Contact Us

TPS2003CDRCR

Brand: Texas Instruments
Texas Instruments TPS2003CDRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2003CDRCR — Power Management & Signal Chain | Superb Automation

TPS2003CDRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2003CDRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2003CDRCR dual channel 2 A power distribution switch in the 10 pin VSON body

The TPS2003CDRCR is the 2 A member of the TPS20xxC dual family, a pair of high side N channel MOSFET switches in one 3 by 3 mm VSON package. Each channel is controlled by its own enable input, both inputs are active high on this part number, and each channel has its own fault flag. The intended job is to sit between a 5 V rail and two downstream loads that a host has to be able to switch off, current limit and report on separately, which is why the part turns up on USB hub boards, set top boxes, digital televisions and industrial control cards that feed several peripherals from one supply.

Two things separate this device from a plain load switch. The first is the current limit: when a channel is overloaded the switch moves into constant current mode instead of latching off, so a shorted port pulls a bounded current and the upstream 5 V supply keeps regulating. The second is the fault flag, which is deglitched and open drain, so the host sees a clean asserted signal rather than a burst of edges on the first inrush event. Both behaviours are the reason this family is still chosen for ports that a user can plug into while the product is running.

Key parameters taken from the TPS2003CDRCR document

Rated current2 A per channel, the highest rating in the dual family, with 0.5 A, 1 A and 1.5 A members in the same document
Input range4.5 to 5.5 V operating, which is a 5 V rail part and not a wide input device
On resistance70 mOhm typical and 95 mOhm maximum at 25 C, on the 2 A members, measured at 5 V in
On resistance over temperature70 mOhm typical and 112 mOhm maximum from minus 40 to plus 85 C ambient
Current limit at 25 C2.55 A minimum, 3.15 A typical and 3.77 A maximum on the 2 A parts
Current limit over temperature2.35 A minimum, 3.15 A typical and 3.95 A maximum, a wider window than the 25 C row
Current limit tolerancePlus or minus 20 per cent against the nominal, which is what the family is specified to
Short circuit response2 microseconds typical from the fault to the current falling below 120 per cent of the final value
Supply current60 microamp typical and 75 microamp maximum with one channel on, 100 and 120 microamp with both on, 0.01 and 1 microamp with both off
EnableActive high on the TPS2003C, with the low enable member of the same family being the TPS2002C
Output dischargePresent on this part, so a switched off port is pulled down instead of floating
Undervoltage lockout4.0 V typical on the input, with hysteresis that is stated in the document but not given as a single number
Thermal shutdown135 C junction, entered while the part is in current limit and released automatically once it cools
Body and packingVSON DRC 10 pins, 3 by 3 mm, 3000 pieces on a 330 mm reel, NIPDAU finish, moisture level 1 unlimited floor life
Temperature gradeMinus 40 to plus 125 C junction on the orderable row, against a minus 40 to plus 85 C ambient operating range

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The current limit window is the number to build a port around, and it is wider than most people assume. The 25 C row gives 2.55 to 3.77 A, but the row that runs across the full ambient range opens to 2.35 to 3.95 A. A board that budgets a 3.3 A adapter behind this switch therefore has to survive a 3.95 A pass element current at the hot corner, and it also has to accept that a 2.4 A load is inside the guaranteed window and will not trip at all. The fault is a limit, not a fuse, and the host has to know how long a limited channel may stay limited before software shuts the port down.

On resistance has two readings in the same document, and both matter. The 25 C figure of 70 mOhm typical is what a bench measurement shows, and the 112 mOhm maximum over ambient is what the thermal calculation needs. At 2 A through a channel, the difference between 70 and 112 mOhm is 0.28 W against 0.45 W in a 3 by 3 mm body, which moves the junction temperature by tens of degrees once the board is inside an enclosure. The VSON body has an exposed pad for exactly this reason, and the pad has to be stitched to an inner copper plane rather than left on a thin surface trace.

