Contact Us

TMP75CIDR

Brand: Texas Instruments
Texas Instruments TMP75CIDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP75CIDR — Power Management & Signal Chain | Superb Automation

TMP75CIDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP75CIDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP75CIDR: the 1.8 V branch of the LM75 format sensor

TMP75CIDR is not a grade of the TMP75. It is a separate device with its own document, SBOS707B, and the differences are the ones that decide whether it fits a board: a supply range of 1.4 V to 3.6 V, an operating window of minus 55 to plus 125, a fixed 12 bit resolution, and an accuracy of 0.25 degrees typical between 0 and 70. It is pin and register compatible with the NCT75 and the ADT75, which is the sentence most buyers are actually looking for.

The part draws 15 microamps active and 0.3 microamps in shutdown, both typical. On a 1.8 V rail that is a rounding error next to the processor it is watching, and it means the sensor can stay powered from the always on domain instead of being switched by a load switch. That single property removes a component and a failure mode from the board.

The document is short and the specification table is tighter than the industrial TMP75 one, so the numbers below are read straight from SBOS707B and from the orderable addendum at the back. Where the two documents disagree, the disagreement is stated rather than smoothed over, because a customer comparing a quotation against a datasheet will find it anyway.

What changes when the rail drops to 1.8 V

The TMP75 parent runs from 2.7 V to 5.5 V. The C branch runs from 1.4 V to 3.6 V. Those windows overlap between 2.7 and 3.6, which is where most of the confusion starts: a board at 3.3 V can take either part, and the choice then comes down to accuracy and resolution rather than supply.

The C part wins on accuracy at room temperature: 0.25 degrees typical from 0 to 70, against 1 degree typical for the parent. It loses the resolution ladder, because it is fixed at 12 bits with a 0.0625 degree step and no way to trade resolution for conversion time. On a board that wants a fast 9 bit reading, the parent is the better part. On a board that wants the best room temperature number for the least current, the C part wins.

The operating window is the third difference and the one that catches people. The C part starts at minus 55, which is ten degrees below the parent, and stops at plus 125 like the parent. For a cold chain logger or an outdoor enclosure that is a real advantage. For a board that only ever sees 0 to 70, it is a number nobody uses.

Functiondigital temperature sensor, two wire interface
Supply range1.4 V to 3.6 V
Operating rangeminus 55 to plus 125 degrees Celsius
Accuracy0.25 degrees typical from 0 to 70
Accuracy, wider window0.5 degrees typical from minus 20 to plus 85
Accuracy, full window1 degree typical from minus 55 to plus 125
Resolution12 bits fixed, 0.0625 degree step
Active current15 microamps typical
Shutdown current0.3 microamps typical
Addresses8 pin programmable addresses
Alert outputopen drain with programmable trip values
One shot modesingle conversion on command
Compatibilitypin and register compatible with NCT75 and ADT75
PackageSOIC, D body, 8 pins, 4.90 mm by 3.91 mm
Carrier2500 pieces on a large reel
Moisture levellevel 2 at 260 degrees, one year floor life

The NCT75 and ADT75 compatibility is the real feature

Two competitors named in the first line of the document is unusual, and it tells you what the part is for. Boards that were specified around an NCT75 or an ADT75 can take the TMP75C without a change to the register map, the address strapping or the footprint. The trip register, the configuration register and the temperature register all answer at the same addresses.

That makes this string a natural second source rather than a new part. When a customer tells us the NCT75 is on allocation, the question is not whether the TMP75C works, it is whether the firmware writes anything to a register the TMP75C does not implement. In our experience the answer is usually no, and the check takes an afternoon rather than a week. The pin to pin cross reference page describes how we run that check, and the obsolete part cross reference hub page covers the case where the original part has already gone end of life.

The one caveat is the supply range. An NCT75 board at 3.3 V is inside both windows. A board at 5 V is not inside the TMP75C window at all, and that is where the substitution stops, no matter what the register map says.

Reading the accuracy curve instead of the headline number

0.25 degrees typical sounds like a precision part until the word typical is weighed. The document prints typical values across three windows and leaves the maximum limits to the electrical table. On a production line the maximum is what matters, and the maximum is not 0.25 degrees.

The practical consequence is that this part is a monitor, not a reference. It is excellent for thermal compensation of another sensor, for fan curves, for throttling a processor and for logging. It is not the part to use when the temperature reading is the measurement the instrument sells. For that job the answer is a calibrated probe or a remote diode part with a specified maximum over the window that matters.

The 0.0625 degree step is finer than the accuracy, which is normal and not a fault. It means a trend line drawn from successive readings has resolution below the error, so averaging helps, and a moving average over ten readings is a legitimate way to get a number that behaves better than a single conversion.

Board notes and address handling for the whole family

The two wire bus is the only high impedance node on the part, and it is the only place where the board can hurt the reading. Long stubs, missing pull ups and a shared bus with a slow device all show up as intermittent acknowledge failures rather than as temperature errors. Keep the bus pull ups at the master end of the segment and keep the sensor within a few centimetres of the connector.

The address pins are read at power up. A pin left floating is not a defined address, and a board that relies on an internal pull down to set the code is relying on a specification the document does not promise. Strap the three pins high or low with resistors, and record the strap pattern on the assembly drawing so the next build does not guess.

The thermal path is the second half of the measurement. The part measures its own die, and the die is connected to the package lead frame, which is connected to the copper under the body. A sensor placed on a thick ground plane reads the plane, not the air. That is fine when the plane is the thing being monitored and misleading when the air is.

Where this part is the right answer

The document lists server and computer thermal management, telecommunication equipment, office machines, video game consoles and set top boxes. The pattern is a 1.8 V or 3.3 V rail, a bus that already exists, and a need for a number that is good enough to drive a fan or a throttle.

Telecom line cards are the strongest fit in our order book. The rail is 1.8 V or 3.3 V, the bus is I2C and already goes to the shelf controller, and the sensor sits next to an optical module that runs hot. The 0.25 degree typical accuracy at room temperature is more than the fan curve needs, and the 15 microamp draw means the sensor never appears in the power budget.

Three questions buyers ask about this string

Will it work at 5 V? No. 3.6 V is the maximum. Use the TMP75 parent for a 5 V rail.

Is the C suffix a cost reduced part? It is a different device with a lower supply floor and a tighter room temperature accuracy. It is cheaper in volume because it is built on a smaller geometry, not because it is a degraded version of the parent.

Does it need a pull up on the ALERT pin? Yes, it is open drain. The ALERT pin can be left unconnected if the alarm function is not used, but the trip registers then have no effect and the firmware should not wait on them.