Contact Us

TMS320VC5502PGF200

Brand: Texas Instruments
Texas Instruments TMS320VC5502PGF200 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS320VC5502PGF200 — Power Management & Signal Chain | Superb Automation

TMS320VC5502PGF200

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS320VC5502PGF200 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS320VC5502PGF200 two hundred megahertz fixed point signal processor in a 176 pin package

The TMS320VC5502PGF200 is a fixed point digital signal processor from the C55x generation, running at 200 MHz with a 5 ns instruction cycle. It carries 32K words of dual access RAM, 16K words of one wait state ROM and a 16 KB instruction cache, and it reaches 8M words of external memory through a 32 bit external memory interface. The package is a 176 pin low profile quad flat pack, and the code ends in 200 for the clock rate, with a 300 MHz sibling in the same body.

The device is aimed at audio, voice, instrumentation and control products that need a deterministic multiply accumulate engine rather than a general purpose core. Two arithmetic logic units and dual multipliers give up to 600 million multiply accumulates per second, and the peripheral set includes three multichannel buffered serial ports, an 8 or 16 bit host port, I2C, a UART and four timers. For a product that must stream samples in and out with fixed latency, this is the shape of part that does it without an operating system in the way.

Key parameters taken from the TMS320VC5502PGF200 document

CoreTMS320C55x fixed point, 200 MHz, 5 ns instruction cycle, up to 600 million multiply accumulates per second
Internal memory32K words of dual access RAM in eight blocks of 4K words, which is 64 KB
ROM16K words of one wait state on chip ROM, 32 KB
Cache16 KB instruction cache
External memory32 bit external memory interface, 8M words of addressable space, glueless to asynchronous static RAM and ROM
DMAsix channel controller
Serialthree multichannel buffered serial ports, a UART, an I2C interface
Host interface8 or 16 bit parallel host port
Timersfour timers including two 64 bit general purpose timers, a 64 bit watchdog and a DSP BIOS counter
Clockprogrammable analog phase locked loop
PackageLQFP PGF, 176 pins
Order code factsTMS320VC5502PGF200, tray of 40, MSL Level-4-260C-72HR, minus 40 to plus 85 C, Active, marking 320VC5502PGF

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The temperature range stops at plus 85 C, which is the industrial grade, not the extended range that some buyers assume for a DSP. A product in a sealed enclosure with a power stage nearby has to be checked against that limit, because a 200 MHz core plus external memory draws real current and the case temperature rises quickly. The 300 MHz sibling in the same body draws more and runs hotter, so the choice of clock rate is also a thermal decision.

The host port is the interface that makes this part easy to integrate. An 8 or 16 bit parallel port lets a host processor or a field programmable gate array load code and exchange data without touching the DSP core, which is how a two processor product keeps the signal chain deterministic. On a board where the host is an ARM application processor, the host port is often the only link that does not need a driver stack.

The 16 KB instruction cache matters more than the number suggests. C55x code that runs from external memory without a cache stalls on every instruction fetch, and the stated performance assumes the inner loops fit in the cache. A firmware team that measures throughput on a small test loop and then integrates a large application will find the number drops, and the fix is to place the hot functions in internal RAM rather than to raise the clock.

The moisture level is 4 with a 72 hour floor life, the same class as the larger controllers in this batch. The package is a 176 pin quad flat pack with a fine lead pitch, so the solder paste print and the reflow profile both matter, and a tray left open over a weekend has to be baked before it goes to the printer.

The order code carries the clock rate at the end, and the same body is offered at two rates. A board built for the 300 MHz part will run the 200 MHz part, but the firmware timing has to be rebuilt against the lower clock, and any delay loop written in cycles will be wrong. Where a product is being re-qualified, the clock rate should be treated as a configuration item, not as a purchasing detail.

  • The host port allows a two processor architecture where the host handles the user interface and the DSP handles the sample stream.
  • Three multichannel buffered serial ports cover several audio channels plus a control link without external glue.
  • The 32 bit external memory interface reaches 8M words, which is enough for a sample buffer that a small internal RAM cannot hold.
  • The programmable phase locked loop allows the core clock to be derived from a low frequency reference, which keeps the board clock tree simple.
  • The 85 C limit and the level 4 moisture class are the two handling constraints that belong in the process instruction, not only in the component file.

For the first article, measure the host port throughput with the DMA running, the serial port frame timing against the codec clock, and the core current at 200 MHz with all three serial ports active. Those three readings decide whether the product meets its sample budget and whether the enclosure can hold the part at 85 C. A bench measurement on an open board is not a substitute for the third one.

Which projects this part fits

Audio processing products, voice recorders, hearing instruments, industrial instrumentation, sonar and acoustic front ends, motor control with a deterministic loop and legacy telecom line cards are the natural applications. Many of these programs are long lived, which is why a 200 MHz C55x device is still bought today: the code base is qualified and the risk of a port is higher than the cost of the part. Our MCU cross reference lists what we hold against this family, and the obsolete part cross reference hub is where a replacement study starts when a long lived product needs a second source.

Questions that come up before a purchase order is released

Does this device have floating point hardware?

No. The C55x core is fixed point with dual multipliers, and floating point work is done in software. That is the main difference from the C674x devices, and it decides which algorithms can run in real time at this clock rate.

What is the difference between the 200 and the 300 suffix?

The core clock rate. Both codes share the 176 pin body, the memory map and the peripheral set, and the addendum lists both as in production. Firmware timing, the phase locked loop configuration and the thermal budget all change with the clock, so the rate has to be fixed before the board is released.

Can the device boot from the host port?

The boot mode is selected by the pins at reset, and the host port is one of the ways a host can load code. A product that uses this path needs the host to be alive before the DSP is released from reset, which changes the power up sequence and has to be reflected in the reset tree.

How SUPERB handles this line

We supply the TMS320VC5502PGF200 in original trays with date code and lot traceability, and we can hold a buffer for a long lived program that is still shipping. If the product is being ported to a newer device, send the sample rate, the channel count and the memory use and we will say plainly whether the port is worth doing. Start from the component shortage forecast page if the risk is supply rather than performance.