The supply current figures look trivial until a product runs from a battery. With both channels on, the part draws 100 microamp typical and 120 microamp maximum, and with both off it draws 0.01 microamp typical and 1 microamp maximum. On a mains powered set top box that is noise. On a battery backed unit that keeps two peripheral rails available in standby, it is the difference between a two week shelf life and a two month one, and the 1 microamp maximum is the number to use in that calculation rather than the typical.

The undervoltage lockout is worth planning around on a 5 V rail that comes from a wall adapter. The lockout sits at 4.0 V typical, and below it the switches are held off and the fault flags go high impedance, which means a host that polls the flag during a brownout sees an open circuit rather than an asserted fault. Firmware that treats a high impedance flag as healthy will report a port as fine while it is actually disconnected. Pull the flag up to the host rail and treat a rail loss separately.

  • Current limit at the hot corner, not at 25 C, since the two windows differ by 0.6 A at the top and 0.2 A at the bottom.
  • On resistance on the assembled board at the rated current, measured as a voltage drop across the part rather than inferred from a data sheet row.
  • Fault flag behaviour during inrush, where the deglitch window decides whether the host sees one edge or a burst of them.
  • Junction temperature of the VSON body at maximum load in the enclosure, using the thermal resistance for the copper area actually present.
  • Behaviour during a 4.0 V brownout, where the switches are off and the flags float.
  • Output discharge at power down, since this part pulls the port down and a downstream device may see that as an active low signal.

Which projects this part fits

This part fits multi port USB hubs and charging boards, set top boxes and televisions that switch individual peripheral rails, industrial control cards with several isolated loads on one 5 V bus, test fixtures where each device under test needs its own current limited feed, and any product where two downstream loads have to be switched and monitored from one host pin pair. It is also the practical choice when a board already carries the single channel TPS20xxC parts and a second port has to be added without a second regulator, because the dual member shares the same body height and the same control logic.

Questions that come up before a purchase order is released

Can the two channels be paralleled for 4 A?

Not safely. Each channel limits at its own threshold, and two channels in parallel will not share current evenly, so one will sit in current limit while the other carries the load. The family is specified channel by channel and the document gives no paralleling guidance. A load above 2 A needs a single higher current switch or two separate ports.

What happens when the output is shorted before the channel is enabled?

The part limits the current as soon as it is enabled into the short, holds constant current mode, and the junction temperature climbs until thermal shutdown at 135 C takes over. Recovery is automatic after the die cools, which means a permanent short produces a repeating cycle rather than a permanent off state. Software has to count the fault events and disable the channel after a set number.

Is the fault flag edge or level?

It is a level output, open drain, active low, and it is deglitched so a short transient does not assert it. It clears on its own when the channel returns to normal current. On a multi port board the flags of several parts can be wired to one host input as a wired OR, with each part polled in turn to find the port that caused the event.

Does the part need an output capacitor?

A capacitor at each output keeps the transient current inside the switch and helps the constant current loop settle. The document shows 150 microfarad per port in its typical application, which is a large electrolytic or a bank of ceramics. Below that the inrush into a downstream bulk capacitor is drawn from the 5 V rail through the switch, and the rail droop is what the host sees.

What is checked at incoming inspection?

The reel label against the order, the moisture bag, marking on a sample, and a functional test that enables each channel into a known load and confirms the fault flag asserts at a current between the two published limits. The limit window is wide enough that a single point test proves little, so the test records the actual trip current for the lot.

How SUPERB handles this line

We supply the TPS2003CDRCR on original 3000 piece reels with lot and date code traceability, and we can ship a cut quantity for a prototype build against the same reel. The power management cross reference page lists the distribution switches and hot swap controllers we carry by position and rating, pin to pin cross reference covers the case where a board has to move from an older TPS20xx member to this family, and incoming inspection plan sets out the checks we run on a switch lot before it is kitted.