Contact Us

TPS2141IPWP

Brand: Texas Instruments
Texas Instruments TPS2141IPWP is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2141IPWP — Power Management & Signal Chain | Superb Automation

TPS2141IPWP

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2141IPWP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2141IPWP adjustable LDO with a 5 V switch and dual current limit for USB high power peripheral power management

The TPS2141IPWP is a combined power device for a USB high power peripheral: an adjustable low dropout regulator rated 250 mA, a 5 V power switch rated 500 mA, two power good outputs and a dual current limit on the switch. It is the generation of part that put the whole peripheral supply into one 14 pin HTSSOP body, at a time when a USB peripheral had to draw its own rail from the bus and still keep the inrush inside what the host would tolerate.

The interesting part is the dual current limit. While the switch output is below 93 per cent of its input, the switch holds the current to 100 mA maximum, so a large output capacitor charges slowly and the host port does not see a surge. Once the output is above that threshold the limit opens to 1800 mA maximum, which is enough for the peripheral to run, and if the output then collapses below 80 per cent of the input the part returns to the low limit instead of sitting in a hard short. That two level behaviour is what allows a product to carry a large capacitor on the bus side without tripping a host that only guarantees 500 mA.

Key parameters taken from the TPS2141IPWP document

Switch continuous current500 mA, with an on resistance of 40 mOhm typical and 65 mOhm maximum
Switch current limit, low state100 mA maximum while the output is below 93 per cent of the input, which is the inrush window
Switch current limit, high state1800 mA maximum once the output is above 93 per cent of the input
Return to low limitWhen the output falls below 80 per cent of the input, the part reverts to the low limit rather than holding the high one
Switch enableActive low on the TPS2141 with an internal pull up, active high on the TPS2151 with an internal pull down
Switch power goodCMOS output, active high, no external pull up needed, and it goes low below 88 per cent of the 5 V rail
LDO output current250 mA continuous with a 325 mA typical current limit
LDO input range2.7 V to 5.5 V, with the output adjustable from 0.9 V to 3.3 V through a divider on the ADJ pin
LDO dropout0.5 V maximum at the full 250 mA, quoted in the pin description rather than in a marketing line
LDO power goodOpen drain, active high, needs a pull up, and it has a 150 microsecond falling deglitch filter
LDO power good thresholdThe output has to be above 94 per cent of the divider threshold, so the divider sets both the rail and the monitor point
Supply current85 microamp typical with both blocks active, 5 microamp typical in standby
Body and packingHTSSOP 14 pins with PowerPAD, tape and reel with an R suffix on the order code, minus 40 to plus 85 C ambient

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The two current limit states are the reason this part exists, and they are also the reason a marginal board fails qualification. A host port that only guarantees 500 mA will still deliver a surge while a downstream capacitor charges, and a plain switch with a 1.8 A limit would take that surge for as long as the capacitor needs. The 100 mA low state stretches the charge over a longer time, and the vendor prints the relationship between the load capacitance and the charge time so the inrush can be planned rather than discovered. A product with 100 microfarad on the switched rail charges inside the published window; a product with 1000 microfarad does not, and no amount of firmware will change that.

The LDO dropout figure is the constraint on the core rail. The part is a true low dropout regulator with 0.5 V maximum at 250 mA, which means a 3.3 V input cannot deliver a 3.0 V output at full load with any margin, and a 3.3 V input to a 1.8 V core rail has 1.5 V of headroom and is comfortable. In a USB peripheral the input is the bus voltage, which can sit at 4.4 V under load, so a 3.3 V rail is safe and a 3.0 V rail is not. The adjustable range starts at 0.9 V, which is the DSP core territory this part was written for, and the divider on ADJ sets both the output and the monitor point, so a divider change moves the power good threshold with the rail.

The power good behaviour differs between the two outputs and that catches people. The switch power good is a CMOS push pull output that needs no pull up and goes low below 88 per cent of the rail, while the LDO power good is open drain, needs a pull up, and has a 150 microsecond falling deglitch. A board that ties the two together will hold the LDO line low through the switch line and lose the distinction between a bus problem and a core problem. Keeping them separate, and giving the open drain pin its own pull up to the rail it monitors, costs one resistor and keeps the diagnostics usable.

The pulldown pins are easy to leave unconnected and they matter at power down. SW_PLDN and LDO_PLDN are open drain outputs that provide a discharge path when the corresponding block is disabled, and they are meant to be connected to the output they serve. A board that leaves them open keeps a charge on the output capacitor for as long as the load draws nothing, which shows up as a peripheral that does not re enumerate after a soft reset because the rail never fell below the reset threshold. Connecting the pin to the rail it discharges is the fix, and it costs no components.

  • The actual capacitance on the switched rail, because the 100 mA low state only holds inrush inside the host budget for a bounded capacitor.
  • The LDO headroom at the minimum bus voltage under load, which is the case where a 3.0 V rail stops regulating.
  • The divider on ADJ, since it sets the output and the 94 per cent monitor point at the same time.
  • Both power good lines kept separate, with the open drain one pulled up to the rail it watches.
  • The two pulldown pins connected to their rails, so a soft reset actually discharges the outputs.
  • The thermal pad, because two blocks in one body at 85 C ambient need the copper the vendor land pattern shows.

Which projects this part fits

This part fits USB high power peripherals that have to take their supply from the bus, small instruments with a DSP core rail and a 3.3 V input output rail in one package, ADSL modems and camera products of the generation this document was written for, and any board where a switch and a regulator have to come up in a defined order with a handshake between them. The LDO power good driving the switch enable is the sequencing pattern the vendor shows, and it is cheaper than a supervisor plus two enables.

Questions that come up before a purchase order is released

Can the switch and the LDO be used independently?

Yes, they are separate blocks with separate enables, separate inputs and separate power good outputs. The only shared node is ground and the internal supply selector, which takes the higher of the two inputs. A board can use one and leave the other disabled with its enable tied to the state that keeps it off.

What sets the switch current limit, and can it be changed?

Nothing external. The two levels are fixed inside the part at 100 mA maximum in the low state and 1800 mA maximum in the high state, and the transition is set by the 93 per cent and 80 per cent thresholds on the output. If a product needs a different limit, it needs a different part.

Is 500 mA enough for a USB 2.0 high power port?

It is the ceiling the part is rated for, and the USB specification allows a high power function to draw that much after enumeration. The switch is not a charger and does not negotiate anything, so the host has to have granted the current before the load is turned on. The part protects the port, it does not manage the protocol.

Why does the LDO power good need an external pull up?

Because it is an open drain output, which lets it signal to a rail that is different from the LDO output. The pin pulls low when the output is below 94 per cent of the divider threshold, after a 150 microsecond falling deglitch, and the pull up sets the logic level the receiving device sees.

What happens if the bus voltage drops below the LDO input range?

The regulator stops regulating and the LDO power good goes low, while the switch continues to pass whatever the bus delivers up to its current limit. A peripheral that needs a clean rail during a bus transient has to hold its own bulk capacitance, because neither block in this part stores energy.

How SUPERB handles this line

We supply the TPS2141IPWP on original tape and reel with the date code recorded, and we can supply the TPS2151IPWP when a board needs the active high switch enable instead of the active low one. The power management cross reference page lists the combined regulator and switch parts by block count and rating, kitting service covers builds where this part ships with the passives and the connectors for the same assembly, and BOM consolidation is how we handle a family of boards that use two members of this line.