continuous current | 2.2 A rating for the switch, with the on resistance specified at 2 A of output current |
| On resistance | 80 mOhm typical and 125 mOhm maximum at 2 A |
| Current limit points | 1160 mA typical at 44.2 k, 2300 mA at 22.1 k and 3025 mA at 16.9 k, each with a window around the typical |
| Cable compensation | A CS pin that senses the load current and lifts the output voltage to offset cable drop |
| Data line signature | D+ and D- divider generated inside the part for dedicated charging port detection |
| Data line rating | 35 mA continuous sink and source on the D+ and D- pins, and 5.5 V maximum on those pins |
| Enable | EN pin to turn the switch on and off |
| Protection | Current limit, over temperature protection and short circuit behaviour on the output |
| ESD | 2 kV human body model and 500 V charged device model, with the automotive classification level printed in the document |
| Package | HVSSOP DGN, 8 pins with a thermal pad, 2500 pieces on a large reel and 80 pieces in a tube |
| Moisture and temperature | Level 2 at 260 C with a one year floor life, minus 40 to 125 C |
| Addendum status | TPS2511QDGNRQ1 and TPS2511QDGNQ1 are Active and in Production, marking 2511Q |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The current limit resistor is the part that has to match the port. A 44.2 k resistor gives 1160 mA typical, which suits a single port that has to stay inside a 1.5 A budget after cable and connector losses. A 22.1 k resistor gives 2300 mA for a tablet class port, and 16.9 k gives 3025 mA for a port that is expected to charge a notebook. The three points are printed in the document with their windows, and the limit is a real limit rather than a fold back, so the port delivers its rated current until the limit is reached.
Cable compensation is the feature that makes the difference between a phone that charges at full rate and one that does not. A one metre cable with 28 AWG conductors has enough resistance to drop several hundred millivolts at 2 A, and a device that sees less than 4.75 V at its connector will reduce its draw. The CS pin senses the current and raises the output to hold the voltage at the far end, and the amount of lift is set by the resistor network around that pin.
The divider signature on D+ and D- is generated from the supply, so it is present as soon as the switch is on and does not depend on a controller being awake. That matters in a vehicle, where the port has to work before the infotainment unit has finished booting. The part also holds the data lines inside their rating while the port is off, which is what keeps a device that is plugged into an unpowered port from being damaged by the leakage on those lines.
The 80 mOhm typical on resistance at 2 A dissipates 320 mW, and the 125 mOhm maximum dissipates 500 mW at the same current. In an eight pin HVSSOP with a thermal pad that is a manageable number inside a vehicle cabin, but the pad has to be soldered to copper and the copper has to reach the connector, because the heat path is the only thing between the part and its over temperature protection.
The automotive qualification matters more on this part than on most, because the port is exposed to the outside world. The document prints the ESD classification, the temperature range and the qualification level, and a product that is going into a vehicle should confirm the orderable string against the addendum before releasing a purchase order, since the Q1 suffix is what carries the qualification and the reel size is separate.
- Current limit resistor against the port budget, because the three published points are 1160, 2300 and 3025 mA.
- Cable compensation network against the cable length and gauge the product is expected to work with.
- Thermal pad copper area, since the switch dissipates up to 500 mW at 2 A with the maximum on resistance.
- Data line protection against the ESD level the port will see at the connector, not at the die.
- Enable behaviour during a system reset, because the port has to be off or on in a defined way at power up.
- Orderable string against the addendum, since the reel size and the qualification suffix are separate fields.
Which projects this part fits
This part fits automotive USB charging ports: rear seat charging, centre console ports, telematics units with a service port, and aftermarket head units. It also fits industrial and medical products that need a dedicated charging port with a current limit, because the divider signature and the switch are in one part and the port works without a host controller.
Questions that come up before a purchase order is released
What is the difference between a dedicated charging port and a standard port?
A dedicated charging port presents a divider signature on the data lines that tells the device it may draw more than the 500 mA a computer port allows. The part generates that signature internally, so the board does not need a reference divider of its own.
How is the current limit set?
By a resistor on the ILIM_SET pin. The document gives three points: 44.2 k for 1160 mA, 22.1 k for 2300 mA and 16.9 k for 3025 mA, each with a tolerance window around the typical.
Why does the port need cable compensation?
Because a cable drops several hundred millivolts at 2 A, and a device that sees under 4.75 V at its connector reduces its draw. The CS pin senses the current and lifts the output so the voltage at the far end stays in range.
Can the data lines be left floating?
No. The part drives them to the divider signature while the port is on, and the pins have a 5.5 V rating and a 35 mA current rating that the external protection has to respect.
Is the part AEC-Q100 qualified?
The document prints the automotive qualification and the temperature range for the Q1 rows. The exact grade and the reel size are separate fields, so the orderable string should be confirmed against the current addendum before a purchase order is released.
What happens on a shorted cable?
The switch limits the current and the over temperature protection acts if the fault lasts. A shorted cable is a normal event on a vehicle port and the part is built to survive it, but the connector and the cable have to be rated for the current the port can deliver.
How SUPERB handles this line
We supply the TPS2511QDGNRQ1 on original 2500 piece reels and as 80 piece tubes, with the date code and marking recorded on the packing list. The power management cross reference page lists the USB port controllers we carry by current rating, incoming inspection plan covers the checks we run on reels that go into automotive builds, and kitting service is how we deliver the port controller with its connector and its protection parts against one build.