TMS320C5505AZCHA12
Product Specifications
TMS320C5505AZCHA12
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320C5505AZCHA12 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320C5505AZCHA12: a fixed point DSP that keeps the analog close
The TMS320C5505AZCHA12 is a fixed point digital signal processor running at 120 MHz, with 256 kilobytes of single access RAM and 128 kilobytes of zero wait state ROM on chip. It is built for products that have to process audio or sensor data and also run a display and a user interface, which is why it carries an LCD bridge, a USB 2.0 high speed device port and a set of serial ports in the same 196 ball package.
The part is a 16 bit machine with 32 kilowatts of address space per instruction, and it executes one or two instructions per cycle. At 120 MHz that is 240 million instructions per second at the top of the range, which for a fixed point audio path is enough to run a filter chain, a codec and a small control loop at the same time.
The peripherals are the reason to choose this part over a smaller DSP. Four I2S ports for audio, an SPI with four chip selects, I2C, UART, MMC and SD, a 10 bit successive approximation converter with four inputs, and a real time clock that runs from a separate supply. An external memory interface handles 16 bit SDRAM, mobile SDRAM, NOR and NAND flash.
Key data for the TMS320C5505AZCHA12
| Core | Fixed point C55x, one or two instructions per cycle |
| Clock | 120 MHz on this order code, 60 to 150 MHz across the family |
| On chip RAM | 256 kilobytes of single access RAM |
| On chip ROM | 128 kilobytes, zero wait state, with a boot loader |
| Core supply | 1.3 V for 100 and 120 MHz parts, 1.05 V for 60 and 75 MHz parts |
| External memory | 16 bit SDRAM and mobile SDRAM, NOR, NAND, SPI EEPROM |
| Audio | Four I2S ports |
| Serial | SPI with four chip selects, I2C, UART, MMC and SD |
| USB | USB 2.0 full speed and high speed device port |
| Analog | 10 bit SAR converter, four inputs, fed from an internal 1.3 V regulator |
| Display | LCD bridge with an asynchronous interface |
| Package | 196 ball plastic BGA, lead free |
| Temperature | Minus 40 to 85 C industrial, at or below 120 MHz |
The internal regulator, and the place it stops working
The part includes a regulator that produces 1.3 V for the PLL and the analog supply of the converter. That removes a rail from the board and a sequencing problem from the start up, which is worth a lot on a product with a small power budget.
The limit is stated in the data sheet: the internal regulator only produces 1.3 V. When the PLL is asked to run above 120 MHz it needs 1.4 V, and beyond that point an external supply has to provide it. A board that copies a 150 MHz reference and runs at 120 MHz is fine; one that expects 150 MHz from the internal regulator is not.
The 120 MHz order code sits exactly at that boundary, so the internal regulator is usable and no external 1.4 V rail is needed. That saves a converter, an inductor and a sequencing dependency, and it is the reason this speed grade is common in products that are cost sensitive.
Audio, display and control on one device
Four I2S ports allow a codec, a Bluetooth audio device and a second codec to be connected at once, with a separate word clock domain for each if needed. The DSP moves samples between them with DMA, and the CPU spends its time on the filter chain rather than on moving bytes.
The LCD bridge drives a display without an external controller for simple panels. On a product like a portable instrument or a medical monitor, that removes a part and a bus, and it keeps the display refresh out of the audio interrupt path, which is where a small CPU usually loses its timing.
The 10 bit converter with four inputs is for slow signals: a battery voltage, a thermistor, a potentiometer, a reference. It is not a measurement converter, and a product that needs better than a few millivolts has to add one on the SPI bus.
Where it fits in a build
Portable audio, voice products, medical instruments with a display, industrial handhelds and test equipment. The part also turns up in legacy products where a C55x code base exists and the hardware is being refreshed, because the instruction set and the peripherals stay familiar.
Those refreshes run into availability rather than performance. The MCU cross reference page covers how we compare a replacement processor on the peripheral set and the boot path, which is where a swap usually breaks.
The sourcing side of this part is covered on the date code management. For a processor that is often bought from stock rather than from the factory, that page covers how age and packaging are tracked.
Questions we get on this code
Can it run from a single 3.3 V rail? The core needs 1.3 V and the internal regulator can supply it at 120 MHz, so the board needs the 1.3 V rail only if the PLL is pushed higher. The I/O and the analog blocks still need their own rails as listed in the data sheet.
How much audio processing fits in 256 kilobytes? Enough for a stereo filter chain and a codec at 48 kHz, not enough for a large reverb or a room correction engine with long delays. Those need external memory, and the external memory interface is there for it.
Is the ROM boot loader useful in production? Yes, it can load from SPI EEPROM, NAND or UART, which removes a programming step from the line. The boot source is selected by pins, so the choice is fixed by the board rather than by software.
What about the higher speed grades? They need an external 1.4 V core supply and a different board, so a product that may later need 150 MHz should bring that rail out now rather than respin later.