Contact Us

TMS320F2812PGFA

Brand: Texas Instruments
Texas Instruments TMS320F2812PGFA is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS320F2812PGFA — Power Management & Signal Chain | Superb Automation

TMS320F2812PGFA

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS320F2812PGFA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS320F2812PGFA: 150 MHz C2000 with an external memory interface in a 176-pin LQFP

TMS320F2812PGFA is a 32-bit fixed point control microcontroller with an external parallel bus in a LQFP body of 176 pins. It is the F2812: the member of the F281x family that carries the external interface unit, so it can map SRAM, a display controller or a FPGA into its address space. The PGFA order code is the 176-pin LQFP in the A grade at minus 40 to plus 85 degrees.

Order code and package

Order codeTMS320F2812PGFA
Package176-pin LQFP, PGF body
Packingtray
Core32-bit C28x at 150 MHz, 6.67 ns instruction cycle
Memory128K by 16 flash, 18K by 16 SARAM
External busXINTF present on this device number, absent on the F2811
Temperatureminus 40 to plus 85 degrees Celsius on the A grade

Electrical parameters that decide the application

ADC12-bit, 16 channels, two sample and hold circuits
Event managersEVA and EVB, 16 compare channels in total
SerialSCI A and B, SPI, McBSP, one CAN controller
External interfaceasynchronous SRAM, and synchronous memories with wait states
GPIO56 shared pins on 176-pin body
Supply3.3 V input and output, 1.8 V core
Interruptsthree external interrupts plus the peripheral set

Family variants and how they differ

F281064K flash and no external bus, 128-pin body
F2811128K flash and no external bus, 128-pin body
F2812128K flash with the external bus, 176-pin body, the part on this page
BGA bodies179-ball GHH and ZHH versions of the same device

Points to check before this part goes on a BOM

The external interface is the whole reason to choose this device number over the F2811. It gives a 16-bit data bus and a 19-bit address space with programmable wait states, so a product can put an asynchronous SRAM, a logic analyser port or a small FPGA beside the controller without a second processor or a serial bridge.

That bus is also the reason the 176-pin body exists. Fifty-six of the pins are shared between the interface and general purpose I/O, so a product that uses the external bus has fewer pins left for peripherals. Planning the pin map before the first board is cheaper than discovering when the board is routed that the bus and the PWM outputs want the same pins.

The A grade stops at 85 degrees ambient. In a cabinet with no airflow that is often enough, but the junction rise over this package at 150 MHz is not negligible, and the same device number in the S grade covers 125 degrees. The grade is a separate order code (PGFA against PGFS) and a separate line item, not a note on the drawing.

The family runs from two rails: 1.8 V for the core and 3.3 V for the input and output rings, with a specified power up order. A product that brings the rails up at the same time from a single sequencing supply is usually fine, but a reset circuit that releases the device before the core rail is valid can leave it in an undefined state that only a power cycle clears.

Flash here is 128K of 16-bit words, half of what the F28335 offers. A product that needs a field bus stack, a motion library and a bootloader can exceed that, and the external bus is then used to hold data rather than code, because code cannot execute from the asynchronous interface at full speed.

The eCAN module in this generation is the older controller, and the register set differs from the D_CAN instance in later C2000 parts. Firmware that is shared across two C2000 generations needs the CAN layer behind an interface, otherwise a port between them turns into a rewrite of the communication stack.

This generation has been in production since the early 2000s and it is bought now mostly for repair and legacy builds. A buyer should record the exact order code with its grade, because the same device number in another grade or another body is a different line item, often with a different lead time and a different qualified configuration for the product.

The package finish field in the addendum is worth reading before a RoHS statement is written. Some long lived order codes are offered with a leaded finish as well as a lead free one, and the finish is a separate attribute from the temperature grade and the packing, so it has to be stated on the purchase order rather than assumed from the device number.

The external interface adds wait states, and the number of states is set per bank in a register. An asynchronous SRAM with a 70 ns access time needs a different setting from a 10 ns part, and the setting has to come from the memory data sheet rather than from a copied example. Too few states gives intermittent read errors that move with temperature.

A parallel bus on a 176-pin package means many traces leaving the device, and those traces are the part of the board most likely to radiate. Series resistors on the address and data lines, and a ground return beside each group, are the usual mitigation; adding them after an EMC test failure costs a board spin.

The device is a 1.8 V core with 3.3 V input and output, and the interface pins swing at 3.3 V. A 5 V peripheral on the bus needs level translation, and a level translator with a slow enable can hold the bus in a state the controller reads as a stuck bit at reset.

For a repair programme the practical risk is the older revision. The device has been in production since the early 2000s, the errata differ between revisions, and a lot with no traceable marking cannot be assumed to match the revision the product was validated on. Boards that are still supported should hold spares from a known lot.

The 176-pin body brings out the full external interface and the full analogue set, which is why it is the body that legacy products were built around. A conversion to a smaller package is possible only if the external bus is no longer needed, and that is usually a firmware and product change rather than a board change. Boards built around this device are still in service in drives and instrumentation, so the practical sourcing question is not whether the part is listed but whether the lot on offer carries a date code and a revision marking that match the product's qualification record.

Where this order code fits

It is used in legacy drives, inverters and instrumentation that need a parallel bus for memory or a peripheral device beside the control loop. Teams comparing it with a neighbouring part start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Does the F2812 have external memory? Yes. XINTF provides a parallel interface with programmable wait states. The F2811 and F2810 in the same family do not have it.

What is the difference between PGFA and PGFS? Temperature grade. PGFA is the A grade at minus 40 to plus 85 degrees, PGFS is the S grade at minus 40 to plus 125 degrees, both in the 176-pin LQFP.

Can code execute from external SRAM? It can, but not at full speed. The interface has wait states and the C28x pipeline stalls on them, so time critical loops belong in the internal SARAM or flash.

Is the part still in production? It is listed as active in the current package addendum. Supply still comes from allocation, so a support plan for an existing product should include a last time buy quantity.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Last-Time-Buy and LTB Planning page sets out the checks that keep a substitute from failing on the bench.