Contact Us

TPS2113ADRBR

Brand: Texas Instruments
Texas Instruments TPS2113ADRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2113ADRBR — Power Management & Signal Chain | Superb Automation

TPS2113ADRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2113ADRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2113ADRBR: a two input power multiplexer that hands a 2 A load from a battery to a wall adapter without glitching the rail

TPS2113ADRBR is an auto switching power multiplexer with two input paths and one output, low resistance switches and a current limit set by a single resistor in a SON (DRB) body of 8 pins. It works from 2.8 V to 5.5 V on either input, delivers up to 2 A, blocks reverse and cross conduction, draws 55 microamp while operating and 0.5 microamp in standby, and slews the output when it moves between inputs so the inrush into the load capacitor stays controlled.

Order code and package

TPS2113ADRBRSON (DRB) body, 8 pins, 3.00 mm by 3.00 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 1 at 260 C unlimited floor life, marking PTOI, minus 40 C to 85 C
TPS2113ADRBTthe same body on a 250 piece small reel, the string a pilot build orders
TPS2113ADRBRG4the same string with the G4 suffix, same body and same packing, the row to order when the finish has to be stated explicitly
Suffixed rowsthe addendum repeats the DRB strings with a .B suffix at moisture level 2, so the moisture level has to be read on the row rather than taken from the part number
TPS2113APWthe TSSOP (PW) body with 8 pins, 150 pieces in a tube, the row for a line that still runs through hole or hand placement
TPS2112APWRthe sibling on the same pinout with 120 milliohm switches and a different current limit equation, 2000 pieces on a large reel

Electrical parameters that decide the application

Input voltage2.8 V to 5.5 V on both inputs, which covers a single lithium cell and a regulated 5 V adapter on the same board
Output currentup to 2 A depending on the body and the copper, set by the switch resistance and the thermal path rather than by a fixed limiter
Switch resistance84 milliohm typical on the TPS2113A and 120 milliohm typical on the TPS2112A, which is the number that decides the drop at 2 A
Standby current0.5 microamp typical with the output off, which is what makes the part usable on a battery that sits in a drawer
Operating current55 microamp typical with the output on, so the mux itself does not load the rail it is switching
Current limitset by a resistor from ILIM to ground, with 500 divided by RILIM on the TPS2113A and 250 divided by RILIM on the TPS2112A
Limit accuracythe 400 ohm and 700 ohm rows in the electrical table bracket the limit between 0.30 A and 1.56 A depending on the device and the resistor
Settling1 ms for the output current to settle inside 10 per cent of its steady state value after a short circuit is removed
Senses threshold0.78 V rising and 0.755 V falling with about 45 mV of hysteresis, which is where the switchover decision is made
Deglitch150 microsecond typical on the sense comparator, which keeps a short dip on one input from moving the load to the other
Protectionthermal shutdown, cross conduction blocking and reverse conduction blocking on both paths
Slew controlthe output moves slowly when the mux comes out of a high impedance state and quickly when it moves between the two inputs, so the inrush and the droop are handled by the same circuit

Family variants and how they differ

TPS2113A84 milliohm switches and a 500 over RILIM limit, the lower resistance member of the pair
TPS2112A120 milliohm switches and a 250 over RILIM limit, the member that reaches a lower current limit with the same resistor
DRB and PWthe same die in a 3.00 mm SON and an 8 pin TSSOP, so the choice is a board and a packing decision rather than an electrical one
Reel size3000 pieces on the large reel in the SON body, 250 on the small reel, 2000 on the large reel and 150 in a tube in the TSSOP body
Moisture levelthe base DRB row is level 1, while the .B rows are level 2 at 260 C for one year, which changes the floor life after the bag is opened

Points to check before this part goes on a BOM

The current limit resistor is not optional. Setting the ILIM resistor to zero disables the current limit, and the document states that this is not recommended, because the switch then has no protection against a short on the output.

Both paths block in both directions. Reverse conduction and cross conduction are stopped inside the device, so a charged output cannot feed back into a dead input and the two supplies cannot fight each other.

The comparator has 150 microseconds of deglitch. A dip shorter than that on the active input will not hand the load to the other supply, which is what keeps a load step from looking like a supply failure.

The slew rate changes with the transition. Coming out of a high impedance state the output ramps slowly to limit inrush, and moving between the two inputs it moves fast to limit droop, and both behaviours come from the same internal circuit.

The two bodies differ only in packing and thermal path. The SON body is 3.00 mm square and the TSSOP body is larger, so at 2 A the SON body needs more copper under it to stay inside the temperature range.

What the switchover looks like on a real load

The two inputs sit at different voltages in most systems, a 4.2 V battery and a 5 V adapter for example. The mux compares the two through a resistor divider on the sense pin and moves the load to the higher one, with the 45 mV of hysteresis deciding how far the adapter has to fall before the battery takes over again.

The output capacitor is what carries the load during the transition. A few microfarads hold the rail through the switch, and the slew control keeps the inrush inside the current limit when the rail comes back up after a long dropout.

The resistor on the ILIM pin is also the place where a substitute goes wrong. Two devices in the same body use different equations, 500 over the resistor against 250 over the resistor, so a board built for one and fitted with the other reaches half or twice the intended limit. That is the first check when a board that passed a short circuit test on the bench fails the same test after a purchasing change.

Where this order code fits

It fits a handheld instrument, a portable terminal or a camera, where a battery and a wall adapter have to feed one rail and neither may back feed the other. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Does it switch automatically? Yes. In the auto switching mode the device compares the two inputs and hands the load to the higher one, with hysteresis so the load does not bounce between them at similar voltages.

What sets the current limit? A resistor from ILIM to ground. On the TPS2113A the limit is 500 divided by the resistor value, and on the TPS2112A it is 250 divided by the resistor value.

Can the two supplies be different voltages? Yes, as long as both stay inside 2.8 V to 5.5 V. The mux moves the load to the higher input, so a 4.2 V battery and a 5 V adapter work together.

Is the TSSOP version the same part? It is the same die in a different body. The electrical behaviour is the same, and the choice comes down to the board, the packing and the thermal path at 2 A.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.