Contact Us

TMS5701114CZWTQQ1

Brand: Texas Instruments
Texas Instruments TMS5701114CZWTQQ1 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS5701114CZWTQQ1 — Power Management & Signal Chain | Superb Automation

TMS5701114CZWTQQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS5701114CZWTQQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS5701114CZWTQQ1: 180 MHz lockstep Cortex-R4F safety microcontroller, 337 ball BGA, C silicon revision

TMS5701114CZWTQQ1 is the C revision of the 180 MHz device in the 337 ball BGA, combining the full pin set with the current silicon in a BGA body of 337 pins. This code combines the 337 ball NFBGA body with the C revision of the LS1114: 1MB of ECC flash, 128K bytes of ECC RAM, 64K bytes of emulated EEPROM, two lockstep Cortex-R4F cores with an FPU at up to 180 MHz, seven ePWM modules, six capture modules, two encoder interfaces, two N2HET blocks and two 12 bit ADCs with 24 inputs. It is the part for a dense board that needs both the pin count and the current silicon.

Order code and package

Order codeTMS5701114CZWTQQ1
Coredual Cortex-R4F in lockstep, FPU, 180 MHz
PackageNFBGA, 337 balls, body code ZWT, 16 by 16 mm
Flash1MB with ECC
RAM128K bytes with ECC
Emulated EEPROM64K bytes
PWMseven ePWM modules
Timerstwo N2HET, 32 and 18 channels
ADCtwo MibADC, 24 inputs, 64 buffers each
Serialthree DCAN, three MibSPI, two SPI, LIN, SCI, I2C
Silicon revisionC
DatasheetSPNS188B, revised February 2015

Electrical parameters that decide the application

IdentificationJTAG ID and device identification code for revision C
Ball count337, full I/O set
Thermalheat path through the ball array into the board
DMA16 channels
Capture and encodersix eCAP, two eQEP
Interrupts128 channel vectored module
Self testCPU and RAM BIST
Error outputnERROR pin
ClockFMPLL with slip detector
InspectionX ray, no optical inspection possible
Moisturedry pack, bake before reflow if the seal is broken
GradeQ1 automotive, minus 40 to 125 C

Points to check before this part goes on a BOM

The combination of the 337 ball body and the current revision is what a production board needs when the board has already moved to the BGA footprint for pin count and the file has been qualified against the C errata list. Sourcing the B revision to match an older file is possible while stock lasts, but it is a spares strategy rather than a production one.

The revision can be confirmed in circuit through the identification codes, which matters on a BGA because the marking is small and a returned board cannot be inspected visually. That check is part of how we verify a lot before it goes onto a safety build.

Heat leaves this package through the balls, so the board carries the thermal load. At 125 C ambient with two cores at 180 MHz the junction is decided by the copper, the via count and the plane structure, and a BGA on a board with no thermal vias runs hotter than the same device in a leaded package.

Assembly cost is part of the price comparison. A 337 ball array needs a qualified reflow profile, X ray sampling and strict moisture control, and those are recurring costs on every lot. If the pin count is not needed, the 144 pin QFP version of the same device removes them.

The safety architecture is the same in both bodies: lockstep comparison, ECC on flash and RAM, parity on the peripheral memories, self test and the error signalling module with its external pin. The difference between a board that meets its diagnostic target and one that does not is usually whether those blocks are enabled and their outputs wired, not which package was ordered.

Two ADCs with 24 inputs and 64 result buffers each allow simultaneous sampling of two motor phases. With several power stages on one device, the trigger plan and the buffer indices have to be laid out before the firmware, because changing them later invalidates every timing measurement on the bench.

Stock of the earlier revision will thin out before the board is obsolete, so a spares plan should state whether the C revision can be used with the existing file. Where the workaround was only needed on the earlier silicon the answer is yes after an assessment; where the board relies on the older behaviour, the answer is to buy the remaining stock now and plan the change.

Traceability is the other half of buying this part. A 337 ball body with a Q1 marking and the C revision is a common target for relabelled stock, so lots are checked against the marking, the date code and the dry pack label, and the revision is read from the device identification before the lot goes to the line.

Where this order code fits

Traction and multi axis inverter boards where the pin count and the thermal path of the BGA are required, and production builds that have moved to the current silicon revision while the board stays on the 337 ball footprint. Boards comparing it with a neighbouring part start from our Supplier Quality Audit page, and boards replacing a part that has gone end of life start from the Incoming Inspection Plan page.

Questions buyers ask

Is this the same die as the QFP version? Yes, the C revision of the LS1114, in the 337 ball body. The package, the pin count and the thermal path change; the core, the memory and the peripheral set do not.

Can I confirm the revision on a finished board? Yes, through the JTAG and device identification codes that revision C provides. On a BGA that is the reliable way to check, since the marking is small and the joints cannot be seen.

Does the BGA version run cooler? It removes heat more effectively into the board, but only if the board provides the copper and the vias. The package alone does not lower the junction temperature; the thermal plan around it does.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the MCU Cross Reference page sets out the checks that keep a substitute from failing on the bench.