Contact Us

TPS22914BYFPR

Brand: Texas Instruments
Texas Instruments TPS22914BYFPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22914BYFPR — Power Management & Signal Chain | Superb Automation

TPS22914BYFPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22914BYFPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22914BYFPR: 2 A load switch in a 0.5 mm wafer level package

TPS22914BYFPR is a single channel 2 A load switch with a fast gate ramp in a WCSP body of 4 pins. It is a four bump wafer level device in a 0.5 mm height body, aimed at boards where the switch has to fit under a connector or beside a module.

Order code and package

Order codeTPS22914BYFPR, YFP package, four bump WCSP
Body0.5 mm height, 0.4 mm pitch, laser marked and bump side down
Input range1.05 V to 5.5 V, which covers a single cell rail up to a 5 V system rail
Rated current2 A maximum continuous
Output dischargeNone on this member; the 143 ohm pulldown belongs to the TPS22915B and C

Electrical parameters that decide the application

On resistance38 mOhm typical at 3.3 V, 43 mOhm at 2.5 V, 52 mOhm at 1.8 V, 63 mOhm at 1.2 V, all at 200 mA
Turn on time104 us typical at 5 V into 0.1 uF with a 10 ohm load, 1300 us on the C variant
Rise time89 us typical at 5 V, 1277 us on the C variant, which is the inrush control difference between the two
Turn off time2 us typical, with the output following the load rather than being pulled down
Enable thresholdAbout 0.9 V rising with 92 mV to 102 mV of hysteresis across the input range
Quiescent currentVery low in the microamp range with the switch on, and leakage only with it off
Body sizeFour bumps on a 0.4 mm pitch in a body under a millimetre square

Family variants and how they differ

TPS22914CSame die with a slow ramp for inrush control into a large capacitance
TPS22915BAdds the 143 ohm quick output discharge and keeps the fast ramp
TPS22915CAdds the discharge and uses the slow ramp
TPS229204 A in a DSBGA body for a higher current rail
TPS229926 A with a separate bias pin when the input rail is below the gate drive requirement

Points to check before this part goes on a BOM

The 38 mOhm typical at 3.3 V is the headline and the whole point of the part. At 2 A the drop is 76 mV and the dissipation is 152 mW, which in a body under a millimetre square is a real thermal question rather than a footnote. The datasheet derates the on resistance across the input range for exactly this reason, and a 1.2 V rail at 2 A drops 126 mV and dissipates 252 mW, which is more than the package can pass continuously without the board copper doing the work.

The fast ramp on this member is a deliberate trade against inrush. 89 us of rise time keeps the switch out of the way of a rail that is sequenced by a controller, and it lets a port power up quickly enough for enumeration. The same speed into a large capacitance draws a current limited only by the capacitance and the on resistance, so a 100 uF load at 3.3 V draws several amps for the ramp and the upstream supply has to source it. The C variant with its 1277 us ramp exists for that case.

There is no output discharge on this order code. When the switch turns off the output follows the load, which on a rail with a large capacitance can stay up for seconds. A port that must present a discharged state at turn off needs the TPS22915B or C, which add the 143 ohm pulldown, and the order code has to carry the 15 rather than the 14.

The four bump body has no thermal pad and no leadframe. Heat leaves through the bumps into the board, so the copper under and around the device is the thermal path, and a footprint copied from a competitor's land pattern without the same copper area will run hotter. At 2 A the difference between a 76 mV and a 100 mV drop is the difference between a comfortable and a marginal junction.

The enable threshold of about 0.9 V rising, with 92 mV to 102 mV of hysteresis, is low enough to be driven directly by a 1.2 V or 1.8 V GPIO. That is uncommon in this class and it is the reason the part appears on processor rails where the only available control signal is a low voltage pin. The hysteresis is what keeps a slow rising enable from oscillating at the threshold.

The input range of 1.05 V to 5.5 V means the part can sit on a single cell battery rail and on a 5 V system rail with the same order code. What changes is the on resistance, which roughly doubles from 5 V to 1.2 V, and the current capability, which is set by the thermal path rather than by the silicon. A 2 A rating on a 1.2 V rail is a 252 mW dissipation, and the package rating has to be read against the board it lands on.

Quiescent current is in the microamp range, which matters on a battery rail that is switched rather than regulated. The switch itself should not be the reason a product fails a sleep current target, and the off state leakage is the number to check: a load switch that leaks a few microamps per rail across ten rails is a measurable fraction of a modern sleep budget.

The 0.5 mm height is what makes the part usable under a connector or on the back of a module board. That height also limits the solder joint volume, so the assembly profile and the stencil aperture matter more than they do for a SOT-23. A reflow profile copied from a larger board can leave the bumps with insufficient collapse and a joint that passes test and fails in the field.

A wafer level part has no compliant leads, so the solder joints carry the board flex. That is what the coated body option addresses, and it is also why the land pattern has to follow the vendor drawing rather than a generic four pad footprint. The bumps are 0.4 mm apart, which is inside the capability of a standard stencil but not of a coarse one, and the paste volume has to be right or the bump does not collapse properly. A board that is depanelised by hand after reflow will crack more of these parts than one that is routed, and the failure looks like an open switch with no visible damage.

Where this order code fits

It is the switch for a processor or sensor rail that has to be sequenced under software control on a board with no height budget, typically a module, a wearable or a camera board where the rail is a 1.8 V or 3.3 V domain and the current is under 2 A. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does it discharge the output at turn off? No, this order code has no quick output discharge; the TPS22915B or C adds a 143 ohm pulldown.

Can a 1.2 V GPIO drive the enable pin? Yes, the threshold is about 0.9 V rising, so 1.2 V logic drives it directly with margin.

What is the drop at 2 A on a 3.3 V rail? 76 mV at the typical 38 mOhm, which is 152 mW in the package.

Why are there B and C versions? The B ramps in about 89 us and the C about 1277 us; the C is for loads whose capacitance would otherwise draw a large inrush.

Does it need input and output capacitors? Yes, a ceramic input capacitor close to the VIN bump and an output capacitor at the load, both sized for the load step rather than for the DC current.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.