Contact Us

TPS2066DGN-1

Brand: Texas Instruments
Texas Instruments TPS2066DGN-1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2066DGN-1 — Power Management & Signal Chain | Superb Automation

TPS2066DGN-1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2066DGN-1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2066DGN-1 dual channel 1 A power distribution switch with output discharge in the 8 pin MSOP PowerPAD body

The TPS2066DGN-1 is the dual channel 1 A member of the TPS206x-1 family, which is the variant that adds output discharge to the older dual switch. Two independent 1 A switches share an eight pin MSOP package with an exposed pad, each with its own active high enable and its own fault output. The -1 suffix is not cosmetic: this family discharges the output when a channel is disabled and its rise time is 0.6 ms rather than the 3 ms of the base family, so a board that mixes the two behaves differently at power up and power down.

The reason a board chooses this part over the base TPS2066 is downstream behaviour. A port that has to be pulled down when it is switched off, or a device that has to see a clean reset edge, needs the discharge path. A port that is simply switched and protected does not, and the base family is cheaper. Both parts share the pins and the rating, which makes them easy to confuse on a bill of materials and easy to substitute in an emergency if the difference is understood.

Key parameters taken from the TPS2066DGN-1 document

Rated current1 A per channel on the dual body, both channels able to run at rating together
On resistance70 mOhm typical and 135 mOhm maximum over minus 40 to plus 125 C in the DGN body
Current limit1.1 A minimum and 1.9 A maximum, the accurate fixed limit the -1 family is specified to
Current limit tolerancePlus or minus 20 per cent, quoted in the feature list as 1.1 A minimum and 1.9 A maximum
EnableActive high on the TPS2066-1, with the active low member of the dual family being the TPS2062-1
Rise time0.6 ms typical, against 3 ms on the base TPS2066 family
Output dischargePresent on every -1 member, which is the defining feature of the family
Fault outputOpen drain, active low, deglitched, with no glitch during power up
Standby current1 microamp maximum with the switches off, quoted as a maximum
Supply current75 microamp typical and 95 microamp maximum with the switches on, the same as the base family
Body and packingHVSSOP DGN 8 pins with an exposed pad, 2500 pieces on a 330 mm reel, NIPDAU finish, moisture level 1 unlimited floor life
Order code noteThe published row is TPS2066DGNR-1, with the R before the suffix; the catalogue string on this page is TPS2066DGN-1, which does not appear in the vendor addendum
TemperatureMinus 40 to plus 85 C ambient, junction to 125 C, marking 2066
FamilyTPS2062-1, TPS2065-1 and TPS2066-1 share one document and one set of electrical tables

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The order code on this page needs a note. The vendor addendum for the -1 family lists TPS2066DGNR-1 at 2500 pieces on a large reel in the DGN body, and it does not list a string without the R. The R is the reel letter in this naming scheme, so the catalogue entry as printed cannot be ordered under that exact string. Two possibilities: the catalogue was transcribed without the R, or the part was quoted from a distributor stock list. Either way, the purchase order should carry TPS2066DGNR-1 unless the customer confirms a different packing, and this is the kind of discrepancy we raise before a reel is committed rather than after.

The 0.6 ms rise time is the second difference from the base family, and it changes the inrush calculation. Into a 150 microfarad port capacitor, a 0.6 ms ramp draws a peak current several times the steady state load, which is exactly why the current limit has to be above the inrush and why the discharge family is paired with a limit that starts at 1.1 A. On a board that moved from the base part to the -1 part without rechecking, the port can trip on every plug in. The fix is more output capacitance upstream or a slower enable, not a bigger current limit.

Output discharge on a dual part has a side effect that single channel boards never see. With two channels on one package, both discharge paths share the ground return, so switching both ports off at once pulls both downstream capacitors down through the same pin. On a board with a long ground trace between the package and the connector, that shared return can lift the local ground by tens of millivolts for the duration of the discharge, which a sensitive downstream device may read as a signal. Stagger the two enables if that is a risk.

The standby current of 1 microamp maximum is lower than the base family's 0.5 microamp typical and 1 microamp maximum, which sounds the same and is measured differently: the -1 family quotes only a maximum, so the number can be used directly in a battery budget without a derating factor. On a product that keeps two ports available for a wake event, that is the figure that decides whether the buffer cell lasts a year or five.

  • The order code against the vendor addendum, since the string on the page lacks the reel letter.
  • Inrush current into the real port capacitor at the 0.6 ms rise time, before the current limit is chosen.
  • Discharge behaviour with both channels switching off at once, where the shared ground return can lift locally.
  • Fault flag behaviour at power up, which the family specifies as free of glitches.
  • On resistance on the assembled board at 1 A, since the exposed pad has to be soldered for the published figure to hold.
  • Standby current with both switches off, quoted as a maximum for the battery budget.

Which projects this part fits

This part fits dual USB ports on new boards, instrument front ends where both downstream rails have to be discharged at power off, industrial gateways with two protected peripheral feeds, and any product where a port has to present a clean falling edge to the device behind it. It is also the part to use when a board has to move from the base TPS2066 because a downstream device started misbehaving at power down, since the pins do not change.

Questions that come up before a purchase order is released

What exactly does the -1 suffix change?

Two things. The family adds an output discharge path that pulls the port down when the channel is disabled, and the rise time drops from 3 ms to 0.6 ms. The pins, the rating and the current limit window are the same as the base family, so the suffix is easy to miss on a bill of materials and the behaviour difference only shows at power up and power down.

Is TPS2066DGN-1 an orderable string?

Not on the vendor addendum, which lists TPS2066DGNR-1 at 2500 pieces. We quote and ship against the published string unless the customer's own drawing specifies otherwise, and we flag the difference on the quotation so that the receiving inspection does not reject a correct reel for a label mismatch.

Does the part need a minimum load?

No. The discharge path works with no load, and the switch itself is a MOSFET with no minimum current requirement. The only requirement is that the output capacitor is within the range the discharge path can handle, which the vendor's application section describes as a few hundred microfarad at most for a fast fall.

Can the two channels be ganged?

The enables can be tied together so both channels switch at once, and the vendor shows this configuration. The channels still limit independently, so a short on one does not protect the other. If the product needs both ports off on any fault, the two fault outputs have to drive a gate that pulls the shared enable low.

What happens if the exposed pad is not soldered?

The part still works at light load, and the published on resistance still applies since it is a die figure. What changes is the thermal path: the pad is the main route for heat out of the package, so a 1 A channel that is unsoldered runs much hotter than the data sheet implies. On a dual part with both channels at 1 A, that difference is the margin between a comfortable junction and thermal shutdown.

How SUPERB handles this line

We supply the TPS2066DGNR-1 against the published vendor string and we confirm the reel letter on every order, so a catalogue string without the R does not turn into a wrong delivery. The power management cross reference page sets out the dual switches with their discharge behaviour noted, pin to pin cross reference covers the move between the base and the -1 family, and incoming inspection plan describes the label and marking checks we run on a delivery like this.