TPS2051BD
Product Specifications
TPS2051BD
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2051BD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2051BD 0.5 A single channel power distribution switch with an active high enable in the 8 pin SOIC body
The TPS2051BD is the active high, 500 mA member of the TPS20xxB family in the 8 pin SOIC package. It is the part that many industrial boards reach for when a port has to be switched from a microcontroller pin that idles low, since a high on the enable turns the switch on and the pin can be left pulled down through a reset. The B family is the generation before the C revision and it remains in production, which is why it still shows up on drawings that were released years ago.
The electrical behaviour is the familiar one for this family: a 70 mOhm high side MOSFET, a current limit that holds constant current, a thermal cut out that recovers on its own, an undervoltage lockout and an open drain fault output. What separates the B from the C is the accuracy and the speed of the current limit, and the presence of output discharge on every member rather than on a selected subset. On a board that only needs a port switched and protected, none of those differences change the result.
Key parameters taken from the TPS2051BD document
| Rated current | 500 mA continuous on the single channel members |
| On resistance | 70 mOhm typical on the 5 V and 3.3 V rows in the D and DGN bodies, 135 mOhm maximum over minus 40 to plus 125 C |
| On resistance in the small body | 95 mOhm typical and 140 mOhm maximum in the DBV package, which is the five pin SOT-23 |
| On resistance at 2.7 V | 75 mOhm typical and 150 mOhm maximum in the D and DGN bodies |
| Current limit at 25 C | 0.75 A minimum, 1 A typical and 1.25 A maximum with the output grounded |
| Current limit over temperature | 0.7 A minimum, 1 A typical and 1.3 A maximum |
| Enable | Active high on the TPS2051B, with the active low member at the same rating being the TPS2041B |
| Supply current | 75 microamp typical and 95 microamp maximum with the switch on at 25 C, 0.5 and 1 microamp with it off |
| Turn on and turn off | 3 ms typical turn on and 10 ms typical turn off into a 100 microfarad load with a 10 Ohm resistor |
| Fault output | Open drain, active low, asserted in current limit and in thermal shutdown |
| Output discharge | Present on the B family, so a disabled port is pulled down |
| Body | SOIC 8 pins in the D package, with the DBV and DGN bodies used by the other members of the family |
| Temperature | Minus 40 to plus 85 C ambient on the operating range, junction to 125 C |
| Family position | The 500 mA single is the entry rating, with 1 A, 1.5 A and 2 A members in the same document |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The difference between the 70 mOhm in the SOIC and the 95 mOhm in the SOT-23 is bigger than the numbers suggest on a 5 V port. At 500 mA, 70 mOhm costs 35 mV and 95 mOhm costs 47 mV, and the maximum values over temperature are 135 and 140 mOhm, which cost 67 and 70 mV. A USB port has to deliver 4.4 V at the connector under load, so the drop through the switch is one line in a budget that also includes the cable, the connector and the trace. On a board that is already tight, the package choice is worth 30 mV.
The current limit on the B family is looser than on the C family, and the window is asymmetric around the nominal. A 0.5 A part limits between 0.75 and 1.25 A at room temperature and 0.7 to 1.3 A over ambient, so a downstream load of 800 mA may or may not trip depending on the lot. That sounds like a defect and is actually the specification: the limit is there to protect the upstream rail, not to act as a precise current source. A product that needs a predictable trip point needs a different part, and a product that needs protection only needs this one.
The turn on and turn off times are not symmetric and that asymmetry matters for a host that switches a port off during a fault. Rise is 3 ms and fall is 10 ms into the same load, because the discharge path is weaker than the charge pump. During the 10 ms fall the port voltage passes through the whole range, so a downstream device sees a slow ramp down rather than a clean break. On a device that does not tolerate a slow ramp, the port needs a hard disconnect or the downstream device needs its own undervoltage lockout.
The supply current with the switch on is 75 microamp typical and 95 microamp maximum, and with it off it falls to half a microamp typical and one microamp maximum. On a board with eight ports that is 0.8 mA of standing current, which a mains supply does not notice and a battery does. The off figure is the one to quote in a standby budget, and it is a maximum rather than a typical, so it can be used directly.
- Current limit at both ends of the ambient range, since the B family window is 0.7 to 1.3 A on a 0.5 A part.
- On resistance in the body actually used, because the SOIC and the SOT-23 differ by 25 mOhm typical.
- Turn off time into the real load, since a 10 ms fall is slow enough to matter to a downstream device.
- Fault flag behaviour at power up, where the pull up rail decides whether the host sees a false fault.
- Standby current with the switch off, quoted as a maximum for the battery budget.
- Reverse blocking with the port unpowered, which the family provides while the switch is off.
Which projects this part fits
This part fits industrial control boards where a port is switched from a microcontroller pin, telecom line cards with several protected feeds, test equipment where each channel under test needs its own limited supply, and legacy boards in long production that were released around the B family and cannot take a change of silicon without a requalification. It also serves as the practical substitute when the C revision is not on the shelf, since the pins and the function are the same and only the accuracy of the limit changes.
Questions that come up before a purchase order is released
Can a TPS2051C replace the TPS2051B?
On the pins and the function, yes, and the C part is the tighter and faster of the two. The two differences that matter are the current limit window, which is narrower on the C, and the response time, which is 2 microseconds on the C against a slower figure on the B. A board that trips on the B at 0.8 A will trip on the C at a different point, so the test limit has to be rechecked rather than copied.
Why is the on resistance so different between packages?
Because the package is part of the resistance. The SOIC 8 and the MSOP 8 have wider lead frames and a thermal pad, and the five pin SOT-23 has thin leads and no pad. The die is the same. The vendor publishes separate rows for each body rather than one number, and the row for the body on the board is the one to use.
Is the fault output push pull?
No, it is open drain and needs a pull up. The pull up can go to the host rail or to the input rail, but not to the switched output, because then the flag reads as asserted until the switch turns on and the host logs a fault on every power up.
What happens on a sustained short?
The switch holds constant current, the die heats, thermal shutdown opens the switch, the die cools and the cycle repeats. The fault pin follows the switch, so the host sees a train of pulses rather than a steady low. Firmware that counts edges can distinguish a real short from inrush, which is a single event.
Is this part rated for automotive use?
No. The B family is specified over minus 40 to plus 85 C ambient with a commercial qualification. Automotive boards need the Q1 members of the portfolio, which carry a different temperature grade and a different qualification record. We do not offer this part number for an automotive bill of materials.
How SUPERB handles this line
We supply the TPS2051BD on original reels with the date code and marking recorded, and we keep the active low sibling and the higher current members of the same family available so a port change does not force a new supplier. The power management cross reference page sets out the family by rating and enable sense, one stop BOM sourcing covers the case where this switch sits on a bill with a hundred other lines, and supplier quality audit describes how we qualify the channel that supplies a part like this one.