Contact Us

TPS22995RZFR

Brand: Texas Instruments
Texas Instruments TPS22995RZFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22995RZFR — Power Management & Signal Chain | Superb Automation

TPS22995RZFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22995RZFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22995RZFR: 5.5 V, 3.8 A load switch, 18 milliohm, adjustable rise time, WQFN-HR

TPS22995RZFR is a single channel load switch that puts one N-channel FET between a supply and a load, with the gate driven from a separate bias rail and the ramp rate set by a capacitor on the CT pin in a WQFN-HR body of 6 pins. The input works from 0.4 V to 5.5 V while the bias pin takes 1.5 V to 5.5 V, so the switch can pass a rail that is lower than the voltage used to drive its gate. On resistance is 18 milliohm typical at a 5 V bias, which puts the conduction loss at about 260 mW at the full 3.8 A and about 18 mW at a 1 A load. Rise time is set by a capacitor from CT to ground, so inrush into a large output capacitance is a component choice rather than a fixed number.

Order code and package

TPS22995RZFRActive, WQFN-HR (RZF) body, 6 pins, 3000 pieces on a 180 mm reel
TPS22995RZFR.AActive, same body and same 3000 piece reel, material row printed at MSL Level-1-260C-UNLIM
TPS22995RZGRActive, the same silicon in the RZG body with 0.5 mm pin pitch instead of 0.4 mm, also 3000 pieces
Temperature rangeminus 40 to 125 degrees, characterised over free air temperature
Marking and packingthe reel is 180 mm wide with an 8 mm tape, quadrant Q1

Electrical parameters that decide the application

Input voltage0.4 V to 5.5 V on VIN, 1.5 V to 5.5 V on VBIAS
Continuous current3.8 A maximum
On resistance18 milliohm typical at a 5 V bias, 20 milliohm at 25 degrees for a 1.2 V or 1.5 V input, 33 to 37 milliohm at 125 degrees
Quiescent current10 microamp with the switch on, 0.1 microamp with the switch off
Enable pin25 nA maximum input current when ON is above VIH, 500 kilohm pulldown when ON is below VIL
Quick output discharge110 ohm at 25 degrees, 150 ohm over the full range
Thermal shutdown150 degrees minimum, 170 typical, 190 maximum, 20 degrees of hysteresis
Timing with a 1000 pF CT capacitorabout 0.8 ms of delay, 2.0 ms of rise, 1.1 ms of fall at a 5 V bias

Family variants and how they differ

TPS22995RZFR0.4 mm pitch body, the string on this page
TPS22995RZGRsame die, 0.5 mm pitch, use it when the stencil cannot hold a 0.4 mm pitch
CT pinsets the ramp, leave it open for the fastest rise the part allows
ON pinactive high, can be driven from a 1.2 V logic output because of the 500 kilohm pulldown
QODinternal, so the output falls to zero when the switch turns off instead of floating

Points to check before this part goes on a BOM

The bias rail is the part most people miss. VIN can go down to 0.4 V, but the gate driver needs at least 1.5 V on VBIAS, and the resistance numbers in the front page assume a 5 V bias. A board that ties VBIAS to a 3.3 V rail gets a working switch with a higher resistance than the headline figure, and a board that ties VBIAS to VIN on a 1.2 V rail gets a switch that never turns on properly. The two pins exist to be fed separately.

Rise time is a capacitor choice, not a fixed specification. With a 1000 pF timing capacitor the ramp takes about 2 ms, and the delay before it starts is about 0.8 ms. Removing the capacitor gives the fastest edge the internal circuit allows, which is the wrong answer for a board with a large bulk capacitor on the load side: the inrush becomes a current step limited only by the FET and the supply impedance, and a 5 V adapter with a 2 A limit will fold back. Size CT against the load capacitance and the inrush the upstream supply can deliver.

The 3.8 A rating is a package limit, not a wire limit. In the RZF body the thermal path is the copper under the part. At 3.8 A and 18 milliohm the conduction loss is 260 mW, and the junction rise depends entirely on the board. A ground pour with vias under the body carries it; a part sitting on a narrow trace with no pour will reach the thermal shutdown threshold and cycle. The trip point is 150 to 190 degrees with 20 degrees of hysteresis, so a marginal board shows up as an intermittent drop out rather than a dead switch.

Quick output discharge is 110 ohm, which is a bleeder and not a brake. It pulls the output to zero when the switch is off, so a load that must not float does not float. It will not discharge a 1000 microfarad bank in a millisecond: the time constant with that bank is about 110 ms to reach a third of the starting voltage. A board that needs a fast collapse on power down has to add its own discharge path.

The enable input is tolerant of slow edges and of logic below the supply. The pulldown is 500 kilohm, so a 1.2 V logic output can hold it high without a level shifter, and the pin draws 25 nA at most when it is high. That matters on a board where the switch sits on a 5 V rail and the controller runs at 1.8 V, because no extra gate is needed and no current is wasted holding the switch on.

Leakage with the switch off is 0.1 microamp, and that is what a battery sees. A load switch in a portable product is judged by the off state, not the on state. At 0.1 microamp the part adds almost nothing to shelf drain, but leakage through the load and through the pulldown network on the enable pin often dominates. The number to quote a customer is the whole branch, not the part alone.

The 5.5 V ceiling excludes a 12 V bus and a 5 V bus with a hot plug transient. A 5 V rail with a 10 per cent tolerance reaches 5.5 V exactly, so there is no margin for a surge, and a hot plug event on a USB connector routinely overshoots. Boards that see that event need a higher voltage switch or a clamp in front. This part is right for a battery rail, a 3.3 V rail and a 5 V rail that is already protected.

Two orderable strings differ only in the moisture statement. RZFR and RZFR.A ship the same silicon on the same 3000 piece reel, and the difference is the material row: one is printed at MSL Level-1-260C-UNLIM, which means no floor life clock on the line, and the other depends on the base row being read. A customer who files a material declaration against one string and receives the other has a paperwork problem even when the part is identical, so state which row is shipping on the offer.

What to confirm before this part goes on a purchase order

Give the bias voltage as well as the load rail. The resistance and the maximum current both depend on VBIAS, and a quote that only names the 5.5 V input range hides the number that decides the thermal margin.

State the load capacitance and the inrush limit of the upstream supply, because the timing capacitor is chosen against them and the part ships without a capacitor fitted on CT.

Where this order code fits

It sits between a battery or a 3.3 V rail and a subsystem that has to be switched off entirely, such as a radio module, a display backlight driver or a sensor board on a shared bus, where the off state leakage and the inrush at turn on both matter. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can this switch pass a 1.8 V rail when the bias is 3.3 V? Yes. The input goes down to 0.4 V and the bias only has to be above 1.5 V, so a 1.8 V load rail with a 3.3 V bias is inside the specification. The on resistance is then the number for the lower input voltage, 31 to 34 milliohm across the temperature range, not the 18 milliohm headline.

Does it protect the load from a short circuit? No. There is no current limit in this part, only thermal shutdown. A short pulls whatever the supply can deliver until the junction reaches the trip point, and the switch then cycles in and out of shutdown. A rail that needs a defined current limit needs a protected switch or an external sense resistor.

What sets the turn on delay? The CT capacitor sets the ramp and the internal circuit adds a fixed delay of roughly 0.8 ms before the ramp starts. Both appear in the switching table with a 1000 pF capacitor, so a timing budget taken from that row is repeatable from part to part.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.