TPS24751RUVR
Product Specifications
TPS24751RUVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS24751RUVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS24751RUVR: a 12 A protected hot swap circuit with a 3 mOhm FET and an analogue current monitor
TPS24751RUVR is a hot swap controller and power MOSFET in one package that brings a 2.5 V to 18 V bus up at a controlled rate, limits the current while it does, and reports the load current as an analogue voltage in a VQFN body of 36 pins. The RUV body is 36 pins on a 7 mm by 3.5 mm pad, and the FET is inside it at 3 mOhm, which is the reason a 12 A board can be protected without a second package and a gate resistor.
Order code and package
| Catalogue string | TPS24751RUVR, the auto retry member of the two device family |
| Body | VQFN, 36 pins, RUV, 7.00 mm by 3.50 mm |
| Reel | 3000 pieces on a large tape and reel, with the RUVT row at 250 pieces on a small reel |
| Finish and moisture | NIPDAU plating, moisture level 2, 260 C, one year floor life |
| Temperature | minus 40 to 85 C on the addendum rows, although the device is specified to 125 C junction in the body of the document |
| Marking | TPS24751 |
| Document | SLVSC87C, revised December 2018 |
| Safety listing | UL 2367 recognised, file number E339631, which is what a board level protection claim is usually checked against |
Electrical parameters that decide the application
| Bus range | 2.5 V to 18 V, with the internal lockout at 2.32 V rising and 2.22 V falling |
| Continuous current | 12 A, limited by the FET and the thermal path rather than by a control loop |
| On resistance | 3 mOhm typical at 25 C and 3.5 mOhm at 125 C, measured between 1 A and 10 A |
| Current limit | programmable by a resistor on SET, with the vendor quoting accuracy from 10 mA to 12 A, which is a range wide enough to cover a 20 mA housekeeping load and a 12 A board on the same part |
| Current monitor | an analogue output on IMON, with the sense resistor and monitor resistor setting the scale, so the load current can be read by an ADC instead of inferred from a fault pin |
| Fast breaker | a separate short circuit comparator that opens the FET quickly, independent of the timed current limit that allows an overload for a while |
| SOA protection | the gate is regulated so the FET stays inside its safe operating area during start up into a heavy load, which is the failure mode that kills unprotected hot swap circuits |
| Fault timer | 10 uA into an external capacitor, with a four per cent retry duty on the TPS24751 and latch off on the TPS24750 |
| Power good | PGb compares the drain and source of the FET and releases when the difference falls inside a 140 to 340 mV window, which is a real indication that the FET is fully enhanced |
| Fault flag | FLTb, open drain and active low, asserted when the timer has turned the FET off |
| Programmable protection | UV and OV comparators with external dividers, plus a programmable output slew rate through the gate capacitor |
| Thermal | the junction limit is 125 C and the body is 7 mm by 3.5 mm with a pad, so the copper under the pad is part of the current rating |
Latch off against auto retry, and what the monitor output is for
| TPS24750 | the latch off member, which stays off after a fault until the enable pin is cycled |
| TPS24751 | the auto retry member on this page, with a four per cent duty cycle during a persistent fault |
| TPS24751RUVR | the 3000 piece large reel row |
| TPS24751RUVT | the 250 piece small reel row, same device and same moisture level |
| TPS24710 and TPS24720 | relatives without the integrated FET, for a bus that needs a larger external device |
| The choice between the two | auto retry suits a board that has to recover from a transient overload without an operator, latch off suits a board where a repeated retry would damage the load |
Points to check before this part goes on a BOM
The temperature rows disagree between the two halves of the document and that has to be settled before a build is frozen. The electrical table is written over minus 40 to 125 C junction, and the addendum rows print minus 40 to 85 C. For a board that runs at 80 C ambient the junction is well above 85 C at 12 A, so the 125 C figure is the one that governs, and the addendum row is best read as a commercial ambient range rather than a silicon limit.
