TMS5700432APZQQ1
Product Specifications
TMS5700432APZQQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS5700432APZQQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS5700432APZQQ1: lockstep Cortex-R4F safety microcontroller with 384K bytes of flash, 100 pin body
TMS5700432APZQQ1 is the largest flash option in the 100 pin TMS570 body: 384K bytes with ECC, the same lockstep pair and the same diagnostic set as the rest of the family in a LQFP body of 100 pins. The LS0432 carries 384K bytes of program flash with ECC in the same 100 pin LQFP as the 256K member, with 32K bytes of ECC RAM and 16K bytes of emulated EEPROM. The core is the familiar 80 MHz Cortex-R4F pair in lockstep, with built in self test, an error signalling module with an external error pin, voltage and clock monitoring, two CAN controllers, a 19 pin N2HET and a 16 channel 12 bit ADC with sixty four result buffers.
Order code and package
| Order code | TMS5700432APZQQ1 |
| Core | dual Cortex-R4F in lockstep, 80 MHz |
| Package | LQFP, 100 pins, body code PZ |
| Flash | 384K bytes with ECC |
| RAM | 32K bytes with ECC |
| Emulated EEPROM | 16K bytes |
| ADC | 12 bit, 16 channels, 64 result buffers |
| CAN | two DCAN controllers |
| N2HET | 19 programmable pins |
| Supply | 1.2 V core, 3.3 V I/O, 3.3 V ADC |
| Temperature | minus 40 to 125 C, automotive grade |
| Datasheet | SPNS186C, revised May 2018 |
Electrical parameters that decide the application
| Flash size | 384K bytes, the largest in the 100 pin body |
| Flash interface | 64 bit wide, pipeline mode at 80 MHz |
| RAM | 32K bytes, ECC protected |
| Self test | CPU and RAM BIST, runs at start up and on demand |
| Error pin | nERROR output toggled on a fault |
| Serial | two DCAN, MibSPI with 128 words, two SPI, SCI with LIN |
| Timers | N2HET with angle generator, HTU for data transfer |
| Encoder | eQEP module |
| Interrupts | 96 channel vectored module |
| CRC | two channel checker |
| MPU | 8 region protection |
| Grade | Q1 automotive marking |
Points to check before this part goes on a BOM
Three hundred and eighty four kilobytes is what makes a field update practical on a single device. The running application stays in one part of the flash while the new image is downloaded into the other, and the swap happens at the next reset. On the 256K member the same scheme works only if the application is small enough to keep two copies, which is often not the case once the diagnostic software is linked in.
Flash is 64 bits wide and runs in pipeline mode at 80 MHz, so instruction fetch keeps up with the core without wait states. That is a real advantage for a lockstep pair, because a wait state stalls both cores and the comparison logic together, and the loop timing that was measured with the code in RAM still holds with the code in flash.
The emulated EEPROM area is 16K bytes and it is separate from the program flash. Calibration and fault logs belong there, and the writes should be batched and rotated because the endurance is that of flash. A log written every second wears the block out long before the product life is over, and the failure appears as a calibration loss rather than as a flash error.
Two CAN controllers with parity protected mailboxes are the minimum for a body or chassis controller that has to stay on the network during diagnosis. A single controller shared between two buses through an external switch is not equivalent, and on a safety device it also removes the ability to keep one network alive while the other is being serviced.
The lockstep comparison only covers the core. The flash, the RAM, the buses and the peripherals are covered by ECC, parity and the self test routines, and each of those has to be enabled and its error output routed to the error signalling module. A board that enables the cores and forgets the RAM ECC has half the diagnostic coverage it paid for.
The Q1 marking is the automotive grade and the part is specified from minus 40 to 125 C, but the 100 pin body still needs a thermal path. At 125 C ambient the junction is above that by the thermal resistance times the dissipation of two cores and the I/O ring, so the copper under the body and the number of thermal vias are part of the specification, not a routing preference.
Where this order code fits
Motor and inverter control with several control loops in one device, battery management with a large calibration set, and automotive body controllers that need room for an update image next to the running application in the same flash. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Supplier Quality Audit page.
Questions buyers ask
Why pay for 384K bytes when 256K is available in the same body? Two reasons: a field update image that has to coexist with the running application, and a calibration or diagnostic set that grows after the first production release. Both are hard to add later without changing the part, and the pinout is the same either way.
Does the bigger flash change the current consumption? The core and I/O currents stay in the same range, and the flash program and erase current is a short pulse rather than a steady load. What changes is the time an erase takes, and that matters for the thermal budget on a hot board and for the length of a field update.
Can the part run from an external crystal only? It needs a clock source and the FMPLL multiplies it to 80 MHz, with a slip detector that flags a lost or drifting reference. A noisy oscillator shows up as a clock monitor fault rather than as corrupted arithmetic, which is the behaviour a safety device should have.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.