Contact Us

TPS2010ADR

Brand: Texas Instruments
Texas Instruments TPS2010ADR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2010ADR — Power Management & Signal Chain | Superb Automation

TPS2010ADR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2010ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2010ADR 0.2 A power distribution switch with an active low enable in the 8 pin SOIC body

The TPS2010ADR is the smallest member of the TPS201xA family, a 0.2 A high side switch in an 8 pin SOIC package. It has been in production since the late nineteen nineties and it is still bought because it does one narrow job well: it puts a hard current limit and a thermal cut out between a 2.7 to 5.5 V rail and a small load, with an enable pin and no other moving parts. Boards that were laid out around this part stay around this part, and that is the main reason it still appears on purchase orders.

Inside the package is a 50 mOhm N channel MOSFET, a charge pump that generates the gate drive from the input rail without external components, a current sense element and a thermal sensor. There is no fault output on this member, which is the main thing that separates it from the TPS202x family: the TPS2010A limits and shuts down on thermal events, but it does not tell the host that it did. On a load that a user can short, that silence has to be handled by the host measuring the downstream rail.

Key parameters taken from the TPS2010ADR document

Rated current0.2 A maximum continuous load at 25 C, the lowest rating in the family
Short circuit limit0.22 A minimum, 0.3 A typical and 0.4 A maximum at 25 C, measured with the output grounded and the device enabled into the short
Input range2.7 to 5.5 V, with the charge pump allowing full gate drive at the bottom of that range
On resistance37 mOhm typical and 41 mOhm maximum at 5 V in and 0.18 A at 25 C, which is the 33 mOhm headline rounded to its test condition
On resistance over temperature43 mOhm typical and 52 mOhm maximum at 5 V in at 85 C, and 51 and 61 mOhm at 85 C on a 3.3 V rail
Headline on resistance33 mOhm typical at 5.5 V in, quoted in the feature list with no current or temperature condition attached
EnableActive low, so pulling the enable pin to ground turns the switch on and a logic high turns it off
Rise and fall time6.1 ms typical rise and 3.4 ms typical fall, set by the internal charge pump rather than by an external capacitor
Turn on delay20 ms typical into a 10 Ohm load with a 100 microfarad output capacitor
Standby current10 microamp maximum with the switch off, which is a maximum and not a typical
ProtectionCurrent limit into constant current mode, then thermal shutdown with automatic recovery, and an undervoltage lockout that keeps the switch off until the input is valid
Reverse pathNo drain to source back gate diode, so the switch blocks in both directions while off
ESD2 kV human body model and 200 V machine model
BodiesSOIC 8 pins in the D package and 14 pin HTSSOP in the PWP package, with the R suffix marking a taped and reeled SOIC
TemperatureMinus 40 to plus 85 C ambient, with the junction allowed to reach 125 C

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The absence of a fault output changes how the part is used. On the TPS202x family the same die drives an open drain flag, and a host can count short circuits. On the TPS2010A the only evidence of a fault is the downstream rail collapsing and then recovering after thermal shutdown, and if the firmware does not watch that rail it will report a healthy port. In practice this part is chosen where the load cannot be shorted by a user, for example an internal sensor rail or a fixed daughter card, and the TPS202x is chosen where a cable can be pulled or a connector can be misaligned.

The current limit is close to the rated current, which is unusual and worth understanding. A 0.2 A part whose limit at 25 C runs from 0.22 to 0.4 A has almost no headroom between its continuous rating and its guaranteed trip point, so a load that draws 0.2 A with a 20 per cent tolerance can sit in current limit at the hot corner without any fault being present. The family is built this way on purpose, since a tight limit is what protects the upstream regulator, but a load with a wide current tolerance belongs on the 0.6 A member instead.

The on resistance figures need the test condition attached. The feature list quotes 33 mOhm, the electrical table quotes 37 mOhm typical at 0.18 A and 5 V, and the same table shows 52 mOhm maximum at 85 C. At 0.2 A the difference between 33 and 52 mOhm is 0.004 W, which is nothing, so the thermal question on this part is not the switch but the body. An SOIC 8 dissipates about 725 mW at 25 C on a board with a reasonable copper area, and that is far above anything a 0.2 A switch will reach.

The reverse blocking behaviour catches people out during power sequencing. With no back gate diode, the switch blocks current from output to input while it is off, so a downstream rail that is held up by its own storage capacitor cannot feed back into the main rail. That is useful on a board where a peripheral has a local battery or a large bulk capacitor. It also means a bleed resistor or the load itself is the only path to discharge that capacitor, and the rail can stay high long after the switch is disabled.

  • The current limit at 85 C on the actual load, since the 25 C window is 0.22 to 0.4 A and the load tolerance may already overlap it.
  • The state of the downstream rail after a fault, because this member gives no flag and the rail is the only indication.
  • Rise time into the real output capacitance, since the 6.1 ms figure is quoted for a 1 microfarad load in some rows and the timing scales with the capacitor.
  • Behaviour at 2.7 V in, where the gate drive is at its weakest and the on resistance is at its highest.
  • Reverse leakage with the switch off and the output held high by another source.
  • The enable pin level during power up, since an active low enable with a floating pin turns the switch on.

Which projects this part fits

This part fits internal rails on industrial and telecom boards, small peripheral supplies where the load cannot be shorted by a user, legacy boards that were routed for the SOIC 8 footprint and are being kept in production, and any product where a hard current limit is needed with no software involvement at all. It also serves as a drop in replacement on boards that were built around the earlier TPS201x revision, since the pinout and the timing have not changed across the revisions.

Questions that come up before a purchase order is released

Can a TPS2022 replace a TPS2010A on the same footprint?

Yes on the pins, no on the current. The TPS202x family carries an overcurrent output on pin 5 where the TPS201xA family has a no connect, so the flag can be picked up on an existing board if that pad is routed or can be bridged. The rated current of the TPS2022 is 1 A against 0.2 A here, so the limit is five times higher and a load that relied on the tight 0.3 A limit loses that protection.

Why is the standby current given as a maximum only?

Because the parameter is dominated by leakage that varies from lot to lot and rises with temperature, so the vendor guarantees a ceiling instead of a typical. Ten microamp is the number for a battery life calculation. On a 3.3 V rail that is 33 microwatt, which is small but not zero, and a product that sleeps for a year will notice it.

What happens if the output is shorted while the part is on?

The switch moves into constant current mode at the limit, the die heats, thermal shutdown opens the switch at the junction limit, and the cycle repeats as the die cools. There is no latch, so a permanent short produces a repeating hiccup with no signal to the host. The upstream regulator has to tolerate that duty cycle, and the board has to be able to survive the thermal cycling.

Is the part suitable for a 5 V USB port?

Only for a very small one. A USB port has to supply 500 mA and survive a user shorting it, and this part is rated 0.2 A. The TPS2051B or the TPS2065D are the members of the wider portfolio that carry the 500 mA rating with a fault flag, and the pinout differs, so the board has to change.

What is the marking on the body?

The SOIC body carries the device name and a date code, and the reel label carries the full orderable string. We record both against the lot, because the same footprint is used by several members of the family and a rework station can mix them.

How SUPERB handles this line

We supply the TPS2010ADR from original reels with date code traceability and we hold the family's other members alongside it, since a board that uses one usually uses two or three. The obsolete part cross reference hub is the page to start from when an older switch like this one goes end of life, power management cross reference lists the current limited switches by rating and package, and component lead time solutions covers the case where the reel is quoted at a long lead time and the build cannot wait.