TPS22965DSGT
Product Specifications
TPS22965DSGT
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22965DSGT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22965DSGT 6 A load switch with 16 mOhm on resistance and a capacitor set rise time in the 8 pin SON
The TPS22965DSGT is the highest current member of the TPS22965 line: a single channel load switch rated 6 A from 0.8 V to 5.7 V, with an on resistance of 16 mOhm at 5 V, a bias supply that can be separate from the switched rail, and a capacitor on the CT pin that sets the rise time. It sits in a 2 by 2 mm eight pin SON with a thermal pad, which is what allows it to carry six amps at all.
The part takes VBIAS and VIN separately, so a 1.2 V core rail can be switched while the gate drive runs from 5 V, and the on resistance stays at 16 mOhm from 5 V down to 1.8 V because the bias is what sets the gate voltage. The rise time is set by a capacitor from CT to ground, the quick output discharge resistor is 225 Ohm on the members that include it, and the enable threshold is low enough for 1.2 V logic. The N member drops the discharge, and the two are otherwise identical.
Key parameters taken from the TPS22965DSGT document
| Input range | 0.8 V to 5.7 V, with VBIAS between 2.5 V and 5.7 V |
| Maximum continuous current | 6 A, with the thermal pad soldered to the board |
| On resistance at 5 V | 16 mOhm typical and 21 mOhm maximum with a 5 V bias |
| On resistance at 3.6 V | 16 mOhm typical |
| On resistance at 1.8 V | 16 mOhm typical, because the bias rail holds the gate voltage up |
| On resistance with a 2.5 V bias | 18 mOhm typical and 23 mOhm maximum at 1.5 V input |
| Quiescent current | 50 microamp typical and 75 microamp maximum at a 5 V bias, 20 microamp typical and 30 microamp maximum at a 2.5 V bias |
| Rise time control | A capacitor on CT sets the ramp, with 1000 pF giving about 1600 microseconds turn on and 1985 microseconds rise into 10 Ohm and 0.1 microfarad |
| Turn off | 9 microseconds with the same load, and the fall time is 3 microseconds once the switch opens |
| Enable delay | 660 microseconds with a 1000 pF capacitor on CT |
| Quick output discharge | 225 Ohm on the TPS22965, absent on the TPS22965N, which is the only functional difference between the two |
| Enable threshold | 1.1 V minimum high level, so 1.2 V, 1.8 V, 2.5 V and 3.3 V logic all drive it |
| Body and packing | WSON DSG 8 pins, 2 by 2 mm with thermal pad, 250 pieces on a small reel for this order code, NIPDAU finish, moisture level 2 with a one year floor life, minus 40 to plus 105 C, marking ZSA0 |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
Six amps in a 2 by 2 mm body is a thermal statement rather than an electrical one. At 6 A through 21 mOhm maximum the dissipation is 756 mW, and the SON with a soldered pad has a junction to ambient figure in the order of 40 C per watt on a decent copper area, which is a 30 C rise. Without the pad soldered the same part reaches thermal shutdown at half the current. Every board that uses this part should treat the pad and its vias as a current carrying path, not as a mechanical detail.
The separate bias rail is what keeps the resistance flat. With VBIAS at 5 V the gate is driven well above a 1.8 V input, so the 16 mOhm figure holds across the whole range, and with VBIAS at 2.5 V the resistance at 1.5 V input rises to 18 mOhm typical and 23 mOhm maximum. A board that ties VBIAS to the switched rail loses that benefit and sees the resistance climb as the rail falls, which on a 1.2 V core rail is the difference between a 6 A switch and a 4 A one.
The CT capacitor sets both the inrush and the turn on delay, and the two move together. With 1000 pF the part takes 660 microseconds to start and 1985 microseconds to complete the rise, which holds the inrush into a large capacitor to a level the upstream converter can supply. With the pin open the ramp is much faster and the inrush is correspondingly larger. On a 6 A rail the risk is not the switch, it is the upstream regulator going into current limit and dropping the whole board, so the CT value is a system decision rather than a component value.
The order code on this page is the small reel row, which is unusual for a production part. The addendum prints 250 pieces on a small reel for the T suffix and the large reel row belongs to the R suffix, at moisture level 2 with a one year floor life rather than the level 1 unlimited that the wafer level parts carry. A build that needs several thousand pieces should name the R suffix, and a build that needs a floor life statement should know that this body is level 2 and has to be baked if it sits out.
- The VBIAS rail, because the flat 16 mOhm resistance depends on it being above the switched rail.
- The CT capacitor, which sets the rise time and the inrush together and is a system level decision.
- The reel size, since this code ships 250 pieces on a small reel and production quantities need the R suffix.
- The moisture level of 2 and the one year floor life, which the wafer level siblings do not have.
- The thermal pad and its vias, because 756 mW in a 2 by 2 mm body has nowhere else to go.
- The enable threshold of 1.1 V minimum, which a 1.2 V logic rail only just meets.
Which projects this part fits
This part fits core rails and peripheral rails on notebooks and ultrabooks that have to be switched at multi amp currents, tablet and docking rails where a 1.2 V rail is switched from a 5 V housekeeping supply, solid state storage with a rail that draws several amps, and any board where the rise time has to be tuned to an upstream regulator's current limit. The 2 by 2 mm SON with a thermal pad is the reason it can be used at 6 A where a wafer level part cannot.
Questions that come up before a purchase order is released
Does the part need a separate bias supply?
It has a VBIAS pin that can be tied to the switched rail if that rail is 2.5 V or higher, but the on resistance figures assume a bias above the input. For a 1.2 V or 1.8 V rail the bias has to come from a higher supply, otherwise the gate drive is weak and the resistance climbs.
What CT value gives the slowest rise?
Larger capacitance gives a longer ramp, and the vendor prints 1000 pF as the reference point at about 2 ms of rise. The limit is the leakage the pin can tolerate; a very large capacitor leaks and the ramp becomes unpredictable, so the useful range is the one the switching table covers.
Why does this code ship on a 250 piece reel?
Because the T suffix is the small reel row in the addendum. The large reel belongs to the R suffix, with the same body and the same electrical limits. A production order should use the R suffix, and a prototype order can use the T.
Is the quick output discharge always fitted?
On the TPS22965 it is, at 225 Ohm, and on the TPS22965N it is not. The comparison table in the document is the place to confirm which one a given order code carries, because the two share a body and a pin out.
What is the moisture sensitivity of the SON body?
Level 2 with a one year floor life, against level 1 unlimited on the wafer level parts in the same family. A board that stores reels for a long time has to plan a bake before the run, and the packing list should carry the level so the assembly house can act on it.
How SUPERB handles this line
We supply the TPS22965DSGT on original 250 piece reels for prototypes and on the large reel row for production, with the date code and the marking recorded, and we can supply the N member when a board does not need the discharge. The power management cross reference page lists the high current switches by resistance, current and package, BOM consolidation covers the case where a product family uses both members of this line, and kitting service is how we deliver these parts against a notebook or storage build.