TPS22916CYFPR
Product Specifications
TPS22916CYFPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22916CYFPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22916CYFPR 2 A load switch with slow turn on and always on reverse current blocking in the 4 bump WCSP
The TPS22916CYFPR is the C timing member of the TPS22916 family: a single channel load switch rated 2 A from 1 V to 5.5 V, in a four bump wafer level package that is under a millimetre square, with the slow turn on option chosen to keep inrush low. The family covers active high and active low enables, fast and slow timing, and with or without quick output discharge, and the C letter in the order code is the slow one.
The switch element is a P channel MOSFET with a typical on resistance of 60 mOhm at 5 V and 200 mOhm at 1 V, so the part keeps working at the bottom of a single cell range where most load switches have given up. The gate control keeps the resistance from climbing steeply as the input falls, which is the reason the family is used on rails that are themselves decaying. Reverse current blocking is always on, including while the switch is enabled, which is the behaviour a battery backed rail needs.
Key parameters taken from the TPS22916CYFPR document
| Input range | 1 V to 5.5 V, with the on resistance quoted at 5 V, 3.6 V, 1.8 V, 1.2 V and 1 V |
| Maximum continuous current | 2 A |
| On resistance at 5 V | 60 mOhm typical and 80 mOhm maximum at 25 C, 100 mOhm over minus 40 to plus 85 C and 120 mOhm to 105 C |
| On resistance at 1.8 V | 100 mOhm typical and 125 mOhm maximum at 25 C, 150 mOhm over the standard range |
| On resistance at 1 V | 200 mOhm typical and 275 mOhm maximum at 25 C, 325 mOhm over the standard range |
| Quiescent current | 0.5 microamp typical and 1 microamp maximum with the switch on |
| Shutdown current | 10 nA typical and 100 nA maximum on the B, C and CN members, 100 nA typical and 300 nA maximum on the L members |
| Turn on time, this member | 1400 microseconds at 5 V, 3000 microseconds at 1.8 V and 6500 microseconds at 1 V, which is the slow timing that limits inrush |
| Turn on time, the fast member | 115 microseconds at 5 V, 250 microseconds at 1.8 V and 510 microseconds at 1 V, for comparison |
| Reverse current blocking | Always active, trips at about minus 500 mA, acts within 10 microseconds and releases at 25 mV of forward bias |
| Reverse leakage | 300 nA maximum while blocking |
| Quick output discharge | 150 Ohm on the members that include it, absent on the CN and CNL parts |
| Enable | 10 nA maximum leakage when driven high, with a 750 kOhm smart pull down that holds the pin low until the system drives it |
| Body and packing | DSBGA YFP four bumps, 0.78 by 0.78 mm, 0.4 mm pitch, 0.5 mm height, 3000 pieces on a large reel for the R suffix against 250 for the T suffix, moisture level 1 |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The slow turn on is the reason to pick the C member, and it changes what the board needs around it. At 5 V the output rises over about 1.4 ms and at 1 V over about 6.5 ms, which holds the inrush into a capacitive load to a level a small battery or a weak host port can supply. The same rail with the B member rises in 115 microseconds and draws a spike that is ten times larger. A product that has a 100 microfarad bank on the switched rail and a host that limits at 500 mA needs the C member, and a product that has 1 microfarad and needs the rail up before the processor releases reset wants the B member. The order code decides this, and the two are not interchangeable in a socket.
The 1 V capability is not a marketing number, it is the reason the part exists in single cell products. At 1 V input the on resistance is 200 mOhm typical and 325 mOhm maximum over temperature, so a 1 A load dissipates 325 mW and the four bump body has to get rid of it. In practice the part carries hundreds of milliamps at the bottom of the range and the full 2 A near 5 V. A board that expects 2 A at 1 V is outside what the thermal path can do, and the resistance curve is the place to see it rather than the headline current.
Reverse current blocking being always on separates this part from the older switches that only block while disabled. The comparator trips when the output is driven about 500 mA above the input, reacts within 10 microseconds and releases at 25 mV, so a rail that is back fed by a charged load or by another supply cannot push current into the input. The leakage while blocking is 300 nA maximum, which is small but not zero, and a product that measures its off state current in nanoamps has to count it. The behaviour is the same whether the switch is on or off, which is what makes it usable on a rail that is shared between a battery and a charger.
The smart pull down on the enable pin is a detail that saves boards. Until the system drives the pin high, an internal 750 kOhm resistor holds it low, so the switch stays off while the processor is in reset and its pins are high impedance. Once the pin is driven high the pull down disconnects and the only load is 10 nA of leakage. A board that adds an external pull down of its own is not wrong, but it is drawing current the part already handles, and on a sleep current budget of a few microamps that matters.
- The timing letter in the order code, because the C and B members differ by a factor of ten in turn on time and inrush.
- The on resistance at the actual minimum input, since 1 V operation costs 325 mOhm maximum over temperature.
- The dissipation in the four bump body at the load current and the ambient the product sees, because there is no thermal pad to spread it.
- Reverse blocking leakage in the off state budget, 300 nA maximum, which is small but appears in every nanoamp calculation.
- The quick output discharge option, since it decides whether the rail collapses when the switch opens.
- The enable pull down, which is internal at 750 kOhm and does not need an external part.
Which projects this part fits
This part fits single cell battery products where a peripheral rail has to be switched without collapsing the cell, wearables and hearables with a 1.8 V sensor rail and a tight sleep budget, internet of things modules that need reverse blocking on a rail shared with a charger, and portable instruments where the processor has to be able to disconnect a load before it sleeps. The four bump package is small enough to sit beside the connector, and the 1 V floor means the rail stays in specification as the cell discharges.
Questions that come up before a purchase order is released
How do I tell the C member from the B member on a reel?
By the order code and the reel label. The bodies are the same four bump package and the marking is the same family marking, so the only reliable separation is the part number on the reel. A build that mixes them shows up as inconsistent inrush, which is hard to diagnose after the fact, so the incoming inspection should verify the code.
Does reverse blocking work when the switch is on?
Yes. The comparator is always active and trips when the output is driven above the input by roughly the activation current, which the vendor prints as about minus 500 mA, with a 10 microsecond response. That is what allows the part to sit on a rail that another supply can take over.
Is there a thermal pad or a ground plane requirement?
There is no pad. The four bumps are the whole thermal path, and the vendor's thermal information assumes the board copper around the bumps. A 2 A load at 5 V through 80 mOhm is 320 mW, which needs the copper area the land pattern shows, and at high ambient the load has to come down.
What is the difference between the CN and the C member?
The CN and CNL parts drop the quick output discharge, so the output is not pulled down when the switch opens. Everything else, including the slow timing and the on resistance, is the same. A rail that has to bleed down for a reset sequence needs the C or the B member, not the CN.
Can the enable be driven from a 1.2 V logic pin?
The enable thresholds are not specified against a rail in the front page summary, so a 1.2 V logic high has to be checked against the electrical table for the input voltage in use. If the margin is thin, drive the pin from the higher rail through a level translator rather than relying on the threshold.
How SUPERB handles this line
We supply the TPS22916CYFPR on original reels with the timing letter and the date code recorded on the packing list, and we can supply the B member or the active low L member of the same family when a board changes its sequencing. The power management cross reference page lists the load switches by current, timing and package, BOM consolidation covers the case where one product family uses several timing members, and kitting service is how we deliver these parts against a build schedule.