Contact Us

TPS1HC30BQPWPRQ1

Brand: Texas Instruments
Texas Instruments TPS1HC30BQPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS1HC30BQPWPRQ1 — Power Management & Signal Chain | Superb Automation

TPS1HC30BQPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS1HC30BQPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS1HC30BQPWPRQ1: automotive high side switch, 30 milliohm, 5 A, with current sense

TPS1HC30BQPWPRQ1 is a single channel automotive high side switch with a 30 milliohm FET and full diagnostics in a HTSSOP body of 14 pins. It switches a load from a 3 V to 28 V rail and reports the current through an analog sense output, with a programmable current limit that is accurate to 15 per cent at 3.5 A and a sense accuracy of 6 per cent at 1 A. The diagnostics cover open load in both states, short to battery, overload and thermal shutdown, which is what a body control module needs to tell a lamp from a short.

Order code and package

TPS1HC30BQPWPRQ1Active, HTSSOP-14 with thermal pad, 3000 pieces on a large reel, MSL-3-260C-168 HR
Marking1HC30Q
Standby current2.5 microamp at 85 degrees
Operating junctionminus 40 to 150 degrees
Logic compatibility1.8 V, 3.3 V and 5 V inputs, threshold 1.5 V

Electrical parameters that decide the application

Operating voltage3 V to 28 V
On resistance30 milliohm
Continuous current5 A
Current limit accuracyplus or minus 15 per cent at 3.5 A
Current sense accuracyplus or minus 6 per cent at 1 A
Standby current2.5 microamp at 85 degrees
Load dumprated for the clamped event, maximum 3 minutes with the 28 V rail
Protectionoverload, short circuit, inductive clamp, undervoltage lockout, thermal shutdown with self recovery

Family variants and how they differ

Status outputopen drain, reports a fault to the controller
Current sense outputanalog, follows the load current with the stated accuracy
Fault sense scalingthe sense voltage is scaled so an ADC input is not overdriven
Reverse batteryprotected, the switch survives a reversed supply
Loss of ground and loss of supplyboth handled, which is a body control module requirement

Points to check before this part goes on a BOM

The sense accuracy is quoted at 1 A and the limit accuracy at 3.5 A. Those are different jobs. The sense output tells the controller what the load is doing, and 6 per cent at 1 A is good enough to tell a 5 W lamp from a 21 W lamp. The limit protects the harness, and 15 per cent at 3.5 A is what allows a connector to be protected without derating the load by a third.

2.5 microamp of standby current is the figure for a parked vehicle. A body control module with a dozen of these switches has to keep the battery alive for weeks. At 2.5 microamp each the total is small enough to matter, and the number is quoted at 85 degrees, which is the realistic under bonnet ambient rather than room temperature.

Open load detection works in both states and they are not the same circuit. In the off state the switch looks for a pull up through the load, and in the on state it looks for current below a threshold. A lamp that is open will show a fault in one state and not the other, so the firmware has to test in the state where the diagnosis is valid.

Reverse battery protection is not the same as reverse current protection. The switch survives a reversed supply without damage, which is a test every automotive module has to pass. That is a different guarantee from blocking current that flows backwards from the load, and a load that can source current needs the second guarantee.

Thermal shutdown with self recovery suits a load that is allowed to resume. A lamp that is switched back on after cooling is a better outcome than a module that stays dark until the ignition cycles. The self recovery also means a shorted output produces a repeating cycle rather than a permanent off state, which is visible on the diagnostics and useful to a service technician.

The 14 pin HTSSOP is a thermal package first. 30 milliohm at 5 A is 0.75 W in the switch, and that has to leave through the pad. A board with a small pad under the part runs the junction far above the ambient, and at 150 degrees the current capability is already reduced by the protection.

The inductive clamp is what makes it usable on a relay or a motor. Switching an inductive load off produces a voltage spike that would otherwise exceed the switch rating. The integrated clamp absorbs it, so no external diode is needed on a small actuator, which removes a part and a failure mode.

The logic threshold of 1.5 V allows a 1.8 V microcontroller to drive the switch directly. That removes a level shifter from the module and removes the propagation delay it would add. On a module with a dozen channels that is a real saving in board space and in the number of parts under the hood.

The limit and the sense are specified at different currents. The sense output is 6 per cent at 1 A and the limit is 15 per cent at 3.5 A. A controller that infers the load current from the sense and compares it with the limit sees a gap at the top of the range, and a customer who expects the two to agree needs to be told they are separate specifications.

3 V to 28 V is the operating window, not the survival window. A 24 V truck system with a load dump goes well above 28 V, and the clamp in front of the switch is what brings the event inside. Four volts of headroom is enough for the rail and not enough for the transient without help.

The current sense scaling exists to protect the converter input. The sense voltage is scaled so a normal load does not overdrive the analog input of a 3.3 V or 5 V converter. A resistor divider added on top of the sense output changes the accuracy, so the scaling is part of the specification rather than a board level convenience.

The 14 pin body is a thermal package before it is a logic package. Most of the pin count is diagnostics and supply, and the pad is the reason the part can carry 5 A. A footprint that copies the pin positions but shrinks the pad gets the function and loses the current.

What a body control module asks of a high side switch

Distinguish an open lamp from a shorted harness without switching the load, which is what the two state open load detection provides.

Report the current rather than only a fault, so the controller can dim a lamp, detect a failing motor or count the energy delivered to a heater.

Where this order code fits

It switches and diagnoses automotive loads in body control, ADAS, display and HVAC modules, where the current has to be measured rather than guessed. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Defense Grade Components page.

Questions buyers ask

Can it drive a motor or a relay? Yes. The integrated inductive clamp handles the turn off spike, and the current limit protects the harness during a stall. The thermal behaviour under repeated stall is the thing to check on the bench.

What is the sense output used for? An analog voltage proportional to the load current, accurate to 6 per cent at 1 A. It lets the controller measure the load rather than only detect a fault, and the scaling keeps it inside a normal ADC input range.

Does it need an external diode? No for the inductive clamp, which is integrated. An external diode is only needed where the load can feed current back into the switch, which is a different condition from the turn off spike.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.