Contact Us

TMP6131DECR

Brand: Texas Instruments
Texas Instruments TMP6131DECR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP6131DECR — Power Management & Signal Chain | Superb Automation

TMP6131DECR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP6131DECR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP6131DECR silicon linear thermistor with a positive coefficient in the 0402 X1SON body

The TMP6131DECR is the 0402 X1SON member of the TMP6 line, a silicon thermistor with a positive temperature coefficient and a nominal resistance of 10 kilohm at 25 degrees. It is not a digital sensor and it is not an NTC bead: the part is a resistor whose value rises with temperature along a curve the vendor publishes as a resistance to temperature table, so the reading path is a bias resistor and an analogue to digital converter the board already has, not a new bus and not a driver.

The reason a board moves from an NTC to this part is almost always linearity and tolerance at the hot end. A 10 kilohm NTC loses sensitivity as it heats, so the resolution at 100 degrees is a fraction of what it is at 25, and the tolerance stack of a cheap bead forces a calibration step at end of line. This part holds its coefficient across the range, which the vendor prints as 6400 ppm per degree at 25 degrees with a 0.2 percent typical coefficient tolerance, and holds the nominal to plus or minus 1 percent from 0 to 70 degrees.

Key parameters taken from the TMP6131DECR document

ElementSilicon thermistor, positive temperature coefficient, 10 kilohm nominal at 25 C
TolerancePlus or minus 1 percent maximum from 0 to 70 C, plus or minus 1.5 percent over minus 40 to 150 C
Coefficient6400 ppm per C at 25 C, typically 5910 at 85 C and 6220 at minus 35 C
Coefficient tolerance0.2 percent typical at 25 C, 0.4 percent typical at minus 35 C
RangeMinus 40 to plus 150 C continuous, with fail-safe behaviour at the top of the range
Response0.6 s thermal response, the figure the document quotes for the 0402 DEC body
Drift0.5 percent typical long term drift after 1000 hours at 150 C, 1.2 percent maximum in the 0603 body
Fail behaviourShort to the supply raises the resistance, so the reading fails high and a supervisor trips rather than reading a false cool
Body0402 X1SON, DEC suffix, two terminals, no external components
BiasExcited by a divider, a current source or a bridge, the same front end used for any resistive sensor
ConversionResistance to temperature table supplied by the vendor, plus the board tool that generates the table
Self heatingSmall thermal mass and low excitation power keep the element close to the temperature being measured
Order code factsTMP6131DECR, 0402 X1SON body, tape and reel, catalog grade
Second source noteThe same die appears as TMP61 in the 0603 SOT-5X3 body and in a two pin TO-92S body, so the curve does not change when the body changes

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The bias resistor sets the resolution of the whole measurement, not the sensor. With a 10 kilohm element and a 10 kilohm pull up, the divider gives the largest change per degree around the middle of the range and the smallest at both ends, and the analogue to digital converter has to resolve that smallest step. Before the board is frozen, plot the divider output over the full temperature range at the actual excitation voltage and check the converter step against the accuracy the product needs, because the sensor accuracy of one percent is wasted if the front end only delivers three degrees of resolution near the trip point.

Self heating is the quiet error on a part this small. The 0402 body has very little thermal mass, which is why it responds in 0.6 s, and the same property means a milliwatt of excitation warms the element above the thing it is measuring. The document tells the reader to keep excitation low for exactly this reason. On a 3.3 V rail a 10 kilohm divider dissipates about a quarter of a milliwatt at 25 degrees and more as the resistance falls at cold, so the practical rule is to power the divider from a switched rail and read it in a short burst rather than leave it energised all the time.

The fail-safe direction of a positive coefficient part is worth stating to the safety reviewer in plain words. If the element is shorted to the supply, the measured temperature reads hot and the system shuts down; if it opens, the divider reads the cold extreme and the firmware sees an implausible value rather than a plausible one. That is the opposite of an NTC, where a short reads hot and an open reads cold on some dividers and the other way round on others depending on the topology. A product that was qualified with an NTC keeps its behaviour only if the divider and the plausibility window are reworked, not just the part number.

The 0402 body is also the reason this part shows up in power stage work. It can be placed inside the switching cell, close to a MOSFET tab or a shunt, and report the local temperature rather than the temperature at the end of a copper trace. The board rules is to keep the two traces to the element short and equal and to keep them away from the gate drive loop, because a few millivolts of coupling into a divider that changes by tens of millivolts per degree turns into a temperature error the calibration cannot remove.

  • Divider output over the full range, measured at the actual excitation voltage and compared against the converter step.
  • Self heating with the divider energised continuously, then again with the burst read the production firmware will use.
  • Resistance at 25 degrees on the first article, against the 9.9 to 10.1 kilohm window.
  • Response time in the real assembly, with the part bonded or glued to the surface it is meant to watch.
  • Behaviour with the element shorted and with it open, recorded for the safety file.
  • Placement review against the gate drive loop and the shunt, on the actual copper.

Which projects this part fits

This part fits battery pack temperature sensing, motor and inverter hot spot monitoring, power supply thermal protection, HVAC and thermostat probes, display backlight compensation and appliance control boards. It is the natural choice where the product already has an analogue front end, where an NTC calibration step at end of line is expensive, or where the measurement has to stay usable at 125 to 150 degrees. For SUPERB customers in power electronics and industrial control it is also a practical answer to an NTC shortage, because the reading path changes but the board does not need a new bus or a new processor pin.

Questions that come up before a purchase order is released

Is this a drop in replacement for a 10 kilohm NTC?

Electrically it is the same two terminal resistor, so the footprint and the divider stay. What changes is the curve: the resistance rises with temperature instead of falling. Any firmware that converts an NTC reading has to be replaced by the table for this part, and any plausibility window or fail direction has to be rechecked, because a short now reads hot where an NTC short read hot only on some dividers and cold on others.

What does the DEC suffix mean?

It is the 0402 X1SON body. The same die ships in a 0603 SOT-5X3 body and in a two pin TO-92S body, and the document prints one curve for the family. A change of body changes the thermal response and the placement options, not the resistance to temperature relationship, so a board that moves between bodies keeps one table.

How accurate is the part at the top of the range?

The plus or minus 1 percent figure belongs to 0 to 70 degrees. Over the full minus 40 to plus 150 degrees the document prints plus or minus 1.5 percent, and the coefficient itself carries 0.2 percent typical tolerance at 25 degrees. A product that needs one degree at 140 degrees should read the resistance at that point from the table rather than scaling from the 25 degree value.

Can it be read by a comparator instead of a converter?

Yes, and that is common in protection circuits. The coefficient is large enough that a fixed threshold on the divider gives a trip point with a few degrees of spread, and the fail-safe direction means a broken sensor drives the node to one rail rather than floating. A comparator board does need the divider tolerances checked, because the trip point moves with both resistors.

What documentation comes with the shipment?

The reels carry the vendor marking and a date code, and the resistance to temperature table is a document the engineering team keeps rather than something in the box. We supply the parts with lot traceability and can provide the vendor document number on request, which is what an audit usually asks for.

How SUPERB handles this line

We supply the TMP6131DECR from original reels with lot traceability, and we check the body and the marking against the code before the parts reach a line. If the board is moving from an NTC, the useful starting point is the power management cross reference page, where the reading path and the part families are listed together. For programs that need a second body or a second source, the component obsolescence management page covers how a family stays available when one package is discontinued, and incoming inspection plan covers what to measure when the parts arrive.