TPS22975DSGR
Product Specifications
TPS22975DSGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22975DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22975DSGR 6 A load switch with 16 mOhm on resistance, thermal shutdown and a 5.7 V bias rail
The TPS22975 is a 6 A single channel load switch with a typical on resistance of 16 mOhm, an input range from 0.6 V up to the bias rail, and a bias range up to 5.7 V. The DSG body is the same 2 mm by 2 mm eight pin WSON used across this family, and the part is specified to 105 C ambient, which puts it in the group a telecom or industrial board can use without derating the whole rail.
Two things separate it from the 4 A member below it. The first is the on resistance, 16 mOhm typical against 22 mOhm, which changes the drop budget on a 5 A load from 110 mV to 80 mV. The second is a thermal shutdown circuit at 160 C with 20 C of hysteresis that turns the switch off when the die overheats and turns it back on when it cools, which is the only overcurrent protection the part has and is worth understanding before it is relied on.
Key parameters taken from the TPS22975DSGR document
| Rated continuous current | 6 A through one switch, with the pad soldered to a copper area |
| Input range | 0.6 V to VBIAS, so a 0.9 V core rail and a 5 V peripheral rail both pass |
| Bias range | 2.5 V to 5.7 V on VBIAS |
| On resistance at 25 C | 16 mOhm typical and 19 mOhm maximum with a 5 V bias, measured at 200 mA |
| On resistance over temperature | 23 mOhm maximum to 85 C and 25 mOhm maximum to 105 C |
| On resistance at 2.5 V bias | 18 mOhm typical, which is the row to use when the bias comes from a 2.5 V or 3.3 V rail |
| Quiescent current at 5 V bias | 37 microamp typical and 45 microamp maximum at 105 C |
| Quiescent current at 2.5 V bias | 14 microamp typical and 20 microamp maximum |
| Shutdown current | 0.005 microamp typical and 2.3 microamp maximum on VBIAS, with 0.5 to 3.5 microamp on VIN |
| Thermal shutdown | 160 C typical trip with 20 C of hysteresis, and the vendor notes the circuit acts under overcurrent |
| Thermal resistance | 74.8 C per watt junction to ambient in the DSG body on the vendor land pattern |
| Logic thresholds | 1.1 V minimum high and 0.5 V maximum low on the ON pin |
| Rise time | 1750 microsecond typical with 1000 pF on CT at 5 V in, 280 microsecond with a 0.6 V input |
| Output pull down | 230 Ohm typical, fitted on the TPS22975 and left out on the TPS22975N |
| Packing | 3000 pieces on a large reel, NIPDAU finish, moisture level 1 with unlimited floor life, marking 13XH |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The thermal shutdown is a protection of last resort and it should not be used as a current limit. At 160 C the die is far outside its characterised range, the on resistance has risen, and the part switches off and on at a rate set by the thermal time constant of the pad and the copper. In a product that pulls a genuine fault current the result is a ticking port rather than a clean latch, and the upstream supply sees bursts of current. A board that needs a defined fault behaviour has to add a current limited switch or a fuse, and the thermal circuit is there for the case nobody predicted.
The 5.7 V bias ceiling is higher than the 5.5 V used on the 4 A members, and that matters on a 5 V rail that runs at plus ten per cent. A 5.5 V rail at the top of its tolerance reaches 5.5 V and sits exactly on the limit of the smaller part, while the 22975 has 200 mV of headroom. It is a small thing that shows up in a qualification review as a margin question, and it is cheaper to answer by choosing the part with the higher ceiling than by tightening the rail.
The on resistance at 0.6 V input is worth a look because the part is often used to switch a low rail whose source is a buck converter with a wide output range. The switching table gives a 280 microsecond rise time at 0.6 V input with a 1000 pF CT capacitor, against 1750 microsecond at 5 V, because the internal current source that charges CT scales with the bias rather than the input. A board that expects a fixed ramp across the input range will find the fast ramp at low input and the slow one at high input, which is the opposite of what a naive reading of the CT capacitor suggests.
The 45 microamp maximum quiescent current at 105 C is the number a battery product has to use, not the 37 microamp typical. On a board with eight of these switches the difference between typical and maximum is 64 microamp, which over a year is half an amp hour. That is not a reason to avoid the part, but it is a reason to put the maximum in the standby budget rather than the typical, and to measure the sum on the first article instead of adding up the typicals.
- The bias rail tolerance, since the part allows 5.7 V and the smaller members of the family do not.
- Ramp time at both ends of the input range, because the CT pin current scales with the bias.
- The output pull down, since the N version of the same part does not have one and a drop in substitute changes the power down behaviour.
- Thermal performance with the real copper area, because 74.8 C per watt on the vendor land pattern is the best case.
- Shutdown current over temperature, which is printed separately for 85 C and 105 C.
- The moisture level and floor life, because the part is level 1 and needs no bake, which is worth knowing before a production schedule is set.
Which projects this part fits
This part fits high current rails on telecom line cards, industrial gateways, servers and storage, and any board where a 5 V rail reaches the top of its tolerance and the switch has to survive it. It also fits notebook and tablet boards that need a 6 A port with a defined thermal behaviour, and it is a direct alternative to the 4 A member when the load has grown but the land pattern is already committed.
Questions that come up before a purchase order is released
What triggers the thermal shutdown?
The junction temperature reaching about 160 C while the switch is on. The vendor states the circuit acts under overcurrent, which means a normal load at the rated current should never reach it. If a board trips it, the first thing to check is the copper under the pad, not the part.
Difference between TPS22975 and TPS22975N?
The N version has no output pull down. Everything else, including the resistance, the current rating and the timing, is the same. A substitution in either direction changes what happens to the output when the switch is off, so it should be a controlled change on the bill of materials.
Can the switch be used at 5.5 V input?
Yes, with a bias at 5.7 V or above the input. The input range goes up to the bias voltage, and the resistance rows are printed at 5 V, so a 5.5 V rail should be checked against the curves rather than the table.
How much copper does the pad need?
The vendor land pattern is the minimum. The thermal table gives 74.8 C per watt for that pattern, and a 6 A load at 25 mOhm dissipates 900 mW, which is a 67 C rise. That number is why the pad needs vias into a plane on any board that runs the part near its rating.
Is the part protected against reverse current?
Not explicitly. The body diode conducts from output to input and the pull down only acts when the switch is off. A product that can see a charged output with the rail removed needs an external blocking element.
How SUPERB handles this line
We supply the TPS22975DSGR and the N version on original 3000 piece reels, and we check the marking against the packing list because the N and non N bodies are visually identical. The power management cross reference page groups the load switches by current rating and resistance, pin to pin cross reference is where we record which members share the 2 mm WSON land pattern, and safety stock planning covers the case where a customer wants a buffer of the exact body rather than a substitute.