TMS320F2811PBKS
Product Specifications
TMS320F2811PBKS
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320F2811PBKS from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320F2811PBKS: the 125 degree grade of the F2811 in the same 128-pin LQFP
TMS320F2811PBKS is a 32-bit fixed point control microcontroller in the extended temperature grade in a LQFP body of 128 pins. It is the same F2811 silicon as the A grade part and differs in one field: the S suffix covers minus 40 to plus 125 degrees ambient instead of 85. The PBKS order code is the 128-pin LQFP, tray packed, and it is the version specified for products that sit in a hot enclosure.
Order code and package
| Order code | TMS320F2811PBKS |
| Package | 128-pin LQFP, PBK body |
| Packing | tray |
| Core | 32-bit C28x at 150 MHz, 6.67 ns instruction cycle |
| Memory | 128K by 16 flash, 18K by 16 SARAM |
| Temperature | minus 40 to plus 125 degrees Celsius on the S grade |
| Difference from PBKA | temperature grade only, same silicon and same pinout |
Electrical parameters that decide the application
| ADC | 12-bit, 16 channels, 80 ns conversion at 25 MHz ADC clock |
| Event managers | EVA and EVB, 16 compare channels |
| Serial | SCI A and B, SPI, McBSP, one CAN |
| GPIO | 56 shared pins |
| Supply | 3.3 V input and output, 1.8 V core |
| Flash endurance | per sector figure in the family data sheet |
| Package thermal | 128-pin LQFP, junction to ambient set by the board copper |
Family variants and how they differ
| PBKA | A grade, minus 40 to plus 85 degrees |
| PBKS | S grade, minus 40 to plus 125 degrees, the part on this page |
| PBKQ | Q grade for automotive qualification where listed |
| GHH and ZHH | 179-ball BGA bodies of the same family |
Points to check before this part goes on a BOM
The S grade buys 40 degrees of ambient headroom over the A grade for a price step that is usually a small percentage of the device cost. In a sealed enclosure with a 60 degree internal ambient and a junction rise of 50 degrees per watt, the difference between an 85 degree and a 125 degree part is the difference between a product that passes its thermal test and one that does not.
Temperature grade does not change the electrical specifications at 25 degrees. It changes the range over which they are guaranteed. A board that works with the A grade part will work with the S grade part; the reverse is the case that fails, and it usually fails only in the field after a summer.
At 125 degrees ambient the internal 1.8 V regulator and the flash both see derated margins. Flash programming and erase over 125 degrees is restricted in the family data sheet, so a product that writes calibration data at run time has to check the junction temperature before the write rather than assume the grade covers it.
The 128-pin LQFP has a 0.5 mm lead pitch and no exposed pad, so heat leaves through the leads into the board. A socket or an adapter board under the device adds thermal resistance that the data sheet figure does not include, which is why a device tested in a socket can pass and the same device soldered can run cooler or hotter depending on the copper.
Because the A and S grades are the same silicon, a mis-marked or re-marked part is hard to detect electrically at room temperature. The reel label, the date code and the supplier trace matter more here than for a part where the grades differ in function, and a lot without traceable labelling should be treated as suspect for a 125 degree product.
The F2811 line has no external memory bus, so a 125 degree product cannot add SRAM or a display controller to the same device. If the application needs that, the F2812 in the 176-pin body is the alternative, and the board changes accordingly. Choosing the grade and the device number together avoids a respin later.
The ADC reference is internal and its accuracy over the extended range is what limits a measurement at 125 degrees, not the converter resolution. A 12-bit converter with a reference that drifts by tens of ppm per degree loses effective bits at the top of the range, so a product that needs accuracy at high temperature should use an external reference with a published curve.
For a repair or legacy build the two grades are ordered as separate line items with separate lead times, and substituting one for the other on a purchase order is a change to the product's qualified configuration. That is the kind of change an auditor asks about, so it should be recorded rather than absorbed.
At 150 MHz the flash needs wait states, and the family provides a pipeline mode that hides part of the access time. Code that runs from flash at the start of a control loop sees a different timing than the same code copied into SARAM, so a loop that is close to its deadline should be measured in both places rather than assumed.
The converter has a calibration routine in ROM that has to be run once after reset for the specified accuracy. A product that skips it works, and reads with an offset that varies from device to device. The routine is a few dozen cycles and belongs in the start up code, not in a service procedure.
This device number has no external memory interface, so every byte of code and data lives on chip. For a 125 degree product that is often an advantage: no external bus means no long traces carrying fast signals through a hot enclosure, and no second memory device to qualify over the same temperature range.
The 128-pin LQFP shares 56 pins between peripherals and general purpose I/O. A product that needs three PWM pairs, an encoder, two serial ports and the converter inputs will find that some combination is unavailable on this body, and the pin multiplexing table decides that before the board is routed rather than after.
The extended grade changes the storage and handling requirements as well as the electrical range. A 125 degree part that is stored or transported above its rated range and then soldered can carry moisture induced damage that a functional test at room temperature does not reveal, so the floor life and the bake rules in the addendum apply to it as much as to any plastic package. A functional test at room temperature does not prove a 125 degree part, and a soak at the top of the range with the product running its worst case load is the only check that exercises the derated margins in the regulator, the flash and the converter at once.
Where this order code fits
It is used in downhole tools, engine controllers, outdoor cabinets and other products that see a high ambient with no active cooling. Teams comparing it with a neighbouring part start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
Are PBKA and PBKS interchangeable? Electrically yes at room temperature; in a qualified product no. The S grade is the wider temperature part and the A grade cannot be used where the ambient exceeds 85 degrees.
Does the higher grade change the clock rate? No. Both run at 150 MHz. The grade changes the ambient range over which the timing and the electrical limits are guaranteed.
Can the flash be programmed at 125 degrees? The family data sheet restricts programming and erase at the top of the range. A product that stores data at run time has to check the junction temperature before writing.
Is there a BGA version? Yes, the family lists 179-ball GHH and ZHH bodies. The pin count and the peripherals differ from the 128-pin LQFP, so the board cannot be converted without changing the board.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Last-Time-Buy and LTB Planning page sets out the checks that keep a substitute from failing on the bench.