Contact Us

TPS2061DBVR

Brand: Texas Instruments
Texas Instruments TPS2061DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2061DBVR — Power Management & Signal Chain | Superb Automation

TPS2061DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2061DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2061DBVR 1 A power distribution switch with an active low enable in the 5 pin SOT-23 body

The TPS2061DBVR is the 1 A, active low single channel switch of the TPS206x family, in the five pin SOT-23 package. It is the part most boards use when a port has to be switched from an open collector signal or a pin that goes low on reset, and when the 500 mA of the smaller family is not enough. The die is the same core as the rest of the TPS206x family, with a 70 mOhm high side MOSFET, a current limit and a deglitched fault output.

The family sits between the low current B parts and the higher current TPS2068 and TPS2069, and it is the 1 A step that most USB and peripheral ports land on. Unlike the newer TPS206x-1 variant, this part has no output discharge, so a disabled port floats rather than being pulled down. That is the main functional difference to check when a bill of materials mixes the two suffixes.

Key parameters taken from the TPS2061DBVR document

Rated current1 A continuous, the middle rating of the TPS206x family
On resistance70 mOhm typical and 135 mOhm maximum over minus 40 to plus 125 C in the D and DGN bodies
On resistance in this body95 mOhm typical and 140 mOhm maximum in the DBV five pin SOT-23, which is the body this order code uses
On resistance at 2.7 V75 mOhm typical and 150 mOhm maximum in the D and DGN bodies
Current limit at 25 C1.1 A minimum, 1.5 A typical and 1.9 A maximum with the output grounded
Current limit over temperature1.1 A minimum, 1.5 A typical and 2.1 A maximum
EnableActive low on the TPS2061, with the active high member at the same rating being the TPS2065
Supply current75 microamp typical and 95 microamp maximum with the switch on, 0.5 and 1 microamp with it off
Turn on and turn off3 ms typical turn on and 10 ms typical turn off into 100 microfarad with a 5 Ohm load
Fault outputOpen drain, active low, deglitched, asserted in current limit and in thermal shutdown
Output dischargeNot present on this part, which is the difference to the TPS2065D and the TPS206x-1 family
Reverse blockingThe switch blocks current from output to input while it is off
Body and packingSOT-23 DBV 5 pins, 3000 pieces on a 180 mm reel, NIPDAU finish, moisture level 1 unlimited floor life, marking 2061
Temperature gradeMinus 40 to plus 125 C junction on the orderable row, minus 40 to plus 85 C ambient operating range

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The on resistance row for the five pin body is the one that matters here, and it is 95 mOhm typical against 70 mOhm in the larger packages. At 1 A that is 95 mV of drop and 95 mW of heat, in a package with no thermal pad and a thermal resistance near 250 C per watt. The junction sits about 24 C above the board, which is acceptable at 25 C ambient and uncomfortable inside a sealed enclosure at 70 C. A 1 A port in this body is a 1 A port on paper, and the board has to give it copper.

The current limit window on the 1 A members runs 1.1 to 1.9 A at room temperature and 1.1 to 2.1 A over ambient. The bottom of the window is useful: a 1 A port that draws 1.05 A continuously will not trip a warm part, but a 1.2 A load can trip a part at the bottom of the window. If the downstream load has a wide tolerance, the minimum figure is the one to compare against, and the answer may be that the port needs the 1.5 A member of the same family rather than a tighter limit.

The absence of output discharge is the difference to catch when a bill of materials is being updated. On a board that was built with the TPS2065D, the downstream node is pulled down at power off, and a device that senses its own rail sees a clean reset. With the TPS2061 fitted instead, that node floats and holds whatever charge the downstream capacitance keeps, which can leave a device half alive for minutes. Both parts look the same on a drawing and behave differently at power down, and that is exactly the kind of substitution that passes a bench test and fails in the field.

The fault output is deglitched, which is what makes the part usable with a 150 microfarad port capacitor. The vendor also states that the flag does not glitch during power up, which matters on a board where the host rail comes up before the 5 V rail: the flag stays released until the switch is actually enabled, so the host does not count a phantom fault at every cold start. If the flag is pulled up to the switched output instead of the host rail, that behaviour is lost.

  • Current limit at the top and bottom of the ambient range, since the window opens to 2.1 A over temperature.
  • On resistance in the SOT-23 body at 1 A, where the package thermal resistance is the limiting factor.
  • The fault flag during power up, which must stay released until the switch is enabled.
  • Behaviour at power down, because this part does not discharge the output and a downstream device may stay partly alive.
  • Reverse blocking with the port unpowered, which the family provides while the switch is off.
  • The enable pin state before the host drives it, since an active low enable with a floating pin turns the port on.

Which projects this part fits

This part fits single 1 A ports on industrial and consumer boards, peripheral rails on set top boxes and televisions, sensor and actuator supplies where a hard limit is needed, and any board where a port is switched from an active low signal such as a reset line or an open collector comparator. It also serves as the 1 A step between the 500 mA family and the 1.5 A parts when a port rating has to grow without a change of footprint.

Questions that come up before a purchase order is released

Does this part have output discharge?

No. The TPS206x family, of which this is a member, does not discharge the output when the switch is off. The discharge function belongs to the TPS206x-1 family and to the TPS2065D, which carry it in the same five pin body. If a board needs the port pulled down at power off, the order code has to change to one of those.

Can the TPS2065 replace the TPS2061?

Yes on the pins and the rating, and the only difference is the enable sense: the TPS2061 is active low and the TPS2065 is active high. A board that drives the enable from a host pin has to invert the firmware, and a board that drives it from a resistor divider has to be reworked. The current limit and the thermal behaviour are the same.

What is the fault output rated for?

It is an open drain output meant for a logic level pull up. It is not rated to drive a relay or an LED directly, and it is not a push pull output, so it cannot be used to hold another device's enable low without an external transistor. In practice it drives a host input with a 10 k to 100 k pull up.

How much copper does a 1 A port need?

Enough that the junction stays below the thermal limit at the ambient inside the enclosure. At 1 A and 140 mOhm maximum the dissipation is 140 mW, and with a thermal resistance near 250 C per watt the junction sits 35 C above the board. On a 70 C ambient that is 105 C, inside the 125 C rating but with little margin. Doubling the copper under the part is cheaper than a larger package.

What is the difference between the DBVR and the DGNR order codes?

The package. The DBVR is the five pin SOT-23 on a 3000 piece reel, and the DGNR is the eight pin MSOP with an exposed pad on a 2500 piece reel. The MSOP body has the better thermal path, so a 1 A port that runs hot is usually moved to the DGN body rather than to a different part number.

How SUPERB handles this line

We supply the TPS2061DBVR on original 3000 piece reels with the marking and date code recorded against the delivery, and we keep the MSOP body of the same part number for boards that need the better thermal path. The power management cross reference page groups the port switches by rating, how to verify a drop in replacement covers the check we run when a customer wants to move between the discharge and non discharge members, and excess inventory management is the route when a build ends and a partial reel is left over.