TPS2330IPWR
Product Specifications
TPS2330IPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2330IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2330IPWR single channel hot swap controller with circuit breaker and power good in the fourteen pin TSSOP
The TPS2330 is a hot swap controller for a single high side N channel MOSFET on a 3 V to 13 V rail. It drives the gate with a controlled slope, measures the current across an external sense resistor, trips a circuit breaker when the current stays above a threshold for longer than a capacitor set time, and reports power good and fault. The enable is active low on this member and the body is the fourteen pin TSSOP.
It is the part a board uses at the input of a plug in card, or at the input of a slot that a user can insert under power. The controller holds the MOSFET off until the rail is valid, ramps the gate so the inrush into the card capacitance is a known slope, and then watches the sense voltage. If a fault lasts longer than the timer allows, the gate is pulled down and the fault output is latched until the enable is cycled, which is what stops a board from retrying into a short forever.
Key parameters taken from the TPS2330IPWR document
| Input range | 3 V to 13 V on the main input, with a second supply pin for the internal regulator at 3 V to 5.5 V |
| Gate drive | Internal regulator provides the gate supply so a 3.3 V logic level FET can be driven from a 12 V rail |
| Circuit breaker threshold | Set by a resistor on ISET, printed as 19 mV typical at 400 Ohm, 50 mV at 1 kOhm and 73 mV at 1.5 kOhm, so the threshold scales with the resistor |
| Fault current | The load current at which the breaker trips is the ISET threshold divided by the sense resistor, so a 5 mOhm sense with 50 mV gives 10 A |
| Timer | The TIMER pin charges at 50 microamp typical to a 0.5 V threshold, so the delay is about 10 milliseconds per microfarad |
| Timer threshold | 0.4 V minimum, 0.5 V typical and 0.6 V maximum, which is a 20 per cent window on the fault time |
| Enable | Active low on this member with an internal pull up of 100 to 300 kOhm, 2 V maximum for a high and 0.8 V minimum for a low |
| Supply current | 1 mA maximum operating and 5 microamp maximum in standby, which is the figure that matters on a battery rail |
| Gate clamp | The gate to discharge clamp holds the gate source voltage inside the FET rating |
| Reporting | Power good with a filter against short excursions, and a latched fault output |
| Ramp control | The gate rise time is set by the gate capacitor: the document prints about 1 millisecond at 10.8 V input with a 1 nF gate capacitor |
| Package | TSSOP PW fourteen pins |
| Packing | 2000 pieces on a large reel, NIPDAU finish, moisture level 1 with unlimited floor life, marking PD2330I |
| Temperature | Minus 40 to 85 C |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The circuit breaker threshold is a voltage, not a current, and the sense resistor is what turns it into amps. The document prints the ISET threshold for three resistor values, 19 mV at 400 Ohm, 50 mV at 1 kOhm and 73 mV at 1.5 kOhm, and the relation is close to 50 mV times the resistor over 1 kOhm. A board that copies a 50 mV threshold from one board to another but changes the sense resistor from 5 mOhm to 2 mOhm has doubled its fault current without touching the ISET network. That is the single most common mistake we see on this class of controller, and it is invisible in a drawing review unless the two resistors are read together.
The timer is the other half of the protection and it is set by a capacitor, not by a resistor. The pin charges at 50 microamp into a 0.5 V threshold, so the delay is about 10 milliseconds per microfarad, and the threshold itself has a 20 per cent window from 0.4 V to 0.6 V. A board that wants a 1 millisecond transient tolerance fits 100 nF and accepts that the trip time varies with the capacitor tolerance and the threshold window. A board that wants to ride through a 10 millisecond load step fits 1 microfarad. The point of the timer is to let short current spikes through without tripping, which is what a disk drive spin up or a fan start looks like.
The active low enable on this member is a source of confusion when the active high sibling is used on the same product family. Both parts share a document and a pin out, and the only difference is the polarity of the enable pin, which the document calls out in the pin description and in the electrical table. A board that mixes the two members across revisions needs the firmware to know which one is fitted, or a strap that inverts the signal, because an active low part held low is off and held high is on, and the opposite of what the code assumes leaves the rail dead.
The 5 microamp standby current is what makes this part usable on a battery product, and the 1 mA operating current is what the same product has to budget when the card is on. Neither number is large, but the internal gate supply means the controller is not free: it has to generate a gate voltage above the rail, and that charge pump runs continuously while enabled. On a 12 V rail the gate supply is a small load and on a 3.3 V rail it is a slightly larger one, and the document prints the operating current as a single maximum that covers both.
- The ISET resistor and the sense resistor together, since the threshold is a voltage and the current is set by both.
- The timer capacitor against the real load step the rail sees, because the 20 per cent threshold window is part of the delay.
- Enable polarity, because this member is active low and the sibling is active high.
- Gate capacitor value, since the ramp controls the inrush and the ramp is set by that capacitor.
- Standby current of the whole input circuit, including the enable pull up.
- The FET gate charge, because the controller has to drive it within the ramp time it is asked for.
Which projects this part fits
This part fits plug in cards on 12 V and 3.3 V backplanes, hot swap slots in telecom and industrial chassis, fan trays and disk carriers where a module is inserted under power, and any board that has to limit its own inrush to a backplane specification. It is also a good fit for a product that needs a latched fault rather than an automatic retry, because the fault output stays asserted until the enable is cycled.
Questions that come up before a purchase order is released
What happens after a fault?
The gate is pulled down and the fault output latches. The part does not retry on its own, so the system has to cycle the enable to bring the rail back. That is the behaviour that stops a board from sitting in a hiccup loop against a permanent short.
Does the timer reset if the overcurrent goes away?
The timer capacitor is discharged when the current falls back below the threshold, so a short excursion is tolerated and a long one trips. The document describes the charge and discharge paths on the TIMER pin in the functional description.
Can the part drive a logic level FET from a 12 V rail?
Yes. The internal regulator produces the gate supply, so a FET with a 4.5 V or 10 V gate rating can be used on a 12 V rail. The gate clamp keeps the gate source voltage inside the FET rating at all times.
What is the difference to the TPS2331?
Only the enable polarity. This member is active low and the TPS2331 is active high, and the same document covers both. The pin out and the protection behave identically.
Does it need an external sense resistor?
Yes. The current is measured across a resistor between the input and the sense pins, and the ISET resistor sets the threshold voltage. The accuracy of the trip point depends on both resistors and on the offset of the sense amplifier, which the document prints as a bias current of 5 microamp maximum.
How SUPERB handles this line
We supply the TPS2330IPWR on original 2000 piece reels with the marking PD2330I checked at goods in, and we stock the active high sibling so a board revision can change polarity without a new part number search. The power management cross reference page lists the hot swap controllers we carry by voltage and feature set, component lead time solutions covers the case where the exact body is short and a substitute has to be qualified, and supplier quality audit is the process we follow when a customer wants the reel provenance documented.