Contact Us

TMP431DDGKR

Brand: Texas Instruments
Texas Instruments TMP431DDGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP431DDGKR — Power Management & Signal Chain | Superb Automation

TMP431DDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP431DDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP431DDGKR: a remote diode sensor that compensates for low beta

TMP431DDGKR is a remote temperature sensor with one diode channel and one local channel, in the 8-pin VSSOP body, on a 2500 piece reel. Its distinguishing feature is automatic beta compensation: it measures a transistor with a current gain as low as 0.1 without the reading collapsing, which is what a substrate PNP on a modern processor looks like to a sensor that only corrects for ideality.

The part matters because the diodes available on silicon have changed. A discrete 2N3906 has a beta in the hundreds and any remote sensor reads it correctly. A substrate PNP inside a 28 nm or 16 nm processor can have a beta near 3, and a sensor without beta compensation reports a temperature that is wrong by tens of degrees at the top of the range while looking plausible at room temperature. That failure mode is why this family exists and why the older two channel part is not a substitute.

The values below come from SBOS441I, revised October 2019, and from the package option addendum. They cover the accuracy split between the remote and local channels, the conversion time with beta correction enabled and disabled, the 12-bit resolution, the programmable limits, and the series resistance the part can cancel in each mode.

What beta compensation actually does

A diode connected transistor is measured by forcing two or three different currents through it and reading the resulting base emitter voltages. The difference between those voltages is proportional to absolute temperature, but it also depends on the ideality factor and on how much of the forced current reaches the collector rather than the base. When beta is high, almost all of it reaches the collector and the arithmetic is clean. When beta is 3, a third of the current goes into the base, the current density ratio is not the one the sensor assumes, and the computed temperature is too high.

The TMP431 measures the base current as well as the collector current, works out beta, and corrects the result. The compensation range printed in the electrical table is 0.1 to 27, which covers everything from a fine geometry substrate PNP up to a discrete small signal transistor. Above a beta of 27 the correction is not needed and the part is configured for a plain diode; the setting is a register field, not a strap, so a single board can serve two different processor families with a firmware change.

The cost of the correction is time. With beta correction enabled and the recommended configuration, a remote conversion takes 126 milliseconds typical; with correction disabled it takes 47 milliseconds. The local channel takes 15 milliseconds either way. A host that samples once a second does not care about the difference; a host that runs a fast throttle loop should know that the fast mode is only available with correction off.

Channelsone local, one remote diode
Remote accuracy0.25 degrees typical, 1 degree maximum from 0 to 100 degrees at the diode
Local accuracy1.25 degrees typical, 2.5 degrees maximum over minus 40 to 125
Resolution12 bits, 0.0625 degrees per count
Conversion, local15 milliseconds typical, 17 maximum
Conversion, remote with beta126 milliseconds typical with the recommended filter, 47 without
Conversion, remote without beta93 milliseconds typical with the filter, 44 without
Beta compensation range0.1 to 27
Series resistance cancelled300 ohms with beta on, 1 k with beta off
Ideality factor1.000 or 1.008, selected by register
Supply range2.7 V to 5.5 V
Quiescent current35 microamps typical at the slowest rate, 0.7 mA at eight conversions per second
Shutdown current3 microamps typical, 10 maximum
InterfaceSMBus two wire, 400 kHz fast mode, 2.5 MHz high speed mode
PackageVSSOP-8, DGK, 3.00 mm by 3.00 mm
Thermal resistance168.2 degrees per watt junction to ambient
Carrier2500 pieces on a large reel, marking DSCI
Moisture levellevel 2 at 260 degrees, one year floor life

The two output pins and what they can drive

Pin 6 is ALERT and pin 7 is THERM2 on this body, and the two pins are configured independently. ALERT is the SMBus alert: it asserts when a measured temperature crosses a programmable limit, and it can be masked per channel so that a small excursion on the local channel does not wake the host. THERM2 is a second threshold that can be set higher and used as a hardware throttle line, which is the pin a power management controller watches when firmware has stopped responding.

