TPS2117DRLR
Product Specifications
TPS2117DRLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2117DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2117DRLR: 4 A power multiplexer with 20 milliohm switches and 50 nA standby
TPS2117DRLR is a two input power multiplexer in the eight pin DRL body that selects between a 1.6 V to 5.5 V primary and a backup rail, holds 20 milliohm of on resistance at 4 A, draws 1.32 uA of quiescent current and 50 nA from the standby input in a SOT body of 8 pins. The TPS2117 switches a load between two supplies in the 1.6 V to 5.5 V range with 20 milliohm of on resistance and a 4 A continuous rating. Three modes are available: priority, where the higher input wins, manual, where a logic input selects, and diode, where both inputs are effectively ORed. The output slew rate is controlled at about 1.3 ms at 3.3 V, reverse current is blocked when the output exceeds an input, and the body is an eight pin SOT.
Order code and package
| Order code | TPS2117DRLR |
| Function | two input power multiplexer |
| Input voltage range | 1.6 V to 5.5 V |
| Maximum continuous current | 4 A |
| On resistance | 20 milliohm typical |
| Quiescent current | 1.32 uA typical |
| Standby current on the second input | 50 nA typical |
| Switchover modes | priority, manual and diode |
| Output slew rate | 1.3 ms typical at 3.3 V |
| Package | eight pin SOT, DRL body |
Electrical parameters that decide the application
| Reverse current blocking | when the output exceeds either input |
| Thermal shutdown | included |
| Junction to board characterization parameter | 17.9 C per W |
| Priority mode | the higher input supplies the load |
| Manual mode | a logic input selects the source |
| Diode mode | both inputs contribute, no reverse flow |
| Continuous current at 4 A | 80 mV drop and 0.32 W in the switch |
| Control threshold | set by the two input voltages in priority mode |
Points to check before this part goes on a BOM
Twenty milliohms at 4 A is 80 mV of drop and 0.32 W of loss, which is the price of not using two diodes. A Schottky pair with 0.4 V of forward drop at the same current would dissipate 3.2 W and lose a tenth of a 3.3 V rail, so the multiplexer is worth its complexity wherever the load is more than a few hundred milliamps. The 4 A rating is the switch rating; the thermal path is the eight pin SOT and the 17.9 C per W junction to board parameter.
Fifty nanoamps of standby current on the unused input is the number that makes this part suitable for a backup cell. A 200 mAh coin cell feeding 50 nA lasts for centuries in theory and is limited by its own self discharge in practice, so the multiplexer is effectively invisible. The 1.32 uA quiescent current belongs to the active path, and even that is 11.6 mAh a year, which is small against most backup loads.
The three modes cover three different product behaviours. Priority mode is for a main supply with a backup, where the load follows whichever input is higher and the transition is automatic. Manual mode is for a product that wants the controller to decide, for example to stay on battery during a brownout rather than switch to a noisy rail. Diode mode ORs the two inputs so both can contribute, which is useful when the two sources are similar and the load can be shared, and it is the only mode where reverse current is handled by the switch rather than by the priority logic.
Reverse current blocking matters when the output is held up by capacitance after the input is removed. Without it, the output discharges back into the source that just went away, which can damage a battery or a regulator that is not expecting current to flow backwards through it. The condition is stated as the output exceeding either input, so the block is a property of the switch rather than of the mode.
The 1.3 ms slew rate at 3.3 V is the reason a switchover does not produce a dip. When the active input fails and the other one takes over, the output capacitance is charged through the switch at a controlled rate, so the load sees a ramp rather than a step. A faster switch would be better for hold up time and worse for inrush, and 1.3 ms is the compromise the part makes for a load in the milliamp to amp range.
Priority mode thresholds are set by the two input voltages rather than by an external reference, which means the switchover point has a tolerance that has to be checked against the rails it is comparing. On a 3.3 V main and a 3.0 V backup the margin is 300 mV, and a main rail that sags under load can cross the threshold and hand the load to the backup earlier than intended. The practical fix is to run the backup lower than the worst case main rail, not closer to its nominal.
Where this order code fits
This order code belongs on products with a main rail and a backup cell: meters, smoke and gas detectors, portable instruments, memory backup and any board that has to keep a real time clock or a small load alive when the main supply is removed. It is also used where a USB input and a battery have to share a load without either one feeding the other. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can this replace two Schottky diodes? For a load above a few hundred milliamps, yes, and the saving is significant: 20 milliohms against 0.4 V of forward drop at 3 A is 60 mV against 400 mV, and 0.18 W against 1.2 W. Below a hundred milliamps the diode pair is simpler and cheaper and the loss is irrelevant. The multiplexer also blocks reverse current, which a diode does by construction and a discrete FET arrangement does not.
What happens during a switchover? The output is charged from the newly selected input through the switch at a controlled slew rate, about 1.3 ms at 3.3 V, so the load sees a ramp instead of a step. The output capacitance holds the rail up during the transition, and the size of that capacitance decides whether the load sees a dip. A load that draws amps needs enough capacitance to cover the ramp.
How is the switchover point set in priority mode? By the two input voltages. The switch compares them and hands the load to the higher one, so the choice of rails sets the threshold. A 3.3 V main and a 3.0 V backup give 300 mV of separation at nominal, and a main rail that sags under load eats into it. The backup should sit clearly below the worst case main voltage rather than just below its nominal.
Is 50 nA of standby current realistic in a product? It is the current drawn from the input that is not supplying the load, and it is small enough to be ignored against a lithium cell's self discharge. What matters more is the leakage of the load itself and of the decoupling around it. A board that quotes 50 nA in a datasheet and then sits behind a 10 uA supervisor has gained nothing from the multiplexer.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.