3 mOhm at 12 A is 432 mW inside the package. On a 7 mm by 3.5 mm body with a pad that is a normal load, and it is the reason the FET is integrated rather than external: an external FET at the same resistance would be a much larger die and a second set of parasitics. The catch is that the copper under the pad carries the heat, so a four layer board with a solid plane is assumed and a two layer board with a thin trace is not.
The current monitor is the feature that separates this part from a simple hot swap controller. IMON produces a voltage proportional to the load current, set by the sense resistor and the monitor resistor, so a system controller can log the current of each slot and detect a load that is drifting before it trips. A fault pin alone tells you that something went wrong; a monitor tells you it is about to.
The four per cent retry duty on the TPS24751 is a thermal decision. A persistent short that retries continuously would heat the FET until the junction limit, so the part retries for a short window and then waits, which keeps the average dissipation near four per cent of the fault value. Latch off avoids the retry entirely and needs someone to cycle the enable, which is right for a slot that a technician can reach and wrong for a sealed enclosure.
Power good on this part is not a voltage comparator on the output. It compares the drain and source of the FET, so it releases only when the FET is fully enhanced and the voltage across it has collapsed. That is a stronger statement than output voltage above a threshold, because a FET that is still in its linear region passes a voltage that looks fine at light load and collapses under load. A power good that ignores the FET state is a power good that lies.
The programmable SOA protection is the part that a plain current limit cannot replace. A current limit holds the current at a value, and into a heavy capacitive load that value flows for a long time while the FET holds the whole bus voltage across it. The gate regulation folds the current back as the drain to source voltage rises, so the FET stays inside its safe area, and the timer decides when to give up. Without that, a start up into a shorted board destroys the FET before the timer expires.
Setting the limit, the timer and the ramp
Three resistors and one capacitor define the behaviour. RSET sets the current limit through the internal sense arrangement, RPROG sets the power limit that the gate regulation works against, and the capacitor on TIMER sets how long an overload is allowed before the FET opens. The vendor application section gives the resistor tables, and the useful discipline is to compute the timer from the worst case start up, not from the steady state.
The ramp is set by the gate capacitor, and the value has to satisfy two constraints at once. Long enough that the inrush into the load capacitance stays below the current limit, short enough that the power good releases inside the system sequencing window. A 100 uF load at 12 V charged in 10 ms draws 120 mA average and 240 mA at the midpoint of a linear ramp, so the limit and the ramp are chosen together rather than one after the other.
What the monitor output actually reports
IMON is a current output into an external resistor, scaled from the sense voltage, so the voltage at the pin is proportional to load current over the whole range rather than only near the limit. That is what makes it useful for a system controller: the same pin that reports 200 mA at idle reports 10 A at full load, and the scale is set once by the two resistors.
The accuracy of that reading is the reason to read the current in the first place. A monitor that is ten per cent out is still useful for trend detection and not useful for billing or for a protection threshold. The vendor quotes the current limit accuracy over 10 mA to 12 A, which is the limit comparator rather than the monitor, and a project that uses the monitor for a hard decision should calibrate it against a known load at the temperature it will run at.
Where this order code fits
This is the slot protection on a server backplane, a RAID enclosure, a base station line card, a plug in module or a fan tray, where a board is inserted into a live bus and has to come up without taking the bus down Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.
Questions buyers ask
How much current can it carry? 12 A continuous with a 3 mOhm FET, and the practical limit is the copper under the pad. 12 A is 432 mW inside the package, which needs a solid plane rather than a trace.
What is the difference between the two parts? TPS24751 retries at a four per cent duty cycle during a persistent fault, TPS24750 latches off until the enable pin is cycled. The reel letter R is the same on both.
Is the current monitor accurate enough for a decision? It is an analogue output scaled from the sense voltage and it is good for trend and load profiling. For a hard threshold, calibrate it at the working temperature, because the limit comparators are the specified function.
Why does the addendum say 85 C when the table says 125 C? The electrical table is written over the junction range and the addendum rows print a commercial ambient range. At 12 A the junction runs well above ambient, so the junction figure is the one that governs.
Is the FET protected during a short at start up? Yes, that is what the SOA regulation and the timer are for. The gate folds the current back as the voltage across the FET rises, and the timer ends the event before the die is damaged.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.