TMS5701114BPGEQQ1
Product Specifications
TMS5701114BPGEQQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS5701114BPGEQQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS5701114BPGEQQ1: 180 MHz lockstep Cortex-R4F safety microcontroller, 144 pin QFP, B silicon revision
TMS5701114BPGEQQ1 is the 180 MHz member of the TMS570 line in the 144 pin body: 1MB of ECC flash, 128K bytes of ECC RAM, two timer coprocessors and seven PWM modules for multi axis drive control in a LQFP body of 144 pins. The LS1114 runs the Cortex-R4F pair at up to 180 MHz with a single and double precision FPU, and keeps the full safety architecture: lockstep comparison, ECC on flash and RAM, parity on peripheral memories, built in self test for the CPU and the RAMs, an error signalling module with an external error pin, and voltage and clock monitoring. Memory is 1MB of program flash, 128K bytes of RAM and 64K bytes of emulated EEPROM. The PGE body is the 144 pin QFP and the B in the code is the silicon revision.
Order code and package
| Order code | TMS5701114BPGEQQ1 |
| Core | dual Cortex-R4F in lockstep, FPU, up to 180 MHz |
| Package | QFP, 144 pins, body code PGE |
| Flash | 1MB with ECC |
| RAM | 128K bytes with ECC |
| Emulated EEPROM | 64K bytes |
| PWM | seven ePWM modules, up to 14 outputs |
| Timers | two N2HET, 32 and 18 channels |
| ADC | two 12 bit MibADC modules, 24 inputs total |
| Serial | three DCAN, three MibSPI, two SPI, LIN, SCI, I2C |
| Supply | 1.14 to 1.32 V core, 3.0 to 3.6 V I/O |
| Datasheet | SPNS188B, revised February 2015 |
Electrical parameters that decide the application
| Silicon revision | B, marked in the order code |
| Performance | up to 300 DMIPS at 180 MHz |
| MPU | 12 region memory protection |
| DMA | 16 channels, 32 peripheral requests |
| Capture and encoder | six eCAP, two eQEP |
| ADC buffers | 64 result buffers per MibADC, parity protected |
| General purpose I/O | up to 64 pins |
| Interrupts | 128 channel vectored module |
| CRC | two channel checker |
| Clock | FMPLL with slip detector |
| Error output | nERROR pin from the error signalling module |
| Grade | Q1 automotive marking, minus 40 to 125 C |
Points to check before this part goes on a BOM
One megabyte of flash at 180 MHz is what a full drive application needs once the diagnostic library is linked in. The lockstep self test routines, the floating point library and the communication stacks together take a large share of the space, and the update image needs a second copy. The 144 pin body holds all of it without external memory, which removes a whole class of failure from the board.
The FPU changes how the control law is written. Field oriented control with an observer is floating point work, and single and double precision support means the fixed point scaling layer disappears. The timing budget then has to be measured on the new code rather than estimated from the old one, because a floating point loop has a different profile even when the maths is equivalent.
Revision B is the silicon the production file was likely written against. Errata workarounds are tied to the revision, so a lot that arrives on a C device may already fix an issue the firmware works around, and a workaround that depends on the bug can behave differently. We record the revision on the offer and keep B and C lots separate on the shelf.
Two ADCs with 24 inputs between them let a three phase drive sample two currents at the same instant. Map both phases onto one converter and the samples become sequential, which shows up as torque ripple at high modulation. The trigger sources and the buffer indices are part of the control timing, not a configuration detail.
The 144 pin QFP is easier to inspect than the ball grid array and easier to rework, which matters on a safety board where a reflowed joint has to be verified. The trade is pin count: the QFP exposes fewer general purpose pins than the 337 ball body, so a board that needs a wide parallel interface has to take the BGA.
The Q1 marking fixes the ambient range and the automotive qualification, but the 144 pin body still needs a thermal path. At 125 C ambient the junction depends on the copper area under the body and the via count, and on a 180 MHz part running two cores that calculation has to be done before the board is released.
Where this order code fits
Electric drive unit and inverter control, multi axis servo drives, active suspension and steering actuators, and industrial safety functions built to IEC 61508 where 1MB of flash holds the application, the diagnostic library and a field update image together. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Supplier Quality Audit page.
Questions buyers ask
Which body should a new build take, the QFP or the BGA? The QFP if the pin count fits and the board has to be inspectable and reworkable. The BGA exposes more pins in a 16 by 16 mm body, which is what a board needs when it drives several power stages and a wide interface at the same time.
Does the B revision limit performance? No, the clock and the memory are the same across revisions. The revision identifies which errata apply, and that is what the firmware workarounds are tied to, so it should be recorded with the lot.
Can this part replace the 160 MHz member of the family? The pinout and the peripheral set are compatible within the same body, and the 180 MHz device covers the 160 MHz specification. The firmware timing still has to be rechecked, because a faster core changes the loop period and any code that relies on cycle counts.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.