Contact Us

TMP110D0IDPWR

Brand: Texas Instruments
Texas Instruments TMP110D0IDPWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP110D0IDPWR — Power Management & Signal Chain | Superb Automation

TMP110D0IDPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP110D0IDPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP110D0IDPWR: a temperature sensor for a cost sensitive board

The TMP110D0IDPWR is an I2C digital temperature sensor in a five pin X2SON package measuring 0.8 mm by 0.8 mm by 0.4 mm. It is specified at plus or minus 1.0 C maximum from minus 40 to 125 C, runs from 1.14 V to 5.5 V, and resolves to 0.0625 C.

The fifth pin is the interesting one. On the D0 version it is used as an address pin, which allows two devices on one bus without a multiplexer. On other versions in the same family the pin becomes an alert output. One package, two behaviours, decided by the order code.

Average current is 55 microamps at an active conversion rate, with 0.15 microamps in shutdown. That is not the lowest in the catalogue, but it is low enough for a battery powered product that measures occasionally, and the supply range down to 1.14 V means it can run from a single cell without a boost stage.

Key data for the TMP110D0IDPWR

FunctionDigital temperature sensor with an I2C interface
AccuracyPlus or minus 1.0 C maximum from minus 40 to 125 C
Resolution0.0625 C per step
Supply1.14 V to 5.5 V
Current55 microamps active, 0.15 microamps shutdown
PackageX2SON, 5 pins, 0.8 mm by 0.8 mm by 0.4 mm
Pin fiveAddress select on the D0 version, alert output on other versions
InterfaceI2C and SMBus compatible
Temperature rangeMinus 40 to 125 C operation
OrderingTMP110D0IDPWR, large tape and reel

One point one four volts, and what it allows

A sensor that runs from 1.14 V can sit directly on a single lithium cell, on a 1.2 V rail, or on a coin cell that has sagged. That removes a regulator from the board and removes the quiescent current that the regulator would have drawn, which on a product that sleeps for a year is the whole budget.

The bus has to match. An I2C bus on a 1.2 V rail needs a host that runs at the same level, or a level shifter that costs more than the sensor. In practice the low supply range is used with a host that is also on a low rail, which is the case in wearables and small battery products.

The upper end at 5.5 V covers a 5 V board as well, so the same part number works on both, and a product family can standardise on it.

The pin that is either an address or an alert

Choosing between two addresses and an alert is a real constraint, and it is decided by the order code before the board exists. A product that wants two sensors and an alert needs two buses or a multiplexer, because the pin cannot do both.

Where the alert is fitted, it is an open drain output with a programmable limit. That is enough to wake a host or to drive a fan controller, and it does not need the host to poll the bus. Where the address pin is fitted, the host has to poll, and the polling rate sets the current.

Boards that are built with the wrong version pass a temperature test and fail a system test, because the pin behaves as an address and the host is waiting for an interrupt that never comes.

Where it fits in a build

Wearables, small battery products, consumer appliances and any board where the sensor is one line item among many. At this price point the part is chosen on the supply range and the package, not on the last tenth of a degree.

Because the cost matters, the sourcing route matters too. The how to reduce component cost page covers how we compare a part against alternates on the total cost of the build rather than the unit price, and the one stop BOM sourcing page covers how the small parts are consolidated into one release.

The sourcing side of this part is covered on the vendor consolidation. For a product whose bill of material carries several small sensors, that page covers how the supply is consolidated without losing control of the part numbers.

Questions we get on this code

Does it need a decoupling capacitor? Yes, a small one close to the supply pin. At 0.8 mm the package has no room for a capacitor inside, and a conversion draws a short current pulse.

Can it be used at 5 V? Yes, up to 5.5 V, and the accuracy is specified across the whole range.

What is the conversion time? A single conversion completes in a few milliseconds and the part returns to its idle current. The average current depends on how often the host asks for a reading.

Is the D0 version the same die as the alert versions? Yes, the pin function is selected by the order code. Two different part numbers are needed for two different behaviours.