The outputs are open drain and sink 6 milliamps at 0.4 V, so they drive an LED, a fan controller input or a supervisor reset line directly. The default state after reset is a defined one, which matters on a board where the sensor is powered before the processor: the alert line is released and the host sees a clean start rather than a spurious thermal event.

Both limits are 8-bit registers with a sign bit, so a threshold can be set below zero. The part also keeps minimum and maximum registers for each channel, which is the cheapest way to answer the question a field return always asks: what was the hottest temperature this board ever saw. The registers survive as long as the part is powered and can be cleared by the host after a read.

The filter in front of the diode pair

The document's recommended circuit puts a resistor and a capacitor across the diode pair, and the conversion time table refers to that arrangement as RC equals one. The filter serves two purposes: it removes noise picked up by the trace, and it makes the part tolerant of the capacitance a long cable presents. Without the filter the conversion is faster, 47 milliseconds instead of 126 with beta correction on, but the reading is more exposed to noise.

Series resistance cancellation has a limit that the filter consumes. With beta correction enabled the part cancels up to 300 ohms; a filter built from two 100 ohm resistors uses two thirds of that budget before the trace resistance is counted. With beta correction disabled the budget is 1 k, which is why some boards run without correction on a discrete transistor and a heavier filter.

For a remote diode inside a processor package, the trace is short and the filter is small. For a discrete transistor on a heatsink, the cable can be 300 mm and the filter has to be sized against the cancellation budget. We check that arithmetic on any board where the sensor and the transistor are on different assemblies, and the incoming inspection plan page describes how we verify the parts that go into that chain.

Reading a 12-bit remote channel over SMBus

Each channel has a high byte and a low byte. The high byte holds the integer part in degrees and the low byte holds the fraction in sixteenths of a degree above the 4-bit field, so a 12-bit read is two bytes and the fraction resolution is 0.0625 degrees. The document also prints a 13-bit extended format for the remote channel on some members, and the extra bit extends the range rather than the resolution.

The bus is a standard SMBus two wire interface with a 30 millisecond timeout, which means a host that stops clocking in the middle of a transfer does not lock the part up: the interface resets itself and the next transaction starts cleanly. That behaviour is worth knowing on a board where the processor can be reset in the middle of a poll, which is common in telecom line cards.

The address is set by the A0 pin on this body, giving two addresses on one segment. A board with two processors needs two parts or a second segment, and a board with more than two needs a multiplexer. The three channel member of the family and the TMP422 cover the other cases.

Where the part is used

The document lists LCD, DLP and LCOS projectors, servers, industrial controllers, central office telecom equipment, desktop and notebook computers, storage area networks, industrial and medical equipment, and processor and FPGA monitoring. The beta compensation feature is what makes the server and telecom entries credible: those boards carry processors whose diodes a plain sensor cannot read.

On our side the string appears in telecom line cards, in instrument front ends and in RF power amplifiers where a diode is brought out of the transistor die. In the RF case the remote channel measures the junction rather than the case, which is the difference between a protection loop that works and one that trips late. Our RF component sourcing page lists the parts we hold for those builds.

For a customer moving from an older sensor, the check is not the pin count. The older parts assume a beta above 10 and an ideality near 1.008; this part can be configured for either, and the register that does it is the one to document in the build file. The pin to pin cross reference page describes how we compare the electrical behaviour before a substitution is signed off.

Three questions buyers ask about this string

Is the local channel accurate enough to protect the board on its own? It is specified to 2.5 degrees maximum over the full window, which is fine for ambient and fan failure detection and not fine for protecting a die. Use the remote channel for silicon.

Does the part need a calibration on the production line? No. The remote accuracy is specified without calibration and the beta compensation is automatic once the register is set. A one point check at room temperature is enough to confirm the assembly.

Can the THERM2 pin drive a fan directly? It can sink 6 milliamps, which is enough for a controller input and not enough for a fan. Use it into a fan controller or a transistor, and keep the pull-up above 10 k to limit the current when the output is low.