TPS22995RZGR
Product Specifications
TPS22995RZGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22995RZGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22995RZGR: a 3.8 A load switch with 18 milliohm of on resistance and an adjustable rise time in a six pin WQFN
TPS22995RZGR is a single channel load switch with an N channel MOSFET, a charge pump driven bias rail and a timing pin that sets the output slew rate with one capacitor in a WQFN-HR (RZG) body of 6 pins. The switch runs from 0.4 V to 5.5 V on the input with a separate 1.5 V to 5.5 V bias rail, carries 3.8 A continuous at 18 milliohm typical, pulls the output to zero through a 100 ohm quick discharge when it turns off, and holds 10 microamp of quiescent current in the on state and 0.1 microamp in the off state. The RZG body is 1.50 mm by 0.75 mm.
Order code and package
| TPS22995RZGR | WQFN-HR (RZG) body, 6 pins, 1.50 mm by 0.75 mm on a 0.5 mm pitch, 3000 pieces on a large reel, moisture level 1 at 260 C with unlimited floor life, marking 6, active status in the addendum dated 18 August 2026 |
| TPS22995RZFR | the same die in the smaller RZF body, 1.25 mm by 0.85 mm on a 0.4 mm pitch, same 3000 piece reel, marking 7 |
| .A suffix rows | both bodies are repeated with an .A suffix and the finish and packing are read on the row, because the suffix does not change the body |
| Body choice | the two bodies are the same silicon with a different pin pitch, so the land pattern and the stencil aperture set follow the body named on the string |
| Temperature | minus 40 C to 125 C on both bodies, which is the range the on resistance table is written against |
| Marking | 6 on the RZG rows and 7 on the RZF rows, which is the only visual difference on a reel |
| Bias rail | the bias pin has its own supply range from 1.5 V to 5.5 V and is separate from the input, which is what makes a 0.4 V input possible |
Electrical parameters that decide the application
| Input voltage | 0.4 V to 5.5 V on the switch input, which covers a 1.2 V, 1.8 V, 3.3 V or 5 V rail without a second part number |
| Bias voltage | 1.5 V to 5.5 V on the bias pin, and the bias rail is what drives the gate above the input to turn the N channel switch fully on |
| Continuous current | 3.8 A maximum, with the on resistance and the copper under the package setting the practical figure |
| On resistance | 18 milliohm typical at 25 C with a 5 V input, 24 milliohm over minus 40 C to 85 C and 27 milliohm maximum, and 17 milliohm typical at 3.3 V, 1.8 V, 1.2 V and 0.8 V inputs with 23 milliohm over temperature and 25 milliohm maximum |
| Quiescent current | 10 microamp typical in the on state and 0.1 microamp typical in the off state, which is what makes it usable on a battery rail that is switched rather than regulated |
| Quick output discharge | 100 ohm typical from the output to ground when the switch turns off, so a rail goes to a known state instead of floating |
| Rise time | set by a capacitor on the CT pin, and with the pin open the rise time is 127 microseconds at a 5.5 V bias and a 5.5 V input into a 100 ohm load with a 0.1 microfarad capacitor, which produces 1.59 A of inrush |
| Enable thresholds | 1.5 V to 5.5 V for a logic high and 0 V to 0.35 V for a logic low, so a 1.8 V GPIO drives it directly |
| Enable pulldown | 500 kilohm typical from the enable pin to ground when the pin is low, which holds the switch off if the driving line floats, and 25 nanoamp maximum of input current when the pin is high |
| Thermal shutdown | an internal shutdown that protects the switch when the junction rises, and the part returns to operation once it cools |
| Timing pin | the CT pin can control the slew rate through a capacitor to ground, and the relationship between the capacitor and the rise time is given by the inrush equation in the document |
| Inrush limit | the rise time is chosen so that the inrush current stays under the load's own limit, which is the whole reason the timing pin exists |
Family variants and how they differ
| RZG and RZF | the same silicon in a 1.50 mm by 0.75 mm body on a 0.5 mm pitch and a 1.25 mm by 0.85 mm body on a 0.4 mm pitch, so the smaller body needs a finer stencil and a different land pattern |
| Bias separation | the bias pin is separate from the input, so the switch can pass a rail below 1.5 V while the bias comes from a 3.3 V housekeeping rail |
| Discharge | the 100 ohm quick discharge is internal and cannot be disabled, which matters on a rail that is deliberately held up by a second source |
| Enable pulldown | the smart pulldown holds the switch off when the enable line floats, so a board without a pull down resistor still comes up in the off state |
| Marking | 6 and 7 are one character codes that separate the two bodies on the reel |
| Relative | the part is a load switch rather than an eFuse, so it limits inrush by slew rate rather than by current, and it has no current limit of its own |
Points to check before this part goes on a BOM
The bias rail is not optional. The switch needs 1.5 V or more on the bias pin to drive the gate above the input, so a board that ties the bias to a 1.2 V rail will not turn the switch fully on and the 18 milliohm figure will not apply.
The rise time is the inrush control. With the timing pin open the rise time is 127 microseconds and the inrush into 0.1 microfarad is 1.59 A, so a load with a large capacitor needs a timing capacitor rather than the default.
The quick discharge cannot be switched off. It pulls the output down through 100 ohm whenever the enable line goes low, which is what a card slot or a module reset wants and what a diode ORed rail does not.
On resistance is quoted at 25 C and over temperature. The 18 milliohm typical becomes 24 milliohm over minus 40 C to 85 C at a 5 V input, and the difference is the number to use for a worst case voltage drop calculation.
The part has no current limit. It is a switch, so the only protection against an overload is the thermal shutdown, and the upstream supply has to be the thing that limits the fault current.
Choosing the timing capacitor for a real load
The inrush into a load capacitor is the capacitance times the voltage change divided by the rise time. A 47 microfarad load charged to 5.5 V in 1292 microseconds draws about 200 mA, which is the worked example in the document, and the same equation applies to any other combination.
Longer rise times lower the inrush but extend the time the switch is in its linear region, where the dissipation is highest. The compromise is usually a rise time just long enough that the upstream supply does not current limit, and the timing capacitor is chosen from the curve rather than from the open pin default.
Where this order code fits
The part suits a rail that has to be switched rather than regulated: a card slot, a cellular module, a camera sensor or a USB port, where 3.8 A is the ceiling and the inrush has to be controlled. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can it switch a 1.2 V rail? Yes. The input range starts at 0.4 V and the bias pin can be fed from a higher rail, so a 1.2 V load is switched with the bias at 3.3 V. The on resistance at 1.2 V is 17 milliohm typical.
What happens if the enable pin floats? The internal 500 kilohm pulldown holds the switch off, so the rail stays down. That is deliberate, and it removes the external resistor from a board that cannot guarantee the driving line is defined at power up.
Does it protect the load from a short? No. There is no current limit, only thermal shutdown, so a short pulls whatever the upstream supply can deliver until the junction temperature trips the switch off.
How do the two bodies differ? Only in size and pin pitch. The RZG is 1.50 mm by 0.75 mm on a 0.5 mm pitch and the RZF is 1.25 mm by 0.85 mm on a 0.4 mm pitch, and the marking changes from 6 to 7. The electrical behaviour is the same.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.