TMS320VC5509AGHH
Product Specifications
TMS320VC5509AGHH
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320VC5509AGHH from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320VC5509AGHH: 200 MHz C55x DSP with USB in a 179-ball BGA
TMS320VC5509AGHH is a fixed point digital signal processor from the C55x generation in a NFBGA body of 179 pins. It runs at 200 MHz from a 1.6 V core with 3.3 V input and output, carries 128K words of on-chip RAM and includes a full speed USB slave port. The GHH order code is the 179-ball BGA, which brings out one more general purpose pin than the 144-pin package.
Order code and package
| Order code | TMS320VC5509AGHH |
| Package | 179-ball BGA, GHH body |
| Packing | tray |
| Core | C55x fixed point DSP at 200 MHz |
| Memory | 64K bytes of dual access RAM and 24 blocks of 4K by 16 single access RAM |
| Supply | 1.6 V core at 200 MHz, 3.3 V input and output |
| USB | full speed 12 Mbit/s slave port |
Electrical parameters that decide the application
| On-chip RAM | 32K words of dual access plus 96K words of single access |
| External bus | asynchronous memory interface for EPROM, SRAM and peripherals |
| Serial | multichannel buffered serial ports and a host port interface |
| USB | full speed slave, 12 Mbit/s, no on-chip transceiver in some configurations |
| I/O | eight general purpose pins on the BGA against seven on the LQFP |
| Clock | phase locked loop with an external crystal |
| Boot | ROM loaders for host, serial and external memory boot |
Family variants and how they differ
| AGHH | 179-ball BGA, the part on this page |
| APGE | 144-pin LQFP of the same device |
| VC5509 | the earlier member without the A suffix |
| VC5502 | a smaller memory member of the same core generation |
Points to check before this part goes on a BOM
The C55x core is a dual multiply accumulate machine with a variable length instruction set, and at 200 MHz it delivers roughly twice the throughput of a C54x at the same clock on filter code. The catch is that the C55x compiler and the hand written assembly of the C54x era are different worlds, so a port is a rewrite of the inner loops.
Memory is 32K words of dual access RAM plus 24 blocks of 4K by 16 single access RAM, which is 128K words in total. The block structure matters because the DMA can move data between blocks without stalling the core, and a buffer placed across a block boundary costs an extra cycle per access.
The USB port is a full speed slave, not a host, and not high speed. A product that needs to appear as a device to a PC can use it; a product that needs to read a memory stick cannot. The port also needs the external components the data sheet specifies, and a change in those components changes the eye diagram at the connector.
The BGA body brings out eight general purpose pins against seven on the LQFP, and it also changes the thermal path: the balls carry heat into the board, so the copper under the device is part of the thermal plan. A 179-ball 0.8 mm BGA needs x-ray inspection after reflow, which is a production cost the LQFP version does not carry.
Two rails again: 1.6 V for the core at 200 MHz and 3.3 V for the input and output rings, with a specified power up order. The core regulator is usually a small switching part, and its ripple lands on the analogue supplies if the filtering is not planned, which shows up as noise in the converter and in the audio path.
The external memory interface is asynchronous, so it can attach an EPROM or a slow SRAM without a controller. That is enough for a boot image and for data tables; it is not a high bandwidth path, and a product that needs to stream samples to external memory should measure the interface throughput rather than assume it scales with the core clock.
This generation is legacy. The devices are still listed, but the supply is allocation driven and the aftermarket is the practical source for repair quantities. A buyer should record the revision marking and the date code, because the C55x silicon revisions differ in the errata that affect the USB and the external bus timing.
A 179-ball package is not repairable on a bench without reballing equipment. Products that are still supported in the field should hold spare boards rather than spare devices, and the support plan should say so before the last of the boards is scrapped.
The BGA body carries heat into the board through the balls, so the copper under the device is the thermal path. A board that calculates junction temperature from the ambient and the package figure alone, without the copper, is calculating a number that does not describe the assembly and usually underestimates the rise.
The USB port is a full speed slave with the external components the data sheet specifies. Those components set the impedance and the edge rate at the connector, and a substitution that looks electrically equivalent can move the eye diagram outside the specification without failing a continuity test.
The external memory interface is asynchronous, so a boot EPROM can be attached directly. The loader in ROM reads the boot table over that interface with the wait states in the table itself, which means the memory speed has to match the table. A slower device boots into a fault that looks like a dead processor.
A 179-ball package needs reballing equipment to replace, so field support is by board swap rather than by device replacement. A product with a ten year service life should hold spare boards, and the support plan should say so before the last production run rather than after the spares run out.
The core voltage is generated by an external regulator on this generation, and its accuracy at the 1.6 V set point decides whether the device meets its timing. A regulator with a two percent tolerance at the low end puts the core under the specified minimum, and the failure appears as a device that works cold and fails hot.
The USB port needs a 48 MHz clock derived from the same crystal as the core, and the clock generation block has to be configured for both. A product that changes the core clock for power reasons without checking the USB divider loses the port, and the symptom is a device that enumerates on one board and not on another. The practical sourcing answer for a product on this generation is a last time buy against the remaining production plan plus a documented alternative, because the aftermarket supply carries revisions that were never part of the original qualification and a lot with no traceable marking is a risk in a product that is still supported in the field.
Where this order code fits
It is used in legacy audio and voice products, portable instrumentation and industrial boards that need a DSP with a USB device port. Teams comparing it with a neighbouring part start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
What is the difference from the PGE version? Package and one GPIO. The GHH is a 179-ball BGA with eight general purpose pins, the PGE is a 144-pin LQFP with seven.
Does the USB port work as a host? No. It is a full speed slave port at 12 Mbit/s, so it can present the product to a PC but cannot read a host device.
How much RAM is on chip? 128K words in total: 32K words of dual access RAM and 96K words of single access RAM in 24 blocks of 4K.
Can a C55x part replace a C54x board? Not directly. The instruction set and the peripherals differ, so the firmware has to be ported and the board rerouted.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.