TMP75AQDRQ1
Product Specifications
TMP75AQDRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMP75AQDRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMP75AQDRQ1: the automotive grade of the eight address LM75 format sensor
TMP75AQDRQ1 is the AEC-Q100 grade 1 member of the TMP75 family, in the 8 pin SOIC body, on a 2500 piece reel. It reads temperature with a 12 bit converter and reports it over the same two wire interface and the same register map that the LM75 established, so a pack that was specified around an LM75 footprint takes this part without changing the address decoding in the firmware.
The reason this string exists in our catalogue at all is that the industrial and automotive versions are not the same part, and the difference is not cosmetic. The industrial TMP75 prints 2 degrees maximum over minus 40 to plus 125. The automotive TMP75-Q1 prints 3 degrees maximum over the same window, with grade 1 qualification and the HBM and CDM classification that go with it. A buyer who quotes the industrial figure against an automotive order is quoting a promise the silicon does not make, and that is the first thing we check when a BOM crosses from a commercial build into a vehicle build.
Every figure below is from SBOS759 for the automotive device and SBOS288M for the industrial parent, both read against the orderable addendum at the back of each document. The two documents agree on the interface, the resolution ladder, the supply range and the package, and disagree on the accuracy limit, which is exactly the sort of split that a sourcing plan has to carry.
What the QDR suffix tells you
The order code breaks into four pieces. TMP75 is the device family. A is the accuracy grade. QDR is the SOIC body in tape and reel with the automotive qualifier, and Q1 is the qualification level. The addendum prints TMP75AQDRQ1 as active, production, SOIC with 8 pins, 2500 pieces on a large reel, NIPDAU lead finish, moisture level 2 at 260 degrees for one year, and a marking of 75Q1.
That marking matters during goods inward. A reel of TMP75AQDRQ1 carries 75Q1 on the body, while the industrial TMP75AIDR carries a different mark and the VSSOP version carries 175Q for the twenty seven address part. A reel whose marking does not match the order code is the cheapest counterfeit signal available, and it costs nothing to check at the door.
| Function | digital temperature sensor, two wire interface |
| Interface | SMBus, two wire and I2C compatible |
| Addresses | 8 pin programmable addresses through A0 to A2 |
| Resolution | 9 to 12 bits, user selectable |
| Resolution step | 0.5 degrees at 9 bits down to 0.0625 degrees at 12 bits |
| Conversion time | 27.5 ms at 9 bits, 55 ms at 10, 110 ms at 11, 220 ms at 12 |
| Accuracy, automotive | 1 degree typical, 3 degrees maximum from minus 40 to plus 125 |
| Accuracy, industrial parent | 1 degree typical, 2 degrees maximum over the same window |
| Supply range | 2.7 V to 5.5 V |
| Quiescent current | 50 microamps typical, 0.1 microamp in standby |
| Alert output | open drain, programmable trip and hysteresis |
| Package | SOIC, D body, 8 pins, 4.90 mm by 3.91 mm |
| Thermal resistance | printed in the thermal table for the D body |
| Carrier | 2500 pieces on a large reel |
| Marking | 75Q1 |
| Moisture level | level 2 at 260 degrees, one year floor life |
| Qualification | AEC-Q100 grade 1, HBM level 2, CDM level C6 |
The resolution ladder is a schedule decision, not a precision decision
Four settings, four conversion times, and the trade is linear: halving the resolution halves the conversion time. At 12 bits the part needs 220 ms per conversion, which is 4.5 readings per second. At 9 bits it needs 27.5 ms, which is 36 readings per second. On a thermal model of a power stage that is the difference between catching a fast transient and missing it, and on a battery powered node it is the difference between a duty cycle that fits the energy budget and one that does not.
The tempting mistake is to set 12 bits everywhere because the number looks better. The accuracy of the part is 3 degrees maximum in the automotive grade, which is 48 counts at 0.0625 degrees. Spending 220 ms to resolve 0.0625 degrees when the part is only good to 3 degrees is buying resolution that the accuracy does not support. Our rule of thumb on a control loop is 10 or 11 bits, and 12 bits only where the reading is logged for a trend rather than used for a decision.
The one shot mode is the other half of that arithmetic. A node that wakes on a timer, starts a conversion, reads the result and goes back to standby never pays the quiescent current between readings. At 0.1 microamps in standby, the energy budget is decided by the conversion time and the wake overhead, not by the sensor.
Where the eight address limit bites
Three address pins give eight combinations on one bus segment, and the ALERT line is shared. That is enough for a rack of eight line cards, an eight cell battery stack, or eight hot spots on one chassis. Past eight, the answer is a second segment or an I2C multiplexer, and both cost more than the sensor.
The TMP175 member of the family raises the count to twenty seven by using the same three pins as a wider code, at the cost of a different register map and a different accuracy grade. Boards that were laid out for the eight address part cannot simply take the twenty seven address part, because the pin strapping means something else. The two are not interchangeable, and that is worth saying out loud before somebody orders the cheaper of the two against the wrong BOM line.
Address conflicts on a shared bus are the most common integration fault we see on this family. Two sensors strapped to the same code produce a bus that answers with the wired AND of both devices, and the reading looks plausible for a while, which is worse than looking broken. Our incoming inspection plan page describes the address strap check we run on a sample from each reel, and the component traceability report page covers how the lot is recorded when a customer needs the trail.
What an automotive order needs beyond the part number
Grade 1 covers minus 40 to plus 125 ambient, which is the widest of the four automotive grades. It does not by itself cover the documentation a tier one supplier will ask for. Production part approval, a control plan, the material declaration and the change notification agreement are separate deliverables, and on a first order they take longer than the parts.
The moisture level is the second item. Level 2 at 260 degrees gives one year of floor life out of the bag. A line that keeps a partial reel on the feeder over a weekend is inside that window, but a reel opened last quarter is not, and the bake step adds a day. On an automotive schedule, that day is planned, not discovered.
The last item is the change history. The industrial document moved the absolute maximum supply from 7 V to 6.5 V between revisions and added pin qualifiers to the input voltage row. A customer who qualified against an older revision and reads a newer one will ask whether the part changed. It did not; the document did, and the answer is to point at the revision history rather than to re-qualify.
Applications where this string earns its place
The automotive document lists climate control, infotainment processor management, airflow sensors, battery control units, engine control units, urea sensors and water pumps. The common thread is a module that has to report its own temperature over a bus that already exists, with no calibration step at the end of the line.
In a battery control unit the sensor is usually not measuring the cell, it is measuring the board next to the cell. The 3 degree limit is fine for that job because the gradient between the board and the cell is larger than the error. In an infotainment head unit the sensor watches the processor package edge, and the same reasoning applies. Where the number has to be better than 3 degrees, the job belongs to a remote diode part, not to this family.
Three questions buyers ask about this string
Is the automotive part a drop in replacement for the industrial part? Same body, same pinout, same register map, same supply range, wider qualification and a looser accuracy limit. Electrically it works; on paper the accuracy grade changes, so the qualification record has to change too.
Can the 12 bit setting be used with a 1.8 V rail? No. This family runs from 2.7 V. The 1.8 V job belongs to the TMP75C branch, which is a different silicon with a different supply range and a different accuracy ladder.
Does the ALERT pin need a pull up? Yes, it is open drain, and the pull up belongs on the bus side with the rest of the SMBus pull ups. A missing pull up produces a sensor that reads correctly and never alarms.