TMS320C6746EZWTA3
Product Specifications
TMS320C6746EZWTA3
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320C6746EZWTA3 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320C6746EZWTA3: an order code that has to be read carefully
The TMS320C6746EZWTA3 is a C674x processor in the 361 ball ZWT package, and the suffix carries a letter that changes what the part is against its neighbours in the same family. Reading that suffix correctly is the difference between a board that runs and a board that is reworked, because package, speed grade and temperature rating all move together in this part numbering scheme.
The silicon itself is the fixed and floating point C674x core, with 32 kilobytes of level 1 program cache, 32 kilobytes of level 1 data cache and 256 kilobytes of level 2 memory that can be split between cache and RAM. The peripheral set covers two external memory interfaces, a universal parallel port, a multichannel audio serial port, USB 2.0 high speed, Ethernet MAC, enhanced capture, enhanced PWM and a programmable real time unit subsystem.
Where a programme is buying this part today, the question is usually not performance. It is whether the order code will still be orderable in three years, and what the substitute looks like if it is not.
Key data for the TMS320C6746EZWTA3
| Core | C674x fixed and floating point, VLIW |
| Speed grades | 375 MHz at a 1.2 V core, 456 MHz at 1.3 V |
| Level 1 memory | 32 kilobytes program cache, 32 kilobytes data cache |
| Level 2 memory | 256 kilobytes, cache or mapped RAM |
| External memory | DDR2 and mobile DDR, plus NOR, NAND and SRAM |
| Audio | Multichannel audio serial port with sixteen serializers |
| Networking | Ethernet MAC, IEEE 802.3 |
| USB | USB 2.0 high speed with integrated PHY |
| Package | 361 ball NFBGA, ZWT, 16.00 mm by 16.00 mm |
| Finish | Nickel palladium gold, JEDEC level 3 at 260 C |
| Packing | Tray |
| Temperature | Set by the order code, 0 to 90 C on the ZWT grade |
Reading a C6746 order code before a substitute is quoted
Four things sit in the suffix: the package code, the speed grade, the temperature rating and a revision letter. A quotation that matches only the first two is not a match. Two parts can share the package and the ballout and differ in the temperature rating, which changes what the board can be sold as.
The safest procedure is to take the order code from the customer bill of material, look it up in the device comparison and ordering table, and write down the four items. Where a part is being bought as a replacement, the same table is what a supplier should be asked to confirm against, in writing, before samples are sent.
Revision letters are the quiet one. A revision can change an errata item, an analogue characteristic or a boot behaviour, and a product that was validated on an earlier revision may behave differently on a later one. For a long lived board, the revision should be recorded with the build, not just the part number.
What a package change does to a board that already exists
The ZWT and ZCE packages are both 361 ball NFBGA at 16 mm square, and they are not the same footprint. The ball map and the thermal pad arrangement differ, so a board made for one cannot take the other without a respin. Two suppliers quoting the same function in different packages are quoting two different boards.
Within one package, the differences are thermal and electrical rather than mechanical: the number of ground balls, the thermal path and the return path for the DDR2 interface. A board that was qualified for the higher speed grade in one package does not automatically meet the same timing in the other.
For a programme that is refreshing an existing board, the sensible step is to keep the package and change only the speed grade or the temperature rating if the supply needs it. That keeps the board, the test fixture and the qualification evidence intact.
Where it fits in a build
Audio and acoustic instruments, radar and sonar control, industrial imaging and legacy boards that are being kept alive. In each case the processor is a known quantity and the work is in keeping the supply and the documentation current.
That work is a comparison exercise, not a search for a better part. The obsolete part cross reference hub page sets out how we line up a candidate against the original on package, grade, boot path and errata, and the how to verify a drop in replacement page covers the tests that have to pass before a substitution is released to a line.
The sourcing side of this part is covered on the supplier onboarding checklist. For a processor bought as a replacement for an older order code, that page covers what is confirmed before the part is accepted.
Questions we get on this code
Is this part still in production? The family is mature and the ordering table lists active order codes, but the tray and reel options change over time. Confirm the specific code rather than the family name before a purchase order is raised.
Can a 375 MHz part be replaced by a 456 MHz one? Electrically only if the supply provides 1.3 V, and thermally only if the board can carry the extra dissipation. The pinout is the same within the package, so the change is a supply and a validation exercise.
What is the difference between the A suffix and the plain code? It marks a revision of the device, and the errata list is the document that says what changed. For a product already in the field, the revision should be part of the build record.
How should these be stored? In the tray, in a dry pack, at JEDEC level 3 the floor life is limited once the seal is broken. A board that is built months after the pack is opened needs a bake, and the bake is a process step that has to be in the build instruction.