Contact Us

TPS23758RJJR

Brand: Texas Instruments
Texas Instruments TPS23758RJJR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS23758RJJR — Power Management & Signal Chain | Superb Automation

TPS23758RJJR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS23758RJJR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS23758RJJR 802.3at powered device interface with a no-opto synchronous flyback controller for 13 W products

The TPS23758 is the 13 W member of the Texas Instruments PoE powered device family. It combines the 802.3at interface, the hotswap MOSFET and a current mode flyback controller built for synchronous rectification, and its own document describes the typical application as a 13 W Type 1 powered device. The pass FET inside the interface has about 0.5 ohm of resistance, which is enough for the 350 mA a 13 W load draws at the low end of the 37 V to 57 V band.

The controller side uses primary side regulation from an auxiliary winding, so the isolated output needs no optocoupler and no shunt regulator. It drives a synchronous rectifier on the secondary, supports more than one output, and offers spread spectrum frequency dithering plus slew rate control to keep the EMI filter small. Non isolated products can use the same part in buck topology, which makes it usable on a single board platform that ships as both a PoE and a 12 V adapter product.

Key parameters taken from the TPS23758RJJR document

PoE standardIEEE 802.3at, Type 1 powered device, 13 W class of product in the vendor application
Hotswap pass FET100 V rated, about 0.5 ohm typical on resistance at 25 C, integrated
Hotswap current limit550 mA typical with a 405 to 800 mA window, pulsed measurement at 1.5 V on the return pin
UVLO35.5 V rising with a 34.7 to 36.7 V window, which is the 802.3at turn on point
Classification current10.6 mA typical with a 68.1 ohm resistor, 9.9 to 11.3 mA window
Classification regulatorTurns on at 12.1 V typical rising and off at 22 V typical rising
Switching frequency248 kHz typical with a 223 to 273 kHz window, set by a resistor on FRS
Current limit turn off delay41 ns typical with a 25 to 60 ns window
RegulationPrimary side regulation from an auxiliary winding, no optocoupler, synchronous rectifier drive on the secondary
Multiple outputsSupported, which is why the family is used on products that need 5 V and 3.3 V from one isolated stage
PackageVSON RJJ, 23 pins, 3000 pieces on a large reel and 250 pieces on a small reel, NIPDAUAG finish
MoistureLevel 2 at 260 C with a one year floor life on the RJJ rows
TemperatureMinus 40 to 125 C, printed on both the addendum rows and the device information table
Addendum statusTPS23758RJJR, its .A row, the 250 piece small reel row and TPS23758RJJT are all Active and in Production

Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.

Where the numbers matter in a real build

The 550 mA current limit is the number that decides whether a 13 W product can start into its own bulk capacitance. A 13 W load at 37 V draws 350 mA, so the typical limit leaves 200 mA of headroom for the ramp, and the bottom of the window at 405 mA leaves only 55 mA. A product with a 100 microfarad bulk capacitor and a 20 ms inrush window will pull more than that, which is why the inrush limit is a separate row and why the inrush termination percentage matters: the part leaves inrush mode when the return current falls below the termination threshold, not after a fixed time.

Primary side regulation with a synchronous rectifier is a combination that needs care on the transformer. The auxiliary winding has to see the same flux as the secondary, and the synchronous rectifier has to be driven with enough dead time that the body diode does not conduct during the commutation. The document provides a gate drive output for the secondary FET and quotes the switching frequency window, and a transformer that is wound for a diode rectifier usually needs the secondary turns checked before the same core is reused.

Spread spectrum dithering and slew rate control are the two features that decide the size of the EMI filter. On a 13 W product the filter is often the largest single block of the bill of materials after the transformer, and a part that modulates its own switching frequency can drop a common mode choke size. The dithering is programmable, so the modulation depth and rate can be set to stay clear of the conducted emissions band the product has to pass.

The part supports buck topology for non isolated products, which is unusual in a PoE interface and useful on a platform that ships two versions. The same board can carry the isolated flyback for the PoE version and a buck stage for the adapter version, with the same controller and the same inductor family, which keeps the qualification work to one controller instead of two.

The 23 pin VSON body has a thermal pad and the junction to ambient figure depends on the copper under it. At 13 W with 85 percent efficiency the part dissipates under 2 W in total, most of it in the pass FET while the converter runs, so the pad is not the limiting factor in a normal enclosure, but a sealed housing with no airflow is where the thermal margin gets used up.

  • Hotswap current limit against the start up current of the actual load, not against the steady state figure.
  • Inrush termination point on the return current, since the part leaves inrush mode on a current threshold rather than a timer.
  • Transformer turns ratio and auxiliary winding coupling, which decide the regulation accuracy with primary side feedback.
  • Secondary synchronous rectifier dead time and gate drive, because a body diode that conducts during commutation shows up as heat and as a common mode emission.
  • Dithering depth and rate against the conducted emissions band the product has to pass.
  • Thermal pad copper area in the enclosure the product actually ships in.

Which projects this part fits

This part fits 13 W powered devices: single radio access points, fixed dome cameras, VoIP desk phones, badge readers and building controllers. It also fits products that need two isolated outputs from one PoE feed, because the controller supports multiple outputs from the same primary side feedback loop. Where the product needs the full 25.5 W the larger member of the family is the right choice, and where the product is fed from an adapter rather than from Ethernet the same controller can run in buck topology.

Questions that come up before a purchase order is released

Why is the pass FET resistant to 100 V?

Because the interface has to survive the cable transients that appear on an Ethernet pair, including the inductive kick when a PSE port is disconnected under load. The 100 V rating is on the FET and on the input pins, and the recommended operating range is what the part runs at continuously.

What is the difference from the higher power member?

The current limit, the on resistance and the intended power class. This part is quoted for a 13 W Type 1 application with a 550 mA limit, while the larger member covers 25.5 W with a 0.925 A limit and a lower resistance FET.

Can it drive a secondary synchronous rectifier?

Yes, and that is the reason the family quotes its efficiency at the top of the load range. The gate drive output for the secondary FET is part of the controller, so the rectifier does not need its own sense and timing circuit.

Does it need an optocoupler?

No. Feedback comes from an auxiliary winding on the primary side. A product that needs tighter cross regulation than primary side feedback can give should either couple the windings more tightly or use the secondary side regulated mode of the larger member.

What package options exist?

The RJJ VSON with 23 pins, on a 3000 piece large reel and a 250 piece small reel. Both rows are Active in the current addendum, and the .A rows carry the same reel sizes.

Can it work without Ethernet?

Yes, the controller also runs a buck topology for non isolated products, so the same part can serve an adapter fed version of the same board.

How SUPERB handles this line

We supply the TPS23758RJJR on original reels, both the 3000 piece large reel and the 250 piece small reel, with the date code and marking recorded. The power management cross reference page groups the PoE interfaces we carry by power class, component lead time solutions is where we list the current allocation on the PoE family, and kitting service is how we ship the interface, the transformer and the secondary rectifier as one kit against a build.