TPS2375PWR-1
Product Specifications
TPS2375PWR-1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2375PWR-1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2375PWR-1 802.3af powered device controller with an integrated pass FET and automatic retry
The TPS2375-1 is the second generation of the eight pin 802.3af powered device controller from Texas Instruments. It contains detection, classification, undervoltage lockout and an integrated pass FET with programmable inrush limiting, in a body that needs no external MOSFET and no controller of its own. The -1 suffix marks the auto retry members of the family, which restart after a fault clears instead of staying latched off.
The part is rated to 100 V on the input pins so it survives cable transients, and the family specification carries a 1.5 V offset above the IEEE 802.3af limits to allow for the two diode drops of the input bridge that makes the powered device polarity insensitive. The power good output is a true open drain pin, so it can be wired to a controller on a different rail.
Key parameters taken from the TPS2375PWR-1 document
| Standard | IEEE 802.3af powered device, with the family limits offset 1.5 V above the standard to allow for the input bridge |
| Input rating | 100 V on VDD, RTN, DET and PG, which is the transient rating rather than the operating point |
| UVLO | 39.3 V nominal turn on for the 802.3af version, 35.1 V for the legacy version, both at 30.5 V turn off |
| Pass FET | Integrated, 1.0 ohm at 300 mA of return current |
| Current limit | 515 mA at a 1 V return pin measurement |
| Inrush limit | 180 mA with a 178 k resistor on ILIM, terminated when the return current falls below 100 percent of the inrush value |
| Detection resistor | 24.9 k, 1 percent, which is the 25 k signature the PSE looks for |
| Classification currents | 2.8 mA at 4420 ohm, 10.6 mA at 953 ohm, 11.3 mA at 549 ohm, 19.5 mA at 357 ohm and 28 mA at 255 ohm |
| Classification thresholds | Lower threshold 13 V, upper threshold 21 V rising |
| Operating current | Return current range 0 to 350 mA, which is the pass FET rating at the top of the 802.3af band |
| Power good | Open drain output, 10 V threshold nominal, 2 mA sink capability |
| Package | TSSOP PW, 8 pins, 2000 pieces on a large reel and 150 pieces in a tube |
| Moisture | Level 1 at 260 C with unlimited floor life on the PW rows |
| Temperature | Minus 40 to 85 C, printed on the addendum rows |
| Addendum status | TPS2375PW-1, TPS2375PWR-1 and their .A and G4 rows are all Active and in Production, marking 2375-1 |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The 1 ohm pass FET is the whole thermal story on this part. At 350 mA it drops 350 mV and dissipates 122 mW, which an eight pin TSSOP can carry at 85 C ambient without a thermal pad as long as the copper around the pins is reasonable. A product that tries to pull 500 mA through it sits at 250 mW and 500 mV of drop, and the drop is on top of the diode bridge drop, so the voltage that reaches the DC-DC converter at the bottom of the PoE band falls faster than the cable loss alone would suggest.
The classification current table is the part most often got wrong in a review. Each class has its own resistor, and the current is measured with the classification regulator active between 13 V and 21 V. A 1 percent resistor is required for compliance, and the document says so directly, because the class window is narrow enough that a 5 percent part can land in the gap between two classes and make the PSE assign the wrong power budget.
Auto retry changes what happens on a fault. When the return current exceeds the 515 mA limit the part turns the pass FET off, and the -1 suffix restarts it after the fault clears rather than staying off until the input is cycled. That behaviour is what a product wants when a downstream converter hiccups, and it is what an operator wants when the same pair is used to power a camera on a pole that they cannot reach.
The power good pin is an open drain output that goes low until the output is within its threshold of the input, and it is the signal a downstream converter should use as its enable. Wiring it to a converter that starts before PG is valid puts the inrush current of the converter on top of the inrush current of the bulk capacitor, which is how a 180 mA inrush limit gets exceeded on a product that passed its own bench test.
The 100 V rating is worth reading as a transient rating. The steady state is 37 V to 57 V, and the 100 V is what the pins survive during the inductive kick of a disconnection. A product with a long cable and a large bulk capacitor can generate a spike well above the steady state, and the input capacitor and the TVS choice belong in the same review as the pass FET rating.
- Class resistor with 1 percent tolerance, chosen against the class the product needs rather than the next one up.
- Inrush limit resistor against the bulk capacitance and the downstream converter start up, not against the steady state load.
- Power good threshold against the enable threshold of the converter it drives.
- Voltage at the converter input at the bottom of the cable and the bottom of the PSE band, with both diode drops included.
- Package dissipation at the load the product actually draws, not at the 350 mA headline.
- Transient rating of the input capacitor and the TVS against the cable length the product is installed on.
Which projects this part fits
This part fits small 802.3af products where an external pass FET would cost more board area than the controller saves: badge readers, door controllers, small sensors, wireless access points, and IP intercoms. It also fits legacy products that need to keep working on a switch that does not implement the newer classification, because the -1 family keeps the 802.3af UVLO points and the legacy member keeps the 35.1 V turn on for older PSE hardware.
Questions that come up before a purchase order is released
What is the difference between the -1 parts and the plain parts?
The -1 suffix marks the auto retry versions, which restart after a fault is removed. The plain members latch off and need the input to be cycled before they conduct again. The UVLO points are the same within a given family member.
Why is a 1 percent classification resistor needed?
Because the class windows are narrow and the PSE reads the current to decide the power budget. A resistor outside 1 percent can put the current in the gap between two classes, and the PSE then either refuses power or assigns a lower class.
How is the inrush limit set?
By a resistor from ILIM to the return rail. With 178 k the inrush limit is 180 mA, and the part leaves inrush mode when the return current falls below the termination percentage of that value.
Can the pass FET be bypassed for higher current?
No. The FET is inside the package and the 350 mA figure is the operating range. A product that needs more current needs a controller with an external FET, not a larger bulk capacitor.
Does the part work with an isolated converter?
Yes, the power good output and the return pin are the interface to the converter, and the converter's own isolation is separate from the PoE interface.
What happens if the PSE removes power during operation?
The UVLO comparator turns the pass FET off at 30.5 V, which is above the point where the PSE is required to maintain power, so the product drops its load before the rail collapses.
How SUPERB handles this line
We supply the TPS2375PWR-1 on original 2000 piece reels and as 150 piece tubes, with the date code and marking recorded on the packing list. The power management cross reference page lists the 802.3af interfaces by current rating and package, incoming inspection plan describes the checks we run on the class and detection resistors before a reel goes to a line, and kitting service is how we deliver the interface with its bridge and its class resistor against one build.