TMS320R2812ZHHA
Product Specifications
TMS320R2812ZHHA
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320R2812ZHHA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320R2812ZHHA: 179 ball lead free RAM based C28x DSP at 150 MHz
TMS320R2812ZHHA is the lead free version of the 179 ball flashless 2812, for boards that are assembled on a lead free line and cannot take the earlier ball finish in a BGA body of 179 pins. The ZHH body is the lead free 179 ball MicroStar BGA and the A option fixes the ambient range at minus 40 to 85 C. Everything else matches the GHH part: 150 MHz C28x core, 20K words of single access RAM, no program flash, the external memory interface on the R2812, sixteen PWM channels, a 12 bit 16 channel ADC, CAN, McBSP and two serial ports. The choice between GHH and ZHH is a solder and compliance decision.
Order code and package
| Order code | TMS320R2812ZHHA |
| Core | TMS320C28x, 150 MHz |
| Package | 179 ball MicroStar BGA, body code ZHH, lead free |
| RAM | 20K words single access |
| Flash | none |
| External bus | 16 bit, three chip selects |
| PWM | 16 compare channels |
| ADC | 12 bit, 16 channels |
| Core supply | 1.9 V at 150 MHz |
| I/O supply | 3.3 V |
| Temperature | minus 40 to 85 C, A option |
| Datasheet | SPRS257C, revised June 2006 |
Electrical parameters that decide the application
| Ball finish | lead free, Z body option in this family |
| Instruction cycle | 6.67 ns |
| Reflow | lead free profile, peak per the package qualification |
| Boot ROM | on chip, boot mode sampled at reset |
| Wait states | programmable on the external interface |
| Capture and encoder | six capture inputs, two encoder interfaces |
| Serial | SCI A, SCI B, SPI, McBSP, CAN |
| Digital I/O | 56 shared pins |
| Timers | three 32 bit CPU timers, four general purpose timers |
| PLL | on chip, ratio change at run time |
| Boundary scan | 1149.1 supported |
| Storage | moisture sensitive, bake before reflow if the seal is broken |
Points to check before this part goes on a BOM
The Z body exists so that one reflow profile covers the whole board. Mixing a leaded BGA with lead free paste is possible but it costs a second profile and a second inspection routine, and on a 179 ball array the joints cannot be inspected visually, so a mixed assembly is an X ray job for every unit. Choosing the ZHH code removes that cost.
Lead free assemblies run hotter in reflow, and the processor is not the only part that sees it. The moisture sensitivity level of the package decides whether a reel that has been open for a week needs a bake, and on a 0.8 mm pitch BGA the failure from a skipped bake is a delamination that only shows up after thermal cycling.
There is no flash on this die, so the program is loaded at power up. On a lead free contract build the loader belongs to the test fixture, which means the customer has to own the binary for the fixture as well as the application, and the fixture has to be available for every production run and every repair.
The external interface is what separates the R2812 from the R2811. With no flash and no external bus, an R2811 has nowhere to fetch code from except the boot ROM path, so the 128 pin PBK body is a different board, not a cheaper version of this one. Confirm the suffix on the BOM line before comparing offers.
Twenty thousand words of RAM is the budget. On a lead free build the temptation is to add logging and diagnostics during qualification and leave it in, which pushes the working set over the internal RAM and onto the bus. Every access that moves to the bus costs wait states inside the control loop, and the loop timing that was measured on the bench no longer holds.
The 85 C A grade is the right choice for indoor card cages, not for cabinets. If the board is sealed and has no fan, the ambient inside the enclosure is what the part sees, and a 60 C room becomes a 90 C board. The same die is available as the S grade to 125 C in the GHH body, which is the code to use when the thermal calculation is tight.
The A grade suits a card cage, not a sealed box, and the ball array makes that decision expensive to revisit. A 179 ball body is reworked only with hot air and a stencil, so a board that turns out to run at 95 C inside its enclosure needs a new processor and a new reflow rather than a socket swap. Measure the enclosure at full load before the first lot is built.
Where this order code fits
Contract builds that run a single lead free reflow profile across the whole board, products sold into markets that restrict lead in the finished assembly, and backplane or card based systems that load their code at power up and therefore never need flash on the processor. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Is the ZHH body the same part as the GHH with a different finish? Yes. Same die, same 179 ball map, same peripherals, and the difference is the lead free package option. The assembly profile and the storage handling change, the firmware and the board do not.
Does a lead free BGA need a different footprint? No, the ball map and the pitch are the same. What changes is the paste, the reflow profile and the inspection plan, and the moisture handling before reflow.
Can I mix this with a leaded BGA on the same board? It can be done, but the profile has to satisfy both parts and the joints cannot be inspected without X ray. On a 179 ball array the practical answer is to make the whole board lead free or the whole board leaded.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.