Contact Us

TMS320LF2406APZS

Brand: Texas Instruments
Texas Instruments TMS320LF2406APZS is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS320LF2406APZS — Power Management & Signal Chain | Superb Automation

TMS320LF2406APZS

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS320LF2406APZS from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS320LF2406APZS: 3.3 V fixed point DSP controller in a 100 pin LQFP body screened to 125 C

TMS320LF2406APZS is a 40 MHz C2xx core that closes a three phase motor loop on a 25 ns instruction cycle, with the PWM, ADC and CAN blocks of the 240xA generation on the same die in a LQFP body of 100 pins. The PZ body carries 100 pins and leaves out the external memory interface, so the 32K words of on chip flash and the 2K words of single access RAM are the whole memory system on the board. Flash is split into four sectors of 4K, 12K, 12K and 4K words, which lets a boot loader sit in a sector of its own while the application is erased in the field. The S at the end of the order code is the extended temperature option defined on the first page of SPRS145L: minus 40 to 125 C, against minus 40 to 85 C for the A option on the same die.

Order code and package

Order codeTMS320LF2406APZS
CoreTMS320C2xx fixed point DSP, code compatible with the F243 and F241
PackageLQFP, 100 pins, body code PZ
Flash32K words x 16 bits, four sectors of 4K, 12K, 12K and 4K
RAM2K words single access plus 544 words dual access
PWM12 compare channels across event managers EVA and EVB
ADC10 bit, 16 multiplexed inputs, twin autosequencer
SerialCAN, SCI and SPI
Supply3.3 V single rail, 3.0 to 3.6 V
Temperatureminus 40 to 125 C, S option
Boot ROMyes, SCI and SPI loader present
DatasheetSPRS145L, revised September 2007

Electrical parameters that decide the application

Instruction cycle25 ns at 40 MHz, 40 MIPS
Flash sectorsfour, individually erasable, 4K plus 12K plus 12K plus 4K words
ADC conversion500 ns minimum per channel in the features table, 16 conversions per autosequenced session
ADC inputs16 channels, 8 available on the smaller 240xA bodies
General purpose timersfour 16 bit timers, two per event manager
Capture inputssix, shared with two quadrature encoder interfaces
Deadbandprogrammable, prevents shoot through in a half bridge
PDPINTtwo power drive protection inputs that force the PWM pins high impedance
Digital I/O41 shared pins
External busnone on this body, the interface exists only on the LF2407A
Code securityflash readout can be locked, a locked part returns no code
JTAG1149.1 scan chain without boundary scan support

Points to check before this part goes on a BOM

The S grade is the reason to buy this exact code. The die is the same one used in the A grade at minus 40 to 85 C, so a board that was qualified on the A part and then moved to a cabinet that runs at 105 C keeps its firmware and changes only the order code, provided the flash timing is rechecked at the higher temperature and the ADC is recalibrated.

Leaving out the external memory interface is the other half of the story. On the 144 pin LF2407A the 64K program, 64K data and 64K I/O spaces are visible on the pins; on this 100 pin body they are not, so any code that was linked against external RAM or an external boot device has to be relinked into the 32K words of flash.

The four flash sectors are not equal. A 12K sector is the natural home for the application, the two 4K sectors suit a loader and a parameter block, and the erase granularity is a sector, not a word. Firmware that writes calibration data during a run has to keep that data in a sector it is prepared to erase whole, or move it to the 544 words of dual access RAM with a battery or an external EEPROM behind it.

Code security locks the flash against readout. On the repair bench that means a locked processor cannot be copied to a replacement, so a board that arrives with a dead 2406A and a locked flash needs the original firmware binary from the customer or a reflash from the production file. We ask for that file before we quote a programmed part.

Twelve PWM channels instead of sixteen is the visible cut against the 144 pin device, and both event managers are still present. A three phase inverter with complementary pairs uses six channels; the remaining six cover a second axis, a power factor stage or a chopper. Boards that need four independent three phase groups have to move to the 144 pin part.

The ADC is a 10 bit converter with 16 channels behind a twin autosequencer, and the two sequencers can be triggered by the event managers so that current sampling lands at a fixed point in the PWM period. The 500 ns figure is a minimum conversion time, so a full 16 channel sweep at that rate takes about 8 microseconds, which is the number to compare against the switching period before adding a second ADC or reducing the channel count.

Where this order code fits

This order code belongs on boards that run a motor or a power stage from a single 3.3 V rail and have no room for an external bus: pump and fan drives, appliance inverter control, brushless DC compressor boards, uninterruptible supplies and solar charge controllers. It also fits instrument front ends that need a fast ADC with an autosequencer and a CAN port, where the 100 pin body keeps the board small. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Is this a drop in replacement for the TMS320LF2407A? No. The 2406A is a 100 pin body and the 2407A is a 144 pin body, and the external memory interface and four PWM channels exist only on the 2407A. The instruction set and the peripherals are the same generation, so the firmware port is short, but the board has to change.

What does the S in the order code buy over the A? Forty degrees of ambient range. The S option is specified from minus 40 to 125 C and the A option from minus 40 to 85 C. The flash, the PLL and the ADC all need to be rechecked at the top of the range, and the ADC offset drifts, so the calibration routine has to run at the working temperature.

Can a locked part be read out on the bench? No. Once the code security option is set the flash cannot be read through JTAG or any other port. A replacement has to be programmed from the customer's binary or from the production file, and we need that file before the part can be quoted as programmed.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.