Contact Us

TPS2041CDBVR

Brand: Texas Instruments
Texas Instruments TPS2041CDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2041CDBVR — Power Management & Signal Chain | Superb Automation

TPS2041CDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2041CDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2041CDBVR 0.5 A single channel power distribution switch with an active low enable in the 5 pin SOT-23 body

The TPS2041CDBVR is the 0.5 A single channel member of the TPS20xxC family, in the five pin SOT-23 body that most USB port protection on small boards uses. It carries an active low enable, an open drain fault output, output discharge and reverse current blocking, so it covers everything a single port needs in a package smaller than a grain of rice. The C revision is the current silicon, and its limits are tighter than the older B family that it replaced in most sockets.

The switch element is a 70 mOhm N channel MOSFET with a current limit that holds the output in constant current rather than opening. Two details make this revision easier to use than its predecessors: the output is discharged when the switch is disabled, and the fault output is deglitched so that inrush into a downstream capacitor does not produce a false fault. Both matter on a port that a user plugs into while the board is running.

Key parameters taken from the TPS2041CDBVR document

Rated current0.5 A continuous, the lowest of the three ratings in the single channel family
On resistance97 mOhm typical and 110 mOhm maximum at 25 C in the DBV body, measured on the 0.5 A rated output
On resistance over temperature96 mOhm typical and 130 mOhm maximum from minus 40 to plus 85 C
Current limit at 25 C0.67 A minimum, 0.85 A typical and 1.01 A maximum on the 0.5 A rated output
Current limit over temperature0.65 A minimum, 0.85 A typical and 1.05 A maximum
Current limit tolerancePlus or minus 20 per cent, the family specification, with a 2 microsecond typical response
EnableActive low on the TPS2041C, with the active high member of the same rating being the TPS2051C
Output dischargePresent, so a disabled port is pulled down rather than left floating
Fault outputOpen drain, active low, deglitched, released when the channel returns to normal current
Reverse current blockingThe switch blocks current from output to input while off
Body and markingSOT-23 5 pins in the DBV package, marking PYJI, 3000 pieces on a large reel
Moisture levelLevel 1, 260 C, unlimited floor life on the DBVR row
Temperature gradeMinus 40 to plus 125 C junction on the orderable row, with a minus 40 to plus 85 C ambient operating range
Order codeTPS2041CDBVR is Active and in production on the current addendum
Equivalent family membersTPS2000C, TPS2001C, TPS2051C, TPS2061C, TPS2065C, TPS2068C and the two C-2 parts share the document

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The on resistance in this body is worse than in the larger packages, and the document says so plainly. The 0.5 A rated output in the SOT-23 5 measures 97 mOhm typical and 110 mOhm maximum at 25 C, against 70 mOhm on the SOIC and MSOP bodies of the higher rated members. At half an amp, 110 mOhm is 27 mV of drop and 27 mW of heat, which is harmless. The number matters when a board tries to use this body at 1 A: the 1 A rated output in the same package measures 96 and 110 mOhm at 25 C but 130 at the hot corner, and the temperature rise in a five pin body with no thermal pad is the limiting factor, not the electrical rating.

The current limit window around a 0.5 A rating runs from 0.67 to 1.01 A at room temperature and 0.65 to 1.05 A over ambient. A downstream device that draws 600 mA in a peak will not trip a typical part but can trip a part at the bottom of the window, so the peak current has to be compared against the minimum rather than against the nominal. This is the single most common reason a port that works on the bench fails in the field on a cold morning: the limit moves with temperature and the load moves the other way.

Output discharge is a quiet feature with a visible effect. When this part is disabled, the output is pulled down through an internal path, so a downstream module that holds a capacitor does not see a floating rail. On a port where the downstream device is powered from the same rail and senses it, that fast discharge can look like a reset pulse, which is usually what the host wants. It also means the port cannot be used as a diode OR, since the discharge fights any other source on the same node.

The fault output is deglitched, and the deglitch window is what makes the part usable with a capacitive load. Without it, the inrush into 150 microfarad would assert the flag for the duration of the ramp and the host would report a fault on every plug in. With it, the flag only follows a fault that lasts longer than the filter. A genuinely shorted port still asserts within microseconds of the current limit being reached, so the protection is unchanged.

  • Current limit at the cold corner and the hot corner, since the window moves in both directions around the nominal.
  • On resistance in the SOT-23 body at the actual load, where the package is the thermal limit rather than the die.
  • The fault flag during plug in, which must stay released through the inrush of the port capacitor.
  • Output discharge behaviour at power down, since a downstream device may read the discharge as a reset.
  • Reverse blocking with the port unpowered and the downstream device holding its own supply.
  • Enable pin state during power up, because an active low enable with a floating pin turns the port on.

Which projects this part fits

This part fits single USB ports on small boards, sensor and radio module rails in handheld products, battery powered instruments where a peripheral has to be switched off completely, and any board where the five pin footprint is the space budget. It is also the part to reach for when a board already uses the TPS2051C and the port needs a different enable polarity without a change of footprint, since the two differ only in that pin's sense.

Questions that come up before a purchase order is released

Is the 0.5 A rating enough for a USB 2.0 port?

For a standard 500 mA port it is exactly the rating, with no headroom. A port that has to deliver 500 mA continuously at 5 V with a 4.5 V minimum input has 0.5 V of drop available, and 110 mOhm uses 55 mV of it, which is fine. The issue is the current limit: at the bottom of the window, 0.65 A, a 600 mA load trips. If the port must guarantee 500 mA, the 1 A member of the same family is the safer choice.

What does the C revision change against the B family?

The C parts improve the current limit accuracy, add a faster overcurrent response and, on the C-2 members, remove the output discharge. The pinout is unchanged, which is why the two families are often substituted, but the fault timing and the discharge behaviour differ and a board that relies on either has to be checked.

Can the flag drive an LED directly?

No. The flag is an open drain output rated for logic level currents, and an LED needs more than it can sink. Drive the LED from a transistor, or drive it from the host pin and use the flag as an interrupt. The pin is also not rated for a capacitive load, so a long trace to a front panel needs a series resistor.

Why does the part get warm at 500 mA?

Because the SOT-23 body has no thermal pad. At 500 mA through 110 mOhm the dissipation is 27 mW, which is small, but the thermal resistance of a five pin SOT-23 to ambient is around 250 C per watt, so the junction sits 7 C above the board. The number stays comfortable. The part that gets warm is the 1 A member in the same body, where the same arithmetic gives 110 mW and a junction 28 C above the board.

What is the difference between the DBVR and the DBVT suffix?

The reel size. The R suffix is the 3000 piece large reel and the T suffix is the 250 piece small reel. The part is the same, the marking is the same, and a prototype build can take the small reel without any change to the board.

How SUPERB handles this line

We supply the TPS2041CDBVR from original reels with the marking and date code recorded, and we keep the active high sibling on the same shelf so that a port polarity change does not become a supply problem. The power management cross reference page lists the single channel switches by rating, enable sense and package, date code management explains how we record the lot against a delivery, and safety stock planning covers the buffer we hold on the parts that appear on several customer bills at once.