TMS470R1A288PGEA
Product Specifications
TMS470R1A288PGEA
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS470R1A288PGEA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS470R1A288PGEA: 288K byte ARM7TDMI flash microcontroller in the 144 pin body with the expansion bus
TMS470R1A288PGEA is the largest member of the TMS470R1A family: 288K bytes of flash in two banks, 16K bytes of SRAM, two CAN controllers and a 42 pin expansion bus on a 144 pin LQFP in a LQFP body of 144 pins. The PGE body is the only one in this family that brings out the expansion bus, and it is what separates a board that can hang external memory or a peripheral interface off the processor from one that cannot. Flash is 288K bytes in two banks of eight contiguous sectors, SRAM is 16K bytes in a single array, and the device carries two CAN controllers, three I2C modules, a twelve channel high end timer lite, a ten bit twelve channel ADC and a memory security module.
Order code and package
| Order code | TMS470R1A288PGEA |
| Core | ARM7TDMI, 16 and 32 bit, big endian |
| Clock | 24 MHz system clock, 48 MHz pipeline mode |
| Package | LQFP, 144 pins, body code PGE |
| Flash | 288K bytes, two banks of eight contiguous sectors |
| SRAM | 16K bytes, single array |
| CAN | two SCC controllers, 16 mailboxes each, protocol 2.0B |
| High end timer | HET lite, 12 channels, 12 high resolution |
| ADC | 10 bit, 12 channels, 64 word FIFO |
| Expansion bus | 42 pins, 8 and 16 bit, PGE body only |
| Core supply | 1.8 V nominal |
| Datasheet | SPNS106B, revised August 2006 |
Electrical parameters that decide the application
| Instruction cycle | one system clock, 24 MHz, 48 MHz in pipeline mode |
| Flash banks | two, allows code to run from one bank while the other is erased |
| Sector erase | per sector, eight sectors per bank |
| Flash endurance | 50 000 write and erase cycles at the rated temperature |
| General purpose I/O | 50 dedicated pins plus 43 shared on the PGE body |
| DMA | 16 channels, 32 control packets |
| I2C | three modules, multi master |
| Memory security | MSM, flash contents can be protected against readout |
| Watchdog | digital and analog, the analog one resets on a missed service |
| Clock module | zero pin PLL, multiply by 8 option |
| Low power | STANDBY and HALT |
| Temperature | grade letter at the end of the order code, confirm at order |
Points to check before this part goes on a BOM
The grade letter in this code sits in a field the family data sheet fills with two values: T for minus 40 to 105 C and Q for minus 40 to 125 C. An A in that position is not one of the two the nomenclature figure lists, so we take the grade off the TI packaging data for the exact code before an offer goes out. Quoting a temperature range from the code alone is how a board ends up specified twenty degrees wider than the part it receives.
Two banks of eight sectors is the feature that makes field updates safe. Code can execute from one bank while the other is erased and reprogrammed, so a gateway or a body controller can take an update over CAN without dropping its network for the length of an erase. Boards that store the whole application in one bank have to stop the network, and that is usually unacceptable on a vehicle bus.
The expansion bus is 42 pins that only exist on the PGE body. It supports 8 and 16 bit devices and it shares pins with the general purpose I/O, so a board that uses the bus loses most of its port pins. The 100 pin PZ body has no expansion bus at all, which makes the two bodies different boards rather than a footprint variant.
Two CAN controllers with sixteen mailboxes each is the reason this part is chosen over the A256. A gateway needs both networks live at the same time, and the second controller also allows one network to keep running while the other is being diagnosed. Sharing a single controller between two buses through an external transceiver switch is not the same thing and shows up as lost frames under load.
The memory security module protects the flash against readout. On a repair or a re-source, that means a locked part cannot be copied, and the replacement has to be programmed from the customer's binary. We ask for the binary and the security setting before quoting a programmed part, because a locked device that arrives without them is a dead end.
The ADC on this device has twelve channels, not sixteen, and they are shared with digital functions on the 144 pin body. A board that needs sixteen analogue inputs has to either move to a device with a larger converter or add an external multiplexer, and the multiplexer settling time then becomes part of the sampling budget inside the control loop.
Where this order code fits
Automotive body controllers and gateway modules that sit on two CAN networks, industrial gateways that need an external bus for a second memory or a bus interface, and instrument platforms where 288K bytes of code space removes the need to split the application across two devices. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
What temperature grade is this exact code? The family data sheet defines T as minus 40 to 105 C and Q as minus 40 to 125 C, and this code carries neither letter in that position. We confirm the grade from the TI packaging data for the code before quoting, and we state the confirmed range on the offer.
Can the two flash banks be used for a live update? Yes. Code executes from one bank while the other is erased and programmed, which is what allows an update over CAN without stopping the application. The loader and the vector table have to be arranged for it from the start, so it is a firmware decision, not a field retrofit.
Does the 100 pin version of this device have the expansion bus? No. The expansion bus with its 42 pins exists only on the 144 pin PGE body. The PZ body carries the same core and flash with a much smaller I/O count and no external memory interface.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.