TPS22969DNYR
Product Specifications
TPS22969DNYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22969DNYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22969DNYR 6 A single channel load switch with 4.4 mOhm on resistance in the eight pin WSON body
The TPS22969 is the low resistance member of the single channel load switch line: 4.4 mOhm typical at any input between 0.8 V and 5.5 V with a 5 V bias, and a 6 A continuous rating. The DNY body is 2 mm by 2 mm with a thermal pad, and the part is specified over minus 40 to 105 C, which is the wider of the two windows in this family.
It exists for one reason. A processor rail that draws several amps cannot afford a switch that drops fifty millivolts, because the rail tolerance is already tight and the load transient eats most of it. At 6 A and 5 mOhm the drop is 30 mV, and the dissipation is 180 mW, which the pad can pass into copper. The part also carries a 224 Ohm output pull down and a controlled ramp on the CT pin, so the inrush into a large decoupling bank stays inside what the source can supply.
Key parameters taken from the TPS22969DNYR document
| Rated continuous current | 6 A through one switch, with the thermal pad soldered down |
| Input range | 0.8 V to 5.5 V on VIN, with VBIAS between 2.5 V and 5.5 V |
| On resistance at 5 V bias | 4.4 mOhm typical and 5.0 mOhm maximum at 25 C, 5.6 mOhm maximum over minus 40 to 85 C and 5.8 mOhm over minus 40 to 105 C |
| On resistance at 6 A | 4.6 mOhm typical and 5.8 mOhm maximum at 25 C, 6.0 mOhm maximum over the full range, which is the row that matters for a loaded rail |
| On resistance below 1 V | The same 4.4 mOhm typical at 0.8 V input, which is unusual in this class and is why the part suits core rails |
| Quiescent current | 20.4 microamp typical at 5 V bias and 26.0 microamp maximum to 85 C, 27.0 microamp to 105 C |
| Quiescent current at 2.5 V bias | Lower than the 5 V bias figure, because the charge pump works less hard |
| Shutdown current | 1.1 microamp typical and 1.5 microamp maximum on VBIAS, with 0.1 to 0.5 microamp on VIN depending on the rail |
| Rise time | 2663 microsecond typical at 5 V in with a 10 Ohm load, 0.1 microfarad output and 1000 pF on CT |
| Turn on and delay | 2397 microsecond turn on and 1009 microsecond delay under the same conditions |
| Output pull down | 224 Ohm typical and 233 Ohm maximum with the switch off |
| Thermal range | Minus 40 to 85 C in the electrical tables and minus 40 to 105 C in the addendum, both printed against this order code |
| Package | WSON DNY eight pins, 2.00 mm by 2.00 mm, with exposed pad |
| Packing | 3000 pieces on a large reel, NIPDAU finish, moisture level 2 with a one year floor life, marking 969A0 |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The resistance rows are printed for two test currents and both should be read. The 200 mA row is the small signal figure that a bench measurement usually reproduces, 4.4 mOhm typical, while the 6 A row is the one a loaded rail sees, 4.6 mOhm typical and 5.8 mOhm maximum at 25 C. The gap comes from the internal sense path and from self heating in the die, and it is the larger number that should go into a voltage drop budget. At 6 A the maximum drop over temperature is 36 mV, not the 26 mV that the small signal row suggests.
Thermal handling decides whether the 6 A rating is real. The body is 2 mm square and the pad is the only path into the board. The vendor thermal table for the DSG body of the neighbouring switch in this line gives a junction to ambient figure in the mid seventies of degrees per watt on a standard land pattern, and a 5 mOhm switch at 6 A dissipates 180 mW, which is a 13 C rise before any copper sharing. A board that puts the switch in a corner with no plane under it will run hotter than the model, and the derating paragraph in the document says exactly that: maximum ambient depends on the maximum junction temperature, the dissipation and the pad, and the user has to derate.
The 105 C window in the addendum and the 85 C window in the tables are not a contradiction, they are two statements about the same part. The electrical tables are characterised to 85 C with a 105 C column added for some rows, and the addendum prints the orderable temperature range as minus 40 to 105 C. A qualification document should quote the addendum, and a board that runs near 100 C ambient should ask the vendor for the electrical limits at that temperature before it signs. This is the same pattern we see on several parts in this family, and it is worth writing down in the component qualification file.
The ramp and the pull down are the two behaviours a firmware engineer will notice. The ramp is linear because the CT pin is a current source charging a capacitor, so the inrush into a 100 microfarad bank is a flat current for two and a half milliseconds rather than a spike, which keeps the upstream regulator out of current limit. The pull down is 224 Ohm, which discharges 100 microfarad with a 22 millisecond constant, so a rail that has to be at zero before the next measurement cycle needs either a smaller bank or an external discharge resistor.
- Load current and ambient together, because the resistance window widens with temperature and the drop budget has to hold at the hot corner.
- The bias rail, since the whole resistance table is quoted against a 5 V bias and a 2.5 V bias gives different numbers.
- The CT capacitor, because the ramp sets the inrush the source has to supply.
- The pad and the copper area under it, since the 6 A rating depends on the heat leaving through the pad.
- The floor life, because the DNY body is moisture level 2 with one year and a long stored reel needs a bake decision.
- The output pull down current while the rail is off, which is 15 mA at 3.3 V and can matter on a battery product.
Which projects this part fits
This part fits core and I/O rails on servers, network processors and FPGAs where a few milliohms decide whether the rail is inside its window, and it fits any product that switches a high current rail with a small body and cannot afford a controller plus an external FET. It is also the part to use when a board already carries the 2 mm WSON land pattern from another member of the family and the load has grown, because the pin out is the same and only the die inside changes.
Questions that come up before a purchase order is released
Why does the resistance rise at 6 A?
Because the measurement includes the internal sense element and the die heats. The document prints the 200 mA and the 6 A rows separately, and the 6 A row at 105 C is the 5.8 to 6.0 mOhm figure. A budget built on the 4.4 mOhm typical will be optimistic by about 30 per cent at the hot corner.
Is the part usable at 0.8 V input?
Yes, and the resistance is the same 4.4 mOhm typical, but the bias rail still has to be at least 2.5 V because the gate needs headroom. The combination of a 0.8 V input and a 2.5 V bias is the normal way to switch a core rail from a 3.3 V board supply.
What sets the turn on time?
The capacitor on CT together with the internal current source, and the switching table gives the 1000 pF case at 5 V, 2.5 V and 0.8 V input so the scaling can be checked. A larger capacitor gives a longer ramp and a smaller inrush.
Does the part block reverse current?
It does not have an explicit reverse blocking circuit. The body diode of the internal FET conducts from output to input, so a charged output can feed the input rail when the switch is off. A product that needs true reverse blocking should add a diode or use a part with a back to back arrangement.
What is the difference to the TPS22967?
The 22967 is 4 A with 22 mOhm and an 85 C window, the 22969 is 6 A with 4.4 mOhm and a 105 C window in the addendum. The land pattern is the same eight pin WSON, so the choice is made on current, drop and temperature, not on the board.
How SUPERB handles this line
We supply the TPS22969DNYR on original 3000 piece reels with the date code and the marking on the packing list, and we hold the moisture level 2 handling rule in our incoming inspection so a stored reel is baked before it goes to the line. The power management cross reference page lists the current ratings and resistances of the load switches we carry, component lead time solutions covers the case where the exact body is short and a substitute has to be qualified, and incoming inspection plan is the document we work to when a customer wants the reel verified before it is consumed.