TPS2359RHHR
Product Specifications
TPS2359RHHR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2359RHHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2359RHHR dual slot AdvancedMC controller with I2C programmable limits in the thirty six pin VQFN
The TPS2359 is a hot plug controller for two AdvancedMC slots on an ATCA carrier board. It handles the 12 V and 3.3 V rails for both slots, with the 3.3 V channels integrated and the 12 V channels driving external FETs through external sense resistors. Fault times and 12 V current limits are programmable over I2C, and the device reports per channel status through the same bus.
The part exists because an AdvancedMC slot has a narrow current limit window that a discrete controller cannot meet with a fixed threshold. The 3.3 V limits are set inside the device to the levels the specification requires, and the 12 V limits are programmed by four I2C bits that scale the threshold, with a separate fast trip comparator that acts in microseconds rather than milliseconds. Two slots in one body also means one I2C address pair and one set of status bits for a carrier that may hold several cards.
Key parameters taken from the TPS2359RHHR document
| Slots | Two AdvancedMC slots, each with a 12 V and a 3.3 V channel |
| 3.3 V channels | Integrated FETs with factory set current limits that meet the AdvancedMC requirement |
| 12 V channels | External FETs and external sense resistors, with a threshold set by the sense resistor and the I2C scaling bits |
| 12 V current limit adjust | Four bits per channel, scaling the threshold from 25 per cent to 100 per cent of the full value |
| Full scale threshold | 100 mV across the sense resistor at the top of the I2C range |
| Fast trip threshold | 170 mV minimum, 195 mV typical and 225 mV maximum, which is the comparator that acts before the current limit loop |
| Interlock | 3 V and 12 V interlock for AdvancedMC compliance, so a slot cannot be powered in the wrong order |
| Reporting | Power good, fault and FET status bits per channel over I2C, with separate latch bits for overcurrent and fast trip |
| Addressing | A0 to A2 pins set the bus address |
| ORing | 3.3 V and 12 V FET ORing for MicroTCA arrangements |
| Package | VQFN RHH thirty six pins |
| Packing | 2500 pieces on a large reel, moisture level 3 with a 168 hour floor life |
| Temperature | Minus 40 to 85 C, marking TPS2359 |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The two current paths behave differently and should be treated as two separate circuits. The 3.3 V channels have their FETs inside the package, so the limit is set by the vendor and the board only has to provide the copper. The 12 V channels drive external FETs and measure across external sense resistors, so the limit is a board decision that has to be made with the FET SOA in front of it. A carrier board that copies a sense resistor value from another board without checking the FET will either trip early on a legitimate load or fail to protect the FET during a fault, and the I2C bits only scale the threshold around the resistor value.
The four scaling bits are a range, not a set of absolute limits. They adjust both the current limit and the fast trip threshold together, and clearing all four reduces both to a quarter of the full value. That is useful during bring up, because a card can be started with a low limit and the limit raised once the load is known. It is also a trap during production, because a board that ships with the default bits in the wrong state has a quarter of the intended fault current, and the fault only appears when a real short occurs.
The fast trip comparator is what protects the external FET. It works in microseconds and acts at 170 to 225 mV, which is several times the normal limit threshold, so it only responds to a hard short. A slow overload is left to the current limit loop and the fault timer, which lets a card ride through a legitimate load step. The latch bits tell the difference after the fact: one bit records that the current limit was reached, another records that the fast trip fired, and a maintenance report can use the two to tell an overload from a short.
The moisture level is worth noting before a production schedule is set. The body is level 3 with a 168 hour floor life, which means a reel that sits on a line for more than a week needs a bake or a dry store. A carrier board that runs this part on a high mix line should plan the storage, because a level 3 part that has absorbed moisture can crack during reflow, and the failure appears as a batch of boards with a shorted pin rather than as a single bad unit.
- The 12 V sense resistor against the FET SOA, since the two together set what the channel survives.
- The I2C scaling bits at power up, because the default state may not be the production limit.
- The address straps for both devices on a carrier that uses more than one.
- The interlock between 3 V and 12 V, because an AdvancedMC slot that powers in the wrong order fails specification.
- The level 3 floor life, which decides whether a reel needs a bake before it goes to the line.
- The thermal path of the 36 pin body, because the integrated 3.3 V FETs dissipate in the package.
Which projects this part fits
This part fits ATCA carrier boards and MicroTCA power modules, base station shelves that carry AdvancedMC cards, and any chassis where two mezzanine slots have to be powered and monitored from one controller. It also fits systems that need per slot current telemetry over a bus rather than a fixed fault flag, because the status bits and the programmable limits give the shelf controller a way to report which card drew what.
Questions that come up before a purchase order is released
Can the current limits be changed while the card is running?
The bits are writable over I2C and the document describes them as part of the control register set. The safe practice is to set the limit before the slot is enabled, and to treat a change during operation as a maintenance action rather than something the firmware does routinely.
What is the difference between the current limit and the fast trip?
The current limit is a loop that holds the current at the threshold, and the fast trip is a comparator that turns the channel off in microseconds at a much higher threshold. The two latch bits record which one acted, so a fault report can distinguish an overload from a short.
Does the part need external FETs on the 3.3 V rail?
No. The 3.3 V channels have their FETs inside the package and the limits are factory set. Only the 12 V channels need external FETs and sense resistors.
How many devices fit on a bus?
The three address pins give eight addresses, which is enough for a full shelf of carriers. The straps have to be tied high or low, and the carrier backplane normally sets them from the slot position.
What happens if the 3.3 V rail is missing?
The interlock prevents the 12 V channel from being enabled in the wrong order. The exact sequence is in the functional description, and a chassis that powers the two rails from separate supplies has to follow it.
How SUPERB handles this line
We supply the TPS2359RHHR on original 2500 piece reels with the moisture level 3 handling rule applied in our warehouse, and we record the marking TPS2359 at goods in. The power management cross reference page lists the hot swap and shelf controllers we carry, incoming inspection plan covers the bake and floor life record a level 3 reel needs, and last time buy and LTB planning is where we track the lifecycle of parts that sit on long life telecom platforms.