Contact Us

TPS2065DDBVR

Brand: Texas Instruments
Texas Instruments TPS2065DDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2065DDBVR — Power Management & Signal Chain | Superb Automation

TPS2065DDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2065DDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2065DDBVR 1 A power distribution switch with an active high enable, output discharge and reverse current blocking in the 5 pin SOT-23 body

The TPS2065DDBVR is a single channel 1 A switch from the newer TPS206xD family, in the same five pin SOT-23 body as the older parts but with a different set of features inside. It has an active high enable, output discharge, reverse current blocking, a built in soft start and a fault output that is deglitched. In practice it is the part that replaces the older 1 A switches on new boards, because it does everything they did plus the discharge and the reverse blocking that modern products expect.

The current limit is tighter than the older family and the response is faster: a plus or minus 20 per cent window around a fixed level, with a two microsecond response to a short. The switch element is 96 mOhm typical in this body, which is higher than the 70 mOhm of the SOIC and MSOP members of the older family, but the five pin body is what most boards have room for. The trade between package size and on resistance is the first decision on a 1 A port.

Key parameters taken from the TPS2065DDBVR document

Rated current1 A continuous on the single channel
On resistance96 mOhm typical and 110 mOhm maximum at 25 C in the DBV body
On resistance over temperature96 mOhm typical and 130 mOhm maximum from minus 40 to plus 85 C
Current limit at 25 C1.3 A minimum, 1.55 A typical and 1.8 A maximum on the 1 A rated output
Current limit over temperature1.2 A minimum, 1.55 A typical and 1.9 A maximum
Current limit tolerancePlus or minus 20 per cent, fixed, with a 2 microsecond typical overcurrent response
EnableActive high, with a rising threshold of 1 V minimum, 1.45 V typical and 2 V maximum, and 70 to 200 mV of hysteresis
Enable leakageStated in the document as a leakage current rather than a drive current, so the pin can be driven from a microcontroller without a buffer
Output dischargePresent, so a disabled port is pulled down through an internal path
Reverse current blockingThe switch blocks current from output to input while off, and the reverse path is described in the application section
Fault outputOpen drain, active low, deglitched, asserted in current limit and in thermal shutdown
Body and markingSOT-23 DBV 5 pins, marking 18OF, 3000 pieces on a large reel or 250 on a small reel
Moisture levelLevel 2, 260 C, one year floor life, which is tighter than the level 1 of the older family
TemperatureMinus 40 to plus 85 C ambient, junction to 125 C, and UL listed under file E169910

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The enable threshold is worth a look before the part is wired to a microcontroller that runs from a lower rail. The rising threshold is 1 V minimum and 2 V maximum, so a 1.8 V logic high can fail on a part at the top of that window, and a 3.3 V host has no problem at all. The hysteresis is 70 to 200 mV, which is wide enough that a slow rising enable signal will not chatter, but a signal that crosses the threshold once and then sags below it will not turn the port off either. Drive the pin from a push pull output rather than from a divider.

Output discharge is the feature that most boards actually notice. When the port is switched off, the output is pulled down, so the downstream device sees a rail collapsing rather than a rail that stays up on its own capacitance. On a USB port that is the difference between a device re-enumerating and a device that sits half powered. The discharge path is a small current source rather than a hard short, so the fall takes milliseconds and the node does not ring.

The fastest limit in the family, 1.3 A minimum at room temperature, sits only 30 per cent above the 1 A rating. That is deliberate, and it means a load with a wide tolerance can cross the limit on a cold board. A downstream device that draws 1.2 A in a peak will not trip a typical part at 25 C but can trip a part at the bottom of the window at 85 C, where the limit falls to 1.2 A. If the load is that close to the rating, the 1.5 A member of the wider portfolio is the honest choice rather than a tighter limit here.

The reverse blocking is a genuine function and not a side effect. When a port is unpowered and the downstream device holds its own supply, the switch prevents that supply from feeding back into the 5 V rail, which would otherwise keep the whole board half alive. The behaviour depends on the switch being off, so a port that is left enabled with the main rail down is not protected. In a product that has to survive a main supply loss, the enable has to follow the main rail rather than the host rail.

  • Current limit at the cold and hot corners, since the window runs 1.2 to 1.9 A over the ambient range.
  • Enable threshold on the actual host rail, where a 1.8 V logic high is inside the published window and not guaranteed.
  • Output discharge at power down, measured on the real downstream capacitance, because the fall is a current source and not a short.
  • Reverse blocking with the port unpowered and the downstream device powered from its own source.
  • The fault flag through a plug in event, which must stay released through the inrush.
  • Moisture handling on the line, because this body is level 2 with a one year floor life rather than level 1.

Which projects this part fits

This part fits single USB and peripheral ports on new boards, instrument and medical device ports where the downstream node has to be discharged at power off, battery powered products where a port must not feed back into the main rail, and any board that needs a fault report from a 1 A port in a five pin footprint. It is also the part that replaces the older 1 A switches on a board that is being refreshed, since the pins match and the features are a superset.

Questions that come up before a purchase order is released

Can it drop into a TPS2061 socket?

Yes on the pins, but the enable sense is inverted. The TPS2061 is active low and this part is active high, so the firmware or the driving circuit has to change. The current limit is also different, 1.3 to 1.8 A here against 1.1 to 1.9 A there, so the test limit for the port has to be rechecked rather than copied from the old drawing.

How does the discharge behave when the port is enabled again?

The discharge path releases when the switch turns on, so there is no shoot through. The upstream rail then has to charge the downstream capacitance through the switch, and the soft start limits that inrush. A port with a large downstream capacitor still draws a current spike at turn on, and the switch limits it rather than latching off.

What is reverse current blocking actually protecting?

The main rail. Without it, a downstream device that holds its own supply, a battery powered accessory for example, feeds current back through the switch body diode into the 5 V rail and keeps the board partly powered after the supply is removed. With it, the port is isolated once the switch is off. The function does not protect a port that is left on.

Why is the moisture level 2 and not 1?

Because of the body and the lead frame finish of this family. Level 2 with a one year floor life means the parts have to be kept dry and the floor life tracked after the bag is opened, and a board that reflows after the floor life has to be baked. Level 1 parts from the older family do not have that constraint, which matters on a line that opens and closes reels over weeks.

Is the part suitable for a 1.5 A port?

No. The rating is 1 A and the current limit window starts at 1.2 A over temperature, so a genuine 1.5 A load would sit in limit. The portfolio has 1.5 A and 2 A members, and the honest answer for a port above 1 A is a different part number rather than a tighter test limit on this one.

How SUPERB handles this line

We supply the TPS2065DDBVR on original reels with the marking 18OF and the date code recorded, and we track the floor life on the level 2 bodies so that a delivery arrives inside its window. The power management cross reference page lists the port switches with their discharge and blocking features called out, medical device components covers the port protection we support on instrument builds, and date code management explains the floor life records that travel with a delivery.