TMS5700914APGEQQ1
Product Specifications
TMS5700914APGEQQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS5700914APGEQQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS5700914APGEQQ1: 160 MHz lockstep Cortex-R4F safety microcontroller with 1MB of flash in the 144 pin body
TMS5700914APGEQQ1 is a 160 MHz dual core lockstep controller with a megabyte of flash, two timer coprocessors and seven PWM modules, for multi axis drive and inverter control with safety diagnostics in a LQFP body of 144 pins. The LS0914 moves the family up in clock and memory: 160 MHz Cortex-R4F pair with an FPU, 1MB of program flash with ECC, 128K bytes of ECC RAM, 64K bytes of emulated EEPROM, and the timing peripherals needed to run several power stages at once. Two N2HET modules provide 32 and 18 programmable channels, seven ePWM modules with up to fourteen outputs, six capture modules, two encoder interfaces, two 12 bit ADCs with 24 inputs and a 16 channel DMA. The PGE body is the 144 pin LQFP at 20 by 20 mm.
Order code and package
| Order code | TMS5700914APGEQQ1 |
| Core | dual Cortex-R4F in lockstep with FPU, up to 160 MHz |
| Package | LQFP, 144 pins, body code PGE, 20 by 20 mm |
| Flash | 1MB with ECC |
| RAM | 128K bytes with ECC |
| Emulated EEPROM | 64K bytes |
| PWM | seven ePWM modules, up to 14 outputs |
| Timers | two N2HET, 32 and 18 channels, 160 word instruction RAM each |
| ADC | two 12 bit modules, 24 inputs, 64 result buffers each |
| Serial | three DCAN, MibSPI, SPI, SCI with LIN, I2C |
| Supply | 1.14 to 1.32 V core, 3.0 to 3.6 V I/O |
| Temperature | minus 40 to 125 C, automotive grade |
| Datasheet | SPNS225D, revised November 2016 |
Electrical parameters that decide the application
| Performance | 265 DMIPS at 160 MHz, 1.66 DMIPS per MHz |
| FPU | single and double precision |
| MPU | 12 region memory protection |
| DMA | 16 channels, 32 peripheral requests, parity on the control packet RAM |
| Capture and encoder | six eCAP, two eQEP |
| General purpose I/O | up to 64 pins, 16 with interrupt capability |
| Interrupts | 128 channel vectored module |
| CRC | two channel checker |
| Self test | CPU and RAM BIST, ECC on flash and RAM, parity on peripheral RAMs |
| Error output | nERROR pin driven by the error signalling module |
| Clock | FMPLL with slip detector |
| Grade | Q1 automotive marking, A silicon revision |
Points to check before this part goes on a BOM
Seven ePWM modules with fourteen outputs plus two N2HET blocks is what allows one device to run several power stages without external logic. A three phase drive with a brake chopper and a power factor stage fits, and the timer coprocessors handle the encoders and the pulse trains that would otherwise need a second processor. The cost is that the timing plan has to be laid out before the firmware is written, because the modules share trigger and sync resources.
The FPU is the reason the 160 MHz part is chosen over the 80 MHz members for drive work. Field oriented control with a rotor position observer is floating point arithmetic, and a single precision unit with double precision support removes the scaling work that a fixed point implementation needs. It also changes the timing budget, so the loop has to be re-measured rather than scaled from the fixed point version.
The 64K bytes of emulated EEPROM and the 1MB of program flash are what make this part suitable for a drive that stores parameters, fault history and a field update image in one device. The program flash is 64 bits wide and runs in pipeline mode at 160 MHz, so code execution from flash keeps pace with the core.
The two ADCs have 24 inputs between them and sixty four result buffers each, and the buffers are parity protected. With two motors and a power stage, the trigger assignment decides whether the samples are simultaneous or sequential. Simultaneous sampling of the current in two phases has to come from two converters, and mapping both phases onto one converter adds a delay that shows up as torque ripple.
The 144 pin body at 20 by 20 mm is large enough that the thermal path is manageable, but at 125 C ambient the dissipation of two 160 MHz cores plus the I/O ring is not small. The thermal calculation belongs in the first board review, with the copper area, the via count and the airflow all decided then, because it cannot be fixed by changing a component later.
The Q1 marking and the A revision are both in the order code and both matter. The grade fixes the ambient range and the rev tells the firmware which errata apply. On a safety device the two have to match the production file, and we state both on the offer so the build does not mix revisions across a lot.
Where this order code fits
Multi axis servo and traction inverter control, electric vehicle drive units, grid tied converter control, and aerospace or railway actuation where a 160 MHz core with lockstep diagnostics and a large flash budget is needed in one device. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Supplier Quality Audit page.
Questions buyers ask
What does this part add over the 100 pin members of the family? Clock, memory and timing resources: 160 MHz instead of 80, 1MB of flash instead of 128K to 384K, seven ePWM modules, two N2HET blocks and two ADCs with 24 inputs. It is the part for multi axis or multi stage power control in one device.
Is the FPU usable in a safety function? Yes, with the self test and the ECC coverage in place and the floating point routines qualified like the rest of the code. The lockstep pair covers the FPU as well, so a fault that changes a floating point result is caught by the comparator.
How many encoder interfaces does it have? Two eQEP modules, plus the N2HET blocks which can implement additional position interfaces in their own instruction set. For a dual axis drive the two eQEP channels are the straightforward choice.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.