Contact Us

TPS2069DDBVR

Brand: Texas Instruments
Texas Instruments TPS2069DDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2069DDBVR — Power Management & Signal Chain | Superb Automation

TPS2069DDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2069DDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2069DDBVR: 1.5 A current limited switch with output discharge

TPS2069DDBVR is a single channel 1.5 A current limited power switch with output discharge in a SOT-23 body of 5 pins. It carries a 1.5 A rating, a 2.15 A typical limit and a 470 ohm pulldown on the output when the switch is off.

Order code and package

Order codeTPS2069DDBVR, DBV package, SOT-23 five lead
DatasheetSLVSDQ5, initial release December 2016
Rated current1.5 A continuous
Output dischargeYes, 470 ohm typical pulldown while disabled
EnableActive high, 1 V to 2 V threshold with 70 mV to 200 mV of hysteresis

Electrical parameters that decide the application

Current limit1.7 A minimum, 2.15 A typical, 2.5 A maximum at 5 V, and 1.6 A to 2.7 A over the full temperature range
Short circuit response2 us typical, measured from the application of a 50 mOhm short to the current falling below 120 percent of final value
Under voltage lockout3.5 V rising, 3.75 V typical, 4 V maximum with 140 mV of hysteresis
Output pulldown400 ohm minimum, 470 ohm typical, 600 ohm maximum at 5 V
Fault deglitch6 us to 12 us on the flag output
Thermal shutdown135 C rising junction in current limit, 20 C of hysteresis
Quiescent current0.1 mA typical and 1 mA maximum disabled, 85 uA typical enabled

Family variants and how they differ

TPS2069C1 A member of the C family, limit centred at 1.55 A
TPS2069C-21 A with the output discharge option
TPS2051C0.5 A member in the same body
TPS2561Two adjustable channels where 1.5 A fixed is wrong for one of the ports
TPS2553Adjustable limit with a latched option for a fault that must stay off

Points to check before this part goes on a BOM

The 1.5 A rating is the highest current in a five lead SOT-23 that this family offers, and the thermal budget is what limits it. The part is boarded so the limit sits above 1.5 A, but 1.5 A through the body at the maximum resistance dissipates more than the 1 A member and the 224.9 C/W figure becomes the deciding number. A 1.5 A load at 70 C ambient is at the edge of what the package can pass without extra copper.

The under voltage lockout at 3.5 V to 4 V is a deliberate choice that differs from the 0.5 A and 1 A members. It means the switch does not turn on until the rail is well above 4 V, which keeps a 5 V port from passing a brownout through to a load that would misbehave at 4.2 V. It also means a 3.3 V rail cannot use this part at all, because the lockout never releases.

The output pulldown is the reason to specify the D part. At 470 ohm typical it removes the charge from a load capacitance in a few time constants rather than leaving the port floating at whatever voltage the load held. On a USB port that has to re enumerate a device, or on a card slot that must not present a residual voltage during a hot swap, that behaviour is the difference between a working product and a port that needs a manual power cycle.

The current limit window of 1.7 A to 2.5 A is wide in absolute terms and narrow in relative terms, which is the right way round for a 1.5 A load. The risk sits at the top: a supply that folds back below 2.5 A will collapse before the switch limits, so the upstream regulator needs a current capability above 2.5 A or a controlled foldback that holds the rail. The 1.6 A to 2.7 A over temperature widens the same window at the extremes.

The thermal shutdown at 135 C with 20 C of hysteresis is what makes a sustained short survivable. The switch sits in constant current at 2.15 A and dissipates 5 V times that current, which is 10.8 W, so the junction climbs within milliseconds. The 20 C of hysteresis prevents a rapid retry cycle at the trip point, but the part still hiccups rather than latching off, and a product that must stay off after a port short needs the latched variant of a different family.

The flag has a 6 us to 12 us deglitch. An overload shorter than that does not assert the pin but still pulls the output into constant current, so the host can see a rail dip with no fault indication. A controller that reads the flag as the only fault signal will miss a fast transient, and the port current or the output voltage is the more reliable indication of what happened.

The enable threshold sits between 1 V and 2 V with 70 mV to 200 mV of hysteresis, so a 1.2 V GPIO may not turn the part on at the bottom of the window and a 1.8 V GPIO is marginal. The part is intended for 3.3 V or 5 V logic, and a low voltage processor needs a level shifter or a different member of the family whose threshold is specified below 1 V.

Output discharge adds a leakage path to ground while the switch is off, so a port that is meant to hold a voltage with the switch disabled cannot use this order code. On a battery backed rail the 470 ohm pulldown draws about 7 mA at 3.3 V whenever the switch is disabled, which is larger than the sleep current of most of the loads it feeds. That is the trade for the discharge behaviour and it belongs in the standby budget.

The under voltage lockout range of 3.5 V to 4 V means a 5 V rail at minus five percent is 4.75 V, which is above the highest possible release point and therefore safe on any part. The same rail at minus ten percent is 4.5 V, still above 4 V, so a standard 5 V supply has margin. What does not have margin is a 5 V rail that droops during a load step: if the droop reaches 4 V the switch turns off and the port drops, which looks like a fault to the host even though the flag never asserts. A rail that is expected to sag needs its bulk capacitance checked against this threshold.

Where this order code fits

It fits a 5 V port that has to carry more than an amp and has to be discharged at turn off, such as a USB charging port with enumeration, a hot plug card slot or a peripheral bay where a residual voltage would confuse the host. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Will it work on a 3.3 V rail? No, the under voltage lockout releases between 3.5 V and 4 V, so a 3.3 V rail never turns the switch on.

What is the fault current at 5 V? 2.15 A typical, with 1.7 A to 2.5 A over temperature.

How fast does the output discharge? The 470 ohm pulldown removes the charge in a few time constants, so a 10 uF load is down to a few percent in about 50 ms.

Can the flag drive a 3.3 V input? Yes, it is open drain and the pull up can go to 3.3 V as long as the pin rating is respected.

Does it work on a 5 V rail at minus five percent? Yes, 4.75 V is above the 4 V maximum release point of the lockout, so the switch turns on with margin